Department Of Fertilizers - Haryana

39615350 bids are invited for forged cs gate valve size half inch rating 1500 with specification as per gem technical sheet , forged cs gate valve size three by four inch rating 1500 ibr with specification as per gem technical sheet , cs gate valve api 602 size one and half inch rating 150 with specification as per gem technical sheet , cs gate valve api 600 size one and half inch rating 150 with specification as per gem technical sheet , forged alloy steel gate valve size half inch rating 1500 ibr with specification as per gem technical sheet , forged alloy steel gate valve size 1 inch rating 1500 ibr with specification as per gem technical sheet , forged alloy steel globe valve size one and half inch rating 2500 ibr with specification as per gem technical sheet , ball valve size 1 inch with specification as per gem technical sheet , ball valve size three fourth inch with specification as per gem technical sheet total quantity : 208...

Haryana Power Generation Corporation Limited - Haryana

39553867 tender for supply of pneumatic & manual isolation valves 1. zero passing integrated metal seated ball valve. remote operated with 5 7 kg air pressure air to close (no air to open) pneumatic steam drain isolation ball valve with pneumatic actuator, forged alloy steel (f22), press (bar) & temp (°c): 180 & 540, pipe dimension & connection: ø48x10sw, 4500 1.5” 06 xen/stores, dcrtpp, yamuna nagar 2. zero passing integrated metal seated manual ball valve. forged alloy steel (f22), press (bar) & temp (°c): 180 & 540, pipe dimension & connection: ø48x10sw, 4500 1.5” 04 3. zero passing integrated metal seated manual ball valve. forged alloy steel (f22) lever operated, press (bar) & temp (°c) : 180 & 540, pipe dimension & connection: ø60x11sw, 4500 2” 02 4. zero passing integrated metal seated ball valve. forged carbon steel, socket weld. remote operated with 5 7kg air pressure air to close (no air to open), pneumatic steam drain isolation ball valve with pneumatic actuator, press (bar) & temp (°c) : 45 & 540, pipe dimension & connection: ø48x10sw, 2500 1.5” 05 note i shut off shall be absolute zero leakage. valve seat, gland, body seals and studs shall be tested to zero bubbles and zero drops of leakage test certificate provided. all valves and attached fittings shall be ibr certified. note ii guarantee class 04 years zero leakage (zero bubbles). in case of any failure/defect/passing/internal leakage observed in any installed valves, the supplier has to replace the valve at the earliest possible time (within maximum period of 30 days) after intimation given to supplier. note iii commissioning support shall be provided free of cost for installation of the valves (maximum 10 days). operation & maintenance manuals and drawing shall be provided by firm....

Urban Local Bodies - Haryana

39530478 providing and supply of tools equipments for ward 2, 4 and 35 to 40, division iv, horticulture wing, mcf. 1 kassi 2 panji 3 hedge shear 10” blades with plastic handle 4 grass sword 5 khurpa size : 1` x 5` 6 shrub masterworking width– 52” – 55” no. of blades– 2 3 pcs pto shaft–with safety lockchain attachment – available with chainpreferred brand – shaktiman / unison / lawn king / garden king / sharpexcomplete in all respect to full satisfaction of engineering – incharge 7 diesel engine walk behind lawn mowerscutting width – 20” 24”forward speed – adjustable with clutch platebottom blade – made up of specially bent alloy steel for longer and durable performance preferred brand – unison / lawn king / garden king / sharpex / primco powercomplete in all respect to full satisfaction of engineering – incharge 8 petrol operated brush cutterlength – 179 cm minimumweight – 8 8.5 kg.engine type – petrol operatedpreferred brand – stihl / unison / lawn king / garden king / sharpex / primco powercomplete in all respect to full satisfaction of engineering – incharge 9 petrol operated hedge trimmer – preferred brand – stihl / honda / unison / lawn king / garden king / sharpex / primco powerpower: 0.75 kw / 1.14 hpengine type – petrol operatedblade type – high actionblade length –60 cm minimumcomplete in all respect to full satisfaction of engineering – incharge 10 chain sawpreferred brand – stihl / honda / unison / lawn king / garden king / sharpex / primco powerbar length – 25”power source – petrol operatedengine type – 2 strokefuel tank capacity – 0.68 ltr. chain oil capacity 0.38 ltrpower output – 3.9 / 5.3 kw / bhpweight – 7kg approx. 11 earth augarpower:6.5 hpengine type:single cylinder, 4 strokecooling type:air cooledfuel type: petrol onlyengine oil:4 stroke engine oildisplacement: 196ccstarting system:recoil startmax. troque ( n. m / r / min ) :10.5bit / driller length:80cm / 2.6 footdriller:16 inch / 400mmdimension:75x50x110 cmweight: 32 kg approx.. 12 daav 13 rose cutter...

Haryana Power Generation Corporation Limited - Haryana

39529016 tender for supply of emergency drain control valve of hph 7&8 1 high pressure heater (hph 7) emergency drain control valveapplication: high pressure heater (hph 7) emergency drain control valve, size:4 body style globe, mass flow rate liquid (wi) 171540 kg/h, temperatureratings for standard class astm a217 grade wc9 valves (in accordance with asme b16.34) rating cl900, body wc9 alloy steel, end connection butt welded sch 80, cage: sst, seat ring: sst valve plug: sst, equal percentage flow characteristic, equal percentage cage, hydrodynamic trim valve lpa (lpae1m) <85db(a), push down to close, cl5 leakage, shutoff class ansi cl v, pneumatic actuator push down to close & 75 psi maximum casing press, smart positioner, air fail to open, handwheel handwheel for manual operation.working parameters: valve inlet pressure & temp:4.81mpa & 265 deg c, valve outlet pressure: under vacuum 0.92bar 2 high pressure heater (hph 8) emergency drain control valveapplication: high pressure heater (hph 8) emergency drain control valve, size:3 body style globe, mass flow rate liquid (wi) 85890 kg/h, temperatureratings for standard classastm a217 grade wc9 valves (in accordance with asme b16.34) rating cl1500, body wc9 alloy steel, end connection butt welded sch 80, cage: sst, seat ring: sst valve plug: sst, equal percentage flow characteristic, equal percentage cage, hydrodynamic trim valve lpa (lpae1m) <85db(a), push down to close, cl5 leakage, shutoff class ansi cl v, pneumatic actuator push down to close & 75 psi maximum casing press, smart positioner, air fail to open, handwheel handwheel for manual operation.working parameters: valve inlet pressure & temp:7.58mpa & 295 deg c, valve outlet pressure: under vacuum 0.92bar ...

Haryana Power Generation Corporation Limited - Haryana

39441168 tender for supply of nut, bolt and washer to rgtpp, khedar, his 1 supply of nut, bolt and washer to rgtpp, khedar, hisar 2 ms hex nut m12 3 ms hex nut m16 4 ms nut m20 5 ms nut m24 6 ht nut m20 7 ht nut m24 8 ht nut m16 9 ht plain washer m24 10 ms washer m12 11 ms washer m16 12 ms washer m20 13 ms washer m7/8” 14 ms nut m7/8” 15 ms hex bolt 7/8”x8” 16 ms hex bolt 7/8”x6” 17 ms hex bolt m20x65 18 ms hex bolt m12x70 19 ms hex bolt m12x100 20 ms hex bolt m20x100 21 ms hex bolt m20x200 22 ms hex bolt m12x65 23 ms hex bolt m16x100 24 ms hex bolt m16x80 25 ms hex bolt m16x60 26 ms hex bolt m12x50 27 ht hex head bolt m20x80mm f/thread 28 ht hex bolt m20x120 29 ht hex bolt m16x120 30 ht stud m 24x220 with 2 nut & washer 31 ht hex bolt m24x130 32 mshex bolt m24x160 33 ht hex bolt m16x90 34 ss stud with 2 nut and 2 washer 5/8 x 100 mm 35 galvanised stud with 2 nut and 2 washer 5/8 x 210 mm 36 ms hex bolt5/8”x100 mm 37 ms bolt m20x80 38 ms hex bolt m12x40 39 ms hex bolt 1/2x4” 40 ms hex bolt 1/2x2” 41 ms hex nut 1/2 42 ms hex bolt m16x50 43 ms washer m16 44 ms hex bolt m 20x50 45 ms washer m20 46 ms hex nut m20 47 ms hex bolt m 8x40 48 ms hex nut m8 49 ht hex bolt m16x80 50 ht hex m10x50 51 ht hex bolt m10x40 (full thread) 52 ht hex nut m10 53 ht hex bolt m24x120 (half thread) 54 ht hex bolt m30 x150 55 ht nut m30 56 ht hex bolt m8x25mm long full thread 57 ht hex bolt m10x40 mm long full thread 58 ht hex bolt m14x50 mm long full thread 59 ht hex bolt m16x40 mm long full thread 60 ht hex bolt m16x50 mm long full thread 61 ht hex bolt m20x40 mm long full thread 62 ht hex bolt m20x90 mm long full thread 63 ht hex bolt m24x80 mm long full thread 64 ht hex bolt m30x80 mm long full thread 65 ht hex nut m12 66 ht allen bolt m20x45 mm long full thread 67 csk bolt with nut m10x35 mm long full thread 68 ms hex nut with bolt m16x250 mm long full thread 69 ht hex bolt with nut m8x25 mm f/t 70 ht hex bolt m12x25 mm f/t 71 ht hex bolt m20x60 mm f/t 72 ht stud m16x70 73 ht nuts m20 74 spring washer m8 75 spring washer m12 76 sprig washer m20 77 ss bolt with nut & washer m16x50, full thread 78 ht machined washer m40 79 spring washer m10 80 ht nut m12 81 ht hex nut m18 82 nylock nut m20 83 ms hex boltm12x200 full thread 84 ht hexagon head bolts m6x16 mm 85 ht hex bolt m12x50 full thread 86 ht csk bolt m16x65 half thread 87 ht csk allen bolt m16x80full length 88 ht hex bolt m18x80half thread 89 ht csk bolt m20x80mm, full thread 90 ht hex head bolt m20x90half thread 91 ht allen bolt m20x100 half thread 92 ht csk bolt m20x150 half thread 93 ht hex bolt m24x485 half thread 94 ht allen bolt m30x90 half thread 95 ht hex bolt with nut 16x200 half thread 96 csk head screw m20x100 with nut & washer 97 ss bolt m6x40 full thread 98 ss conter sunk head allen boltm8x35 with nut & countersunk washer 99 ms washer m18 100 ht machined washer m12 101 ht machined washer m16 102 ht machined washer m20 103 ht machined washer m24 104 ht machined washer m30 105 hex head bolt m8x30 with nut & 2 no plain washer, full threaded, material –ss 304 106 ss bolt with nut & washer, m16 x100,full threaded, material –ss 304 107 ss bolt m12x100, full threaded , material ss 304 108 ss hex nut, m12, material ss 304 109 ss washer, m12, material ss 304 110 ss bolt with nut & washer, m14 x100,full threaded, material –ss 304 111 ss bolt with nut & washer, m10 x60,full threaded, material –ss 304 112 step stud bolt, size m8 & m6, length –m8x8+m6x6, total length 14mm, material –ss 304 113 ss bolt with nut & washer size:m8x50 (full thread) 114 ss hex head bolt with nutsize: m20x90 (full thread length) 115 ss hex head bolt with nutsize: m20x110 (full thread length) 116 ss hex head bolt with nutsize: m20x145 (full thread length) 117 ss hex head bolt with nutsize: m22x120 (full thread length) 118 ht hex head bolt with nut size: m10x80 (half thread length) 119 ht hex head bolt with nut size: m12x40 (full thread length) 120 ht hex head bolt with nut size: m12x55 full thread length) 121 ht hex head bolt with nut size: m16x60 (full thread length) 122 ht hex head boltsize: m16x85 (full thread) 123 ht hex head bolt with nut size: m20x50 (full thread length) 124 ht hex head bolt with nut size: m20x80 (half thread length) 125 ht hex head bolt with nut size: m20x100 (full thread length) 126 ht hex bolt & nut m20x140spec: alloy steel type of thread : metric standard coarse 127 ht hex bolt & nut m24x140spec: alloy steel type of thread : metric standard coarse 128 ht hex head boltwith nutsize: m27x130 (full thread length) 129 ht hex head bolt with nutsize: m27x145 (full thread length) 130 ht hex head bolt with nutsize: m28x120 (full thread length) 131 ht hex boltm36x200spec: alloy steel type of thread : metric standard coarse 132 ht stud stud with 02 nuts size: m12x75 (full thread) 133 ht stud stud with 02 nuts size: m16x60 (full thread) 134 ht stud stud with 02 nutssize: m16x80 (full thread) 135 ht stud stud with 02 nutssize: m16x100 (full thread) 136 ht stud stud with 02 nuts size: m20x80 (full thread) 137 ht stud with 02 nutssize:m20x110 (full thread length) 138 ht stud with 02 nutssize:m20x140 (full thread length) 139 ht stud with 02 nutssize:m22x90 (full thread length) 140 ht stud with two nuts & 2 washersm30x200spec: alloy steel type of thread : metric standard coarse 141 ht stud with 2 nutm30x300spec: alloy steel type of thread : metric standard coarse 142 ht stud with 2 nutm30x320spec: alloy steel type of thread : metric standard coarse 143 ht stud with 2 nutm40x250spec: alloy steel type of thread : metric standard coarse 144 ht allen bolt (full thread)size : m10x30, spec: alloy steel type of thread : metric standard coarse 145 ht allen bolt (full thread)size : m10x50, spec: alloy steeltype of thread : metric standard coarse 146 ht allen bolt (full thread)size : m12x40, spec: alloy steel type of thread : metric standard coarse 147 ht allen bolt (full thread)size : m12x60, spec: alloy steel type of thread : metric standard coarse 148 ht allen bolt (full thread)size : m16x40, spec: alloy steel type of thread : metric standard coarse 149 ht allen bolt (full thread)size : m16x80, spec: alloy steeltype of thread : metric standard coarse 150 ht hex bolt with nut m36x260, half thread 151 hex head bolt m12x60 with plain washers, full thread, allmaterial ss 304 152 ss hex bolt m12x65,full thread ss 304 ...

Indian Oil Corporation Limited - Haryana

39394406 bids are invited for galvanised steel line pipe as per is 1239 (q3) , sap code 4111100844 pipe, cs, smls, a106, grb, pe, 1 in, xxs, ibr (q3) , sap code 4110110994 pipe, cs, smls, a106, grb, be, 2in, 80 (q3) , sap code 4110111024 pipe, cs, smls, a106, grb, be, 2in, 160 (q3) , sap code 4111111424 pipe, cs, smls, a106, grb, be, 3in, 80, xs, ibr (q3) , sap code 4110121434 pipe, cs, smls, a106, grc, be, 3in, sch160, ibr (q3) , sap code 4110121882 pipe, cs, smls, a106, c, be, 4in, 120, ibr (q3) , sap code 4110122384 pipe, cs, smls, a106, grc, be, 6in, sch160, ibr (q3) , sap code 4110122392 pipe, cs, smls, a106, c, be, 6in, xxs, ibr (q3) , sap code 4111112394 pipe, cs, smls, a106, gr. b, be, 6in, xxs, ibr (q3) , seamless ferritic alloy steel pipe for high temperature service (q3) , seamless, welded and heavy cold worked austenitic stainless steel pipes (q3) , sap code 4148326914 pipe; a358; 304; cl 1; efw; be; 11.13mm, 36in (q3) , sap code 4161080012 pipe, as, smls, b407, unsn08800, 1, be, 2in, 40s (q3) , sap code 4199990892 pipe, cs, dsaw, api5l, gr. b, be, 54in, 0.5in th (q3) , sap code 4110110564 pipe, cs, smls, a106, grb, be, 1in, 40 (q3) , sap code 4126132664 pipe, as, a335, p91, smls, be, 8in, s 120, ibr (q3) total quantity : 3798...

Haryana Power Generation Corporation Limited - Haryana

39343201 tender for pipes & bends 2. alloy steel pipe (seamless) sa 335, of schedule 160, p22, 1½ 60 3. carbon steel pipe (seamless) astm 106 grb of schedule 80, 1 210 4. carbon steel pipe (seamless) astm 106 grb of schedule 80, 1½ 90 5. carbon steel pipe (seamless) astm 106 grb of schedule 80, 2 90 6. carbon steel pipe (seamless)astm 106 grb of schedule 80, 3 30 7. alloy steel (seamless) long bend 90o (r=3d)sa 335, of schedule 80, p22,2 35 8. alloy steel (seamless) long bend 90o (r=3d)sa 335, of schedule 80, p22,1 30 9. alloy steel (seamless) long bend 90deg,schedule 80, size 2 35 10. alloy steel (seamless) long bend 90deg,schedule 160, size 1 35 11. carbon steel(seamless) long bend (r=3d) 90o of schedule 80 astm 106grb, 1½ 30 12. carbon steel(seamless) long bend (r=3d) 90o of schedule 80 astm 106grb, 3 35 13. carbon steel(seamless) long bend (r=3d) 90o of schedule 80 astm 106grb, 2 35 14. carbon steel(seamless) long bend (r=3d) 90o of schedule 80 astm 106grb, 1 40 15. ms pipe (seamless) pipe confirm to is:1239 (part i) 1976 heavy (c class), size 1½ 60 16. ms pipe (seamless) pipe confirm to is:1239 (part i) 1976 heavy (c class), size 2 60...

Irrigation Department - Haryana

39277797 estimate for supply, erection and commissioning of 19 no. eot 5 ton and other allied accessories at various pump houses of siwani canal, jui canal and nigana canal system , supply, erection & commissioning of e.o.t crane tested to 25% overload as per is: 3177& is: 807 completer with di rail type electric wire rope holst confirming to is: 3938, having technical para/meters as under: * capacity 5 metric ton (5000 kgs.) * span of crane as per site requirement. (10 20 mtr.). *bridge construction single girder type construction consisting of r.s. joist of adequate strength, complete with ms square bar 40 mm welded to top flange of the beam (griders) *height of lift 7.0 mtrs± 2 mtrs(approximate) standard lift as per site requirement.*duty class ii (indoor/outdoor type) duty. *electric motors crane duty, tefc squirrel cage induction motor as per is: 325, 5.4 rating suitable for 150 starts per hours with class f insulation and ip: 55 protection, operating on a.c. 3 phase, 50 mz main power supply at 415 ( volts+/ 10%) of bharatbijlee/siemems /abb/cgl make. (1)hosting motors: 3:00hp (2)long travel motor: 1 hp * operating speeds (1)hosting motors: 6 meters: per minute or less (2)long travel motor: 15.0meters: per minute * brakes all motors of the crane shall be coupled to failsafe, a.c. electromagnetic drum/disc type brakes designed to be declutched as soon as power supply is cut/switched off. *gears all gears shall be of helical type precision machine hobbled from tested quality alloy steel dully housed in a totally enclosed dust & vermin proof oil bath lubricated gear boxes. * wire rope tested quality, un galvanized steel wire rope of 6x36 or 6x37 construction with fiber/hemp core as per is 2266 of usha martin make (size 13 mm/4 falls) shall be used. * controls form ground level through a plastic bodied pendant controller sustended from the hoist having control voltage of 110 volts. for safety of the operator complete with (mains) on/off push buttons. *other safety features contractors & overload relay shall be of slemens/bch make, electrical terminals oftecnoplast/phenix/elemax to prevent over hoisting/lowering of the hook block beyond operating limit two way shunt lever type limit switch shall be provided for long travel movement. finally, a c series mcb of mg/hager make shall be provided for mains incoming supply beside individual use protection for all motors. * trailing cables trailing cable, consisting of pvc insulated copper cables complete with cable carrier trolleys running on the section of islf: 50 designation as per approved make by irrigation depatt. with all minor civil work.(for forgaranpura ph 1 rd 46600, garanpura ph 2 rd51050 &garanpura ph 3 rd57300, ph 1,2,3,4 &7 s/c, ph no. 1,2,3,4,5 & ph no.1 kairu , ph rd 28000 gujrani, ph no. 1&2 n/c.)....

Irrigation Department - Haryana

39277724 estimate for supply, erection and commissioning of 9 no. eot 3 ton and other allied accessories at various pump houses of siwani canal, jui canal and nigana canal system , supply, erection & commissioning of e.o.t crane tested to 25% overload as per is: 3177& is: 807 completer with di rail type electric wire rope holst confirming to is: 3938, having technical para / meters as under: * capacity 3 metric ton ( 3000 kgs. ) * span of crane as per site requirement. ( 10 15 mtr. ) . *bridge construction single girder type construction consisting of r.s. joist of adequate strength, complete with ms square bar 40 mm welded to top flange of the beam ( griders ) *height of lift 7.0 mtrs± 2 mtrs ( approximate ) standard lift as per site requirement.*duty class ii ( indoor / outdoor type ) duty. *electric motors crane duty, tefc squirrel cage induction motor as per is: 325, 5.4 rating suitable for 150 starts per hours with class f insulation and ip: 55 protection, operating on a.c. 3 phase, 50 mz main power supply at 415 ( volts+ / 10% ) of bharatbijlee / siemems / abb / cgl make. ( 1 ) hosting motors: 3:00hp ( 2 ) long travel motor: 1 hp * operating speeds ( 1 ) hosting motors: 6 meters: per minute or less ( 2 ) long travel motor: 15.0meters: per minute * brakes all motors of the crane shall be coupled to failsafe, a.c. electromagnetic drum / disc type brakes designed to be declutched as soon as power supply is cut / switched off. *gears all gears shall be of helical type precision machine hobbled from tested quality alloy steel dully housed in a totally enclosed dust & vermin proof oil bath lubricated gear boxes. * wire rope tested quality, un galvanized steel wire rope of 6x36 or 6x37 construction with fiber / hemp core as per is 2266 of usha martin make ( size 13 mm / 4 falls ) shall be used. * controls form ground level through a plastic bodied pendant controller sustended from the hoist having control voltage of 110 volts. for safety of the operator complete with ( mains ) on / off push buttons. *other safety features contractors & overload relay shall be of slemens / bch make, electrical terminals oftecnoplast / phenix / elemax to prevent over hoisting / lowering of the hook block beyond operating limit two way shunt lever type limit switch shall be provided for long travel movement. finally, a c series mcb of mg / hager make shall be provided for mains incoming supply beside individual use protection for all motors. * trailing cables trailing cable, consisting of pvc insulated copper cables complete with cable carrier trolleys running on the section of islf: 50 designation as per approved make by irrigation depatt. with all minor civil work. ( for escape ph no. 1 s / c, kairu ph no. 2, 3, ph no. 3, 4, 5, 8, 9 nigana canal and new sagwan minor....

Haryana Power Generation Corporation Limited - Haryana

38844775 tender for procurement of pipes and bends 1 alloy steel pipe (seamless) sa 335, of schedule 160, p22, 1 2 alloy steel pipe (seamless) sa 335, of schedule 160, p22, 1½ 3 carbon steel pipe (seamless) astm 106 grb of schedule 80, 1 4 carbon steel pipe (seamless) astm 106 grb of schedule 80, 1½ 5 carbon steel pipe (seamless) astm 106 grb of schedule 80, 2 6 carbon steel pipe (seamless) astm 106 grb of schedule 80, 3 7 alloy steel (seamless) long bend 90o (r=3d)sa 335, of schedule 80, p22,2 8 alloy steel (seamless) long bend 90o (r=3d)sa 335, of schedule 80, p22,1 9 alloy steel (seamless) long bend 90deg,schedule 80, size 2 10 alloy steel (seamless) long bend 90deg,schedule 160, size 1 11 carbon steel(seamless) long bend (r=3d) 90o of schedule 80 astm 106grb, 1½ 12 carbon steel(seamless) long bend (r=3d) 90o of schedule 80 astm 106grb, 3 13 carbon steel(seamless) long bend (r=3d) 90o of schedule 80 astm 106grb, 2 14 carbon steel(seamless) long bend (r=3d) 90o of schedule 80 astm 106grb, 1 15 ms pipe (seamless) pipe confirm to is:1239 (part i) 1976 heavy (c class), size 1½ 16 ms pipe (seamless) pipe confirm to is:1239 (part i) 1976 heavy (c class), size 2 ...

Northern Railway - Haryana

38330822 supply of articulated spheroelastic rubber bearingarticulated spheroelastic rubber bearing, articulated spheroelastic rubber bearing as per fasl drawing no. fasl / sb / 0848 for fasl make aar h tight lock coupler for lhb coaches and rdso specification no: rdso / 2011 / cg 03 ( rev 01. ) . make : frontier alloy steels ltd kanpur [ warranty period: 30 months after the date of delivery ] ...

Indian Army - Haryana

38137852 bids are invited for r1 spare handle lh , water temp sensor , seal kit , working light , rear light , handle rh , pressure hose , stainer , pivot pin alloy steel , toe plate , pivot pin , gasket , oil filter , brake piston , break piston seal , hour cable , starter relay , knob , throttle cable , shim kit , brake piston seal , side cutter rh , side cutter lh , hose 08 bsp hp 1910mm a , belt front , bearing liner , starter switch , cable battery ve , gas strut, 700n , hose 10 bsp lp 950m , bolt banjo , air filter , hose 10 bsp hp 700mm , throttle cable assy , cap fuel tank , cable parking break , cap filler breather , break assy , joint universal , tooth bucket , cable battery positive ve , shim 0.5 mm , light headlamp total quantity : 226...

Northern Railway - Haryana

38012300 supply of galvanised alloy steel heavy duty wirerope clamps of size 18 mm [ warranty period: 30 months after the date of delivery ] , galvanised alloy steel heavy duty wirerope clamps of size 16 mm [ warranty period: 30 months after the date of delivery ] , galvanised alloy steel heavy duty wirerope clamps of size 14 mm [ warranty period: 30 months after the date of delivery ] , galvanised alloy steel heavy duty wirerope clamps of size 12 mm [ warranty period: 30 months after the date of delivery ] ...

Engineers India Limited - Haryana

37763664 procurement of heat exchanger carbon steel., heat exchanger low alloy steel., heat exchanger cs las ss clad for bcpl => limited...

Indian Oil Corporation Limited - Haryana

37733435 spares for tyco make psv , list of item(s) / work(s) as per tender documents , m.v soft goods kit,p/n 06.3365.012 , m.v soft goods kit,p/n 06.3365.066 , p.v. soft good kit,p/n 06.2645.004 , m.v soft goods kit,p/n mvkit 443zz12 , p.v. soft good kit,p/n pvkit 400zz p , pilot o ring kit,sa351cf8m,2inx150 , modulator kit,sa351cf8m,2inx150 , p.v soft goods kit, p/n 06.2869.002 , m.v soft goods kit;p/n 06.3365.087 , m.v soft goods kit, p/n 06.3365.017 , p.v soft goods kit, p/n 06.2645.004 , m.v soft goods kit;p/n 06.3365.022 , p.v.soft goods kit,p/n 06.2645.004 , p.v soft goods kit,p/n 06.2869.002 , m.v soft goods kit;p/n 06.3365.083 , mv seat, p/n 02.6151.006 , o ring; kalrez 6375, p/n 05.1065.387 , o ring; kalrez 6375, p/n 05.1065.388 , disc insert,ss316,p/n 145874,73 psv 1901 , alloy stl sprng,p/n x06774a,59 psv 2201a , alloy steel spring, p/n x06872 , alloy steel spring, p/n x06905a , chrome steel spring, p/n x36302 , pv soft goods kit,p/n 06.2645.004 , psv,gasket set,p/n 64962,tyco sanmar , gasket, p/n104217 , gasket, 104343 , gskt;8 1/4odx7 13/16idx1/32 thk,108193 , main vlv softgood kit,p/n 06.3365.014 , gasket set, 108308 b 10, f/ jbs 25 b , gasket set p/n 108315 b 10 , gasket set, 108316 b 10 , gasket set, 108318 b 10 , pv kit p/n 06.2645.118 , gasket set, 108303 b 10 , gasket set, 108304 b 10 , nozzle retainer,6 in, 6r8 , rgasket,44305r68/m,6x8in...

Northern Railway - Haryana

37674589 supply of alloy steel d shackle set of one each ( 1, 3 / 4, 5 / 8, 1 / 2 ) warranty as per irs conditions.load test certificate from government approved lab is to be submitted along with supply ( 1 inch =2.5 ton, 3 / 4 inch =1.25 ton , 5 / 8 inch =0.8 ton, 1 / 2 inch =0.5 ton ) make : sst, iep , rstc or similar [ warranty period: 30 months after the date of delivery ] ...

Haryana Power Generation Corporation Limited - Haryana

37445583 supply pneumatic drain isolating valve , supply pneumatic drain isolating valve note: shut off shall be absolute zero leakage. all valve and attached fitting shall be ibr certified and equivalent , zero passing metal seated ball valve, remote operated with 5 7 kg/cm2 air pressure air to close ( no air to pen) steam drain isolating ball valve with pneumatic actuator, forged alloy steel ( f 22)size: 1.5” class: 3100 pipe diamension: ?48x10 end connection: butt weld , zero passing metal seated ball valve, remote operated with 5 7 kg/cm2 air pressure air to close ( no air to pen) steam drain isolating ball valve with pneumatic actuator, forged alloy steel ( f 22) size: 2” class: 3100 pipe diamension: ?60x11 end connection: butt weld , zero passing metal seated ball valve, remote operated with 5 7 kg/cm2 air pressure air to close ( no air to pen) steam drain isolating ball valve with pneumatic actuator, forged alloy steel ( f 22 size: 1.5” class: 1500 pipe diamension: ?48x5 end connection: butt weld...

National Fertilizers Limited - Haryana

37329397 forged alloy steel gatevalve, matl. conf. to a 182 gr.f22, os and y, rising spindle, stem a 276 tp 410 hardened, ca 15 stellite faced disc and seat ring, socket weld as per ansi b16.11, seal welded bonnet less valve, testing as per api 598 size 1 / 2, 2500 rating ibr , forged alloy steel gate valve, material conf. toa 182 gr. f 22, os and y, seal welded bonnet, rising spindle, stem a 276 tp 410 hardened, ca 15 stellited disc and seat ring, socket weld as per ansi b 16, 11, testing as per api 598, size 1, 2500 rating, ibr => limited...

Indian Oil Corporation Limited - Haryana

37192005 supply of flanges cs_as_ss_cs coated supply of flanges cs_as_ss_cs coated for p25 project at iocl panipat refinery , supply of flange carbon steel , wn flg,cs, 150,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 150,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 150,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 150,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 150,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 150,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 150,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 150,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 150,0, b16.47 ser b, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 150,0, b16.47 ser b, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 150,0, b16.47 ser b, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 150,0, b16.47 ser b, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 150,0, b16.47 ser b, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs (nace), 150,0, b16.47 ser b, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 150,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 150,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 150,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 150,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 150,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs, 150,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 150,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 150,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs (nace), 150,0, b16.47 ser b, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 150,0, b16.47 ser b, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 150,0, b16.47 ser b, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace+h2), 150,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (nace+h2), 150,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (nace), 150,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 150,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 150,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 150,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 150,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs, 150,0, b16.5, bw ends,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 150,0, b16.5, bw ends,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs (nace+h2), 150,0, b16.5, bw ends,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (nace+h2), 150,0, b16.5, bw ends,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (nace), 150,0, b16.5, bw ends,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 150,0, b16.5, bw ends,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs, 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 300,0, b16.47 ser b, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 300,0, b16.47 ser b, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 300,0, b16.47 ser b, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs (nace), 300,0, b16.47 ser b, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace+h2), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (nace+h2), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (nace+h2), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (nace+h2), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (nace+h2), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (h2 ser.), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (h2 ser.), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (h2 ser.), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (h2 ser.), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (h2 ser.), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (h2 ser.), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (nace), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs, 300,0, b16.47 ser b, bw ends,sch 40,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 300,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 300,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 300,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 300,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 300,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 300,0, b16.47 ser b, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs (nace), 300,0, b16.47 ser b, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace+h2), 300,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (nace+h2), 300,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (h2 ser.), 300,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (h2 ser.), 300,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (nace), 300,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 300,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 300,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs, 300,0, b16.5, bw ends,sch non std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 300,0, b16.5, bw ends,sch non std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 300,0, b16.47 ser b, bw ends,sch non std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs (h2 ser.), 300,0, b16.47 ser b, bw ends,sch non std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (nace), 300,0, b16.47 ser b, bw ends,sch non std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 300,0, b16.47 ser b, bw ends,sch non std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 300,0, b16.47 ser b, bw ends,sch non std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 300,0, b16.47 ser b, bw ends,sch non std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 300,0, b16.47 ser b, bw ends,sch non std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 300,0, b16.5, bw ends,sch non std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs, 600,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 600,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 600,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 600,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 600,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs (nace+h2), 600,0, b16.5, bw ends,sch std,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (nace+h2), 600,0, b16.5, bw ends,sch std,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (nace+h2), 600,0, b16.5, bw ends,sch std,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (nace+h2), 600,0, b16.5, bw ends,sch std,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (h2 ser.), 600,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (h2 ser.), 600,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (h2 ser.), 600,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (nace), 600,0, b16.5, bw ends,sch std,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 600,0, b16.5, bw ends,sch std,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs, 600,0, b16.5, bw ends,sch 80,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs (nace+h2), 600,0, b16.5, bw ends,sch 80,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs, 600,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 600,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 600,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 600,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs, 600,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs (nace+h2), 600,0, b16.5, bw ends,sch xs,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (nace+h2), 600,0, b16.5, bw ends,sch xs,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (nace+h2), 600,0, b16.5, bw ends,sch xs,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (nace+h2), 600,0, b16.5, bw ends,sch xs,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (h2 ser.), 600,0, b16.5, bw ends,sch xs,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (h2 ser.), 600,0, b16.5, bw ends,sch xs,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (h2 ser.), 600,0, b16.5, bw ends,sch xs,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (nace), 600,0, b16.5, bw ends,sch xs,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace), 600,0, b16.5, bw ends,sch xs,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , wn flg,cs (nace+h2), 600,0, b16.5, bw ends,sch 120,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs, 600,0, b16.5, bw ends,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs (h2 ser.), 600,0, b16.5, bw ends,sch 160,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (ibr), 150,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 150,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 150,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 150,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 150,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 150,0, b16.47 ser b, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 150,0, b16.47 ser b, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 150,0, b16.5, bw ends,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 300,0, b16.5, bw ends,sch 30,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 300,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 300,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 300,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 300,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 600,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 600,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 600,0, b16.5, bw ends,sch std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 600,0, b16.5, bw ends,sch 60,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 600,0, b16.5, bw ends,sch 80,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 600,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 600,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 600,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 600,0, b16.5, bw ends,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 600,0, b16.5, bw ends,sch non std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 600,0, b16.47 ser b, bw ends,sch non std,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs, 900,0, b16.5, bw ends,sch xs,rtj, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,cs (h2 ser.), 1500,0, b16.5, bw ends,sch 160,rtj, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,cs (ibr), 900,0, b16.5, bw ends,sch 80,rtj, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 900,0, b16.5, bw ends,sch xs,rtj, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 1500,0, b16.5, bw ends,sch xs,rtj, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 1500,0, b16.5, bw ends,sch xs,rtj, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , wn flg,cs (ibr), 1500,0, b16.5, bw ends,sch xs,rtj, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , bf,cs, 150,0, awwa c207 cl.d, ff, flange a516 gr.70, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 150,0, b16.47 ser b, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 150,0, b16.47 ser b, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs (nace+h2), 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (nace+h2), 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (nace+h2), 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (nace+h2), 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (h2 ser.), 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (h2 ser.), 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (nace), 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , bf,cs (nace), 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , bf,cs (nace), 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , bf,cs (nace), 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , bf,cs (nace), 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , bf,cs (nace), 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , bf,cs, 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs (nace+h2), 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (nace+h2), 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (nace+h2), 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (nace+h2), 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (h2 ser.), 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (h2 ser.), 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (h2 ser.), 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (h2 ser.), 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (h2 ser.), 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (h2 ser.), 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (h2 ser.), 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (nace), 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , bf,cs (nace), 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , bf,cs (nace), 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , bf,cs (nace), 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , bf,cs, 600,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 600,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 600,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 600,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs, 600,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs (nace+h2), 600,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (nace+h2), 600,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (nace+h2), 600,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (nace+h2), 600,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (nace+h2), 600,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (h2 ser.), 600,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (h2 ser.), 600,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (h2 ser.), 600,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (h2 ser.), 600,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (h2 ser.), 600,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,cs (nace), 600,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , bf,cs (nace), 600,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , bf,cs (galv.), 150,0, b16.5, ff, flange a105 (galv.), add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs (galv.), 150,0, b16.5, ff, flange a105 (galv.), add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs (galv.), 150,0, b16.5, ff, flange a105 (galv.), add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs (galv.), 150,0, b16.5, ff, flange a105 (galv.), add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs (galv.), 150,0, b16.5, ff, flange a105 (galv.), add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs (galv.), 150,0, b16.5, ff, flange a105 (galv.), add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs (galv.), 150,0, b16.5, ff, flange a105 (galv.), add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,cs (ibr), 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , bf,cs (ibr), 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , bf,cs (ibr), 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , bf,cs (ibr), 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , bf,cs (ibr), 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , bf,cs (ibr), 150,0, b16.47 ser b, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , bf,cs (ibr), 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , bf,cs (ibr), 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , bf,cs (ibr), 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , bf,cs (ibr), 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , bf,cs (ibr), 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , bf,cs (ibr), 300,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , bf,cs (ibr), 600,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , bf,cs (ibr), 600,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , bf,cs (ibr), 600,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , bf,cs (ibr), 600,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , bf,cs (ibr), 600,0, b16.47 ser b, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , threaded flange,cs (galv.), 150,0, b16.5, scrd npt(f) b1.20.1,ff, threaded flange with hub, flange a105 (galv.), add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , threaded flange,cs (galv.), 150,0, b16.5, scrd npt(f) b1.20.1,ff, threaded flange with hub, flange a105 (galv.), add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , threaded flange,cs (galv.), 150,0, b16.5, scrd npt(f) b1.20.1,ff, threaded flange with hub, flange a105 (galv.), add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , threaded flange,cs (galv.), 150,0, b16.5, scrd npt(f) b1.20.1,ff, threaded flange with hub, flange a105 (galv.), add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , threaded flange,cs (galv.), 150,0, b16.5, scrd npt(f) b1.20.1,ff, threaded flange with hub, flange a105 (galv.), add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , threaded flange,cs (galv.), 300,0, b16.5, scrd npt(f) b1.20.1,ff, threaded flange with hub, flange a105 (galv.), add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , steel flg,cs, 150,0, awwa c207 cl.d, ff, hub type, flange a516 gr.70, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , steel flg,cs, 150,0, awwa c207 cl.d, ff, hub type, flange a516 gr.70, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , steel flg,cs, 150,0, awwa c207 cl.d, ff, hub type, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , steel flg,cs, 150,0, awwa c207 cl.d, ff, hub type, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , steel flg,cs, 150,0, awwa c207 cl.d, ff, hub type, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , so flg,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , so flg,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , so flg,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , so flg,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , so flg,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , so flg,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , so flg,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , so flg,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , so flg,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , so flg,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , so flg,cs, 150,0, b16.5, rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , so flg,cs (galv.), 150,0, b16.5, ff, flange a105 (galv.), add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , so flg,cs (galv.), 150,0, b16.5, ff, flange a105 (galv.), add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,cs, 150,0, b16.5, sw end,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,cs, 150,0, b16.5, sw end,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,cs (h2 ser.), 150,0, b16.5, sw end,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs, 150,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,cs, 150,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,cs, 300,0, b16.5, sw end,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,cs, 300,0, b16.5, sw end,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,cs (nace+h2), 300,0, b16.5, sw end,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs (nace+h2), 300,0, b16.5, sw end,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs (h2 ser.), 300,0, b16.5, sw end,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs (h2 ser.), 300,0, b16.5, sw end,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs (nace), 300,0, b16.5, sw end,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , sw flg,cs (nace), 300,0, b16.5, sw end,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , sw flg,cs, 300,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,cs, 300,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,cs (nace+h2), 300,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs (nace+h2), 300,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs (nace+h2), 300,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs (nace+h2), 300,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs (h2 ser.), 300,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs (h2 ser.), 300,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs (nace), 300,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , sw flg,cs (nace), 300,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , sw flg,cs (nace+h2), 300,0, b16.5, sw end,sch xxs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs, 600,0, b16.5, sw end,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,cs, 600,0, b16.5, sw end,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,cs (h2 ser.), 600,0, b16.5, sw end,sch xs,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs (h2 ser.), 600,0, b16.5, sw end,sch xs,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs (nace), 600,0, b16.5, sw end,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , sw flg,cs, 600,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,cs, 600,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,cs, 600,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,cs, 600,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,cs (nace+h2), 600,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs (nace+h2), 600,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs (nace+h2), 600,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs (nace+h2), 600,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs (h2 ser.), 600,0, b16.5, sw end,sch 160,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs (h2 ser.), 600,0, b16.5, sw end,sch 160,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs (h2 ser.), 600,0, b16.5, sw end,sch 160,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs (h2 ser.), 600,0, b16.5, sw end,sch 160,rf, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs (nace+h2), 600,0, b16.5, sw end,sch xxs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs (nace+h2), 600,0, b16.5, sw end,sch xxs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,cs (ibr), 300,0, b16.5, sw end,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , sw flg,cs (ibr), 300,0, b16.5, sw end,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , sw flg,cs (ibr), 300,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , sw flg,cs (ibr), 300,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , sw flg,cs (ibr), 600,0, b16.5, sw end,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , sw flg,cs (ibr), 600,0, b16.5, sw end,sch xs,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , sw flg,cs (ibr), 600,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , sw flg,cs (ibr), 600,0, b16.5, sw end,sch 160,rf, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , supply of flange alloy steel , wn flg,as, 150,0, b16.5, bw ends,sch std,rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 150,0, b16.5, bw ends,sch std,rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 150,0, b16.5, bw ends,sch xs,rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 150,0, b16.5, bw ends,sch 160,rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch std,rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch std,rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch std,rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.47 ser b, bw ends,sch std,rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch xs,rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch xs,rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch xs,rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch xs,rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch xs,rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch non std,rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 600,0, b16.5, bw ends,sch std,rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 150,0, b16.5, bw ends,sch std,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 150,0, b16.5, bw ends,sch std,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 150,0, b16.5, bw ends,sch std,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 150,0, b16.5, bw ends,sch 160,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch std,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch std,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch std,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch std,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch std,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch std,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch std,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch std,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch xs,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch xs,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch xs,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch xs,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch xs,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 300,0, b16.5, bw ends,sch xs,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 600,0, b16.5, bw ends,sch 80,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 600,0, b16.5, bw ends,sch xs,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 600,0, b16.5, bw ends,sch 160,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as (h2 ser.), 300,0, b16.5, bw ends,sch std,rf, normalized & tempered, flange a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,as (h2 ser.), 300,0, b16.5, bw ends,sch std,rf, normalized & tempered, flange a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,as (h2 ser.), 300,0, b16.5, bw ends,sch std,rf, normalized & tempered, flange a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,as (h2 ser.), 300,0, b16.5, bw ends,sch xs,rf, normalized & tempered, flange a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,as (h2 ser.), 300,0, b16.5, bw ends,sch xs,rf, normalized & tempered, flange a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,as (h2 ser.), 300,0, b16.47 ser b, bw ends,sch non std,rf, normalized & tempered, flange a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,as (h2 ser.), 300,0, b16.47 ser b, bw ends,sch non std,rf, normalized & tempered, flange a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,as (nace+h2), 600,0, b16.5, bw ends,sch 60,rf, normalized & tempered, flange a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,as (nace+h2), 600,0, b16.5, bw ends,sch xs,rf, normalized & tempered, flange a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,as (nace+h2), 600,0, b16.5, bw ends,sch xs,rf, normalized & tempered, flange a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,as (nace+h2), 600,0, b16.5, bw ends,sch 160,rf, normalized & tempered, flange a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,as, 900,0, b16.5, bw ends,sch xs,rtj, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as, 900,0, b16.5, bw ends,sch 160,rtj, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,as (h2 ser.), 900,0, b16.5, bw ends,sch std,rtj, normalized & tempered, flange a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wn flg,as (h2 ser.), 1500,0, b16.5, bw ends,sch std,rtj, normalized & tempered, flange a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,as, 150,0, b16.5, rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,as, 150,0, b16.5, rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,as, 300,0, b16.5, rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,as, 300,0, b16.5, rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,as, 300,0, b16.5, rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,as, 150,0, b16.5, rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,as, 300,0, b16.5, rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,as, 300,0, b16.5, rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,as, 300,0, b16.5, rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,as, 300,0, b16.5, rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,as, 300,0, b16.5, rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,as, 600,0, b16.5, rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,as, 600,0, b16.5, rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,as (h2 ser.), 300,0, b16.47 ser b, rf, normalized & tempered, flange a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,as (h2 ser.), 300,0, b16.5, rf, normalized & tempered, flange a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,as (h2 ser.), 300,0, b16.5, rf, normalized & tempered, flange a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,as (nace+h2), 600,0, b16.5, rf, normalized & tempered, flange a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,as (nace+h2), 600,0, b16.5, rf, normalized & tempered, flange a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , bf,as, 900,0, b16.5, rtj, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,as, 300,0, b16.5, sw end,sch xs,rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,as, 300,0, b16.5, sw end,sch xs,rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,as, 300,0, b16.5, sw end,sch 160,rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,as, 300,0, b16.5, sw end,sch 160,rf, flange a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,as, 300,0, b16.5, sw end,sch xs,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,as, 300,0, b16.5, sw end,sch xs,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,as, 300,0, b16.5, sw end,sch 160,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,as, 300,0, b16.5, sw end,sch 160,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,as, 600,0, b16.5, sw end,sch xs,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,as, 600,0, b16.5, sw end,sch 160,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,as, 600,0, b16.5, sw end,sch 160,rf, flange a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,as (h2 ser.), 300,0, b16.5, sw end,sch xs,rf, normalized & tempered, flange a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,as (h2 ser.), 300,0, b16.5, sw end,sch 160,rf, normalized & tempered, flange a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , sw flg,as (h2 ser.), 300,0, b16.5, sw end,sch 160,rf, normalized & tempered, flange a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , supply of flange stainless steel , wn flg,ss,dual, 600,0, b16.5, bw ends,sch 80s,rf, flange a182 gr.f304/304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , wn flg,ss,dual, 600,0, b16.5, bw ends,sch 80s,rf, flange a182 gr.f304/304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , wn flg,ss,dual, 600,0, b16.5, bw ends,sch 80s,rf, flange a182 gr.f304/304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , wn flg,ss, 150,0, b16.5, bw ends,sch 10s,rf, flange a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,ss, 150,0, b16.5, bw ends,sch 40s,rf, flange a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,ss, 150,0, b16.5, bw ends,sch 40s,rf, flange a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,ss, 150,0, b16.5, bw ends,sch 80s,rf, flange a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,ss, 300,0, b16.5, bw ends,sch 10s,rf, flange a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,ss, 300,0, b16.5, bw ends,sch 10s,rf, flange a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,ss, 300,0, b16.5, bw ends,sch 40s,rf, flange a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,ss, 600,0, b16.5, bw ends,sch 40s,rf, flange a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,ss,dual, 150,0, b16.5, bw ends,sch 10s,rf, flange a182 gr.f316/316l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , wn flg,ss,dual, 150,0, b16.5, bw ends,sch 80s,rf, flange a182 gr.f316/316l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , wn flg,ss,dual, 300,0, b16.5, bw ends,sch 10s,rf, flange a182 gr.f316/316l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , wn flg,ss,dual, 300,0, b16.5, bw ends,sch 40s,rf, flange a182 gr.f316/316l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , wn flg,ss, 150,0, b16.5, bw ends,sch 10s,rf, flange a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,ss, 150,0, b16.5, bw ends,sch 10s,rf, flange a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,ss, 150,0, b16.5, bw ends,sch 10s,rf, flange a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,ss, 150,0, b16.5, bw ends,sch 10s,rf, flange a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,ss, 150,0, b16.5, bw ends,sch 40s,rf, flange a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,ss, 150,0, b16.5, bw ends,sch 40s,rf, flange a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,ss, 150,0, b16.5, bw ends,sch 80s,rf, flange a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg,ss, 150,0, b16.5, bw ends,sch 80s,rf, flange a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , wn flg with taper bore,ss, 300,0, b16.5/tkis dwg, bw ends,sch 40s,rf, flange a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.for taper bore sketch and dimension, refer doc. 6745 pip 000 tb 0006 , wn flg,ss,dual, 900,0, b16.5, bw ends,sch 80s,rtj, flange a182 gr.f304/304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , bf,ss,dual, 600,0, b16.5, rf, flange a182 gr.f304/304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , bf,ss,dual, 600,0, b16.5, rf, flange a182 gr.f304/304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , bf,ss,dual, 600,0, b16.5, rf, flange a182 gr.f304/304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , bf,ss, 150,0, b16.5, rf, flange a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,ss, 150,0, b16.5, rf, flange a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,ss, 150,0, b16.5, rf, flange a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,ss, 300,0, b16.5, rf, flange a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,ss,dual, 150,0, b16.5, rf, flange a182 gr.f316/316l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , bf,ss, 150,0, b16.5, rf, flange a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,ss, 150,0, b16.5, rf, flange a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,ss, 150,0, b16.5, rf, flange a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,ss, 150,0, b16.5, rf, flange a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , bf,ss, 300,0, b16.5, rf, flange a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,ss,dual, 600,0, b16.5, sw end,sch 80s,rf, flange a182 gr.f304/304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , sw flg,ss,dual, 600,0, b16.5, sw end,sch 80s,rf, flange a182 gr.f304/304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , sw flg,ss,dual, 600,0, b16.5, sw end,sch 80s,rf, flange a182 gr.f304/304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , sw flg,ss, 300,0, b16.5, sw end,sch 40s,rf, flange a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,ss, 300,0, b16.5, sw end,sch 40s,rf, flange a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,ss, 300,0, b16.5, sw end,sch 80s,rf, flange a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,ss, 300,0, b16.5, sw end,sch 40s,rf, flange a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,ss, 300,0, b16.5, sw end,sch 80s,rf, flange a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,ss, 300,0, b16.5, sw end,sch 80s,rf, flange a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , sw flg,ss, 600,0, b16.5, sw end,sch 80s,rf, flange a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , supply of flange carbon steel(coated) , wn flg,cs,(int epoxy ctd), 150,0, b16.5, bw ends,sch std,rf, forged, internal epoxy coated, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.for internal coating requirements, refer doc. 6745 pip 000 ec 0023 , wn flg,cs,(int epoxy ctd), 150,0, b16.5, bw ends,sch std,rf, forged, internal epoxy coated, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.for internal coating requirements, refer doc. 6745 pip 000 ec 0023 , wn flg,cs,(int epoxy ctd), 150,0, b16.5, bw ends,sch std,rf, forged, internal epoxy coated, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.for internal coating requirements, refer doc. 6745 pip 000 ec 0023 , wn flg,cs,(int epoxy ctd), 150,0, b16.5, bw ends,sch std,rf, forged, internal epoxy coated, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.for internal coating requirements, refer doc. 6745 pip 000 ec 0023 , wn flg,cs,(int epoxy ctd), 150,0, b16.5, bw ends,sch std,rf, forged, internal epoxy coated, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.for internal coating requirements, refer doc. 6745 pip 000 ec 0023 , wn flg,cs,(int epoxy ctd), 150,0, b16.5, bw ends,sch std,rf, forged, internal epoxy coated, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.for internal coating requirements, refer doc. 6745 pip 000 ec 0023 , wn flg,cs,(int epoxy ctd), 150,0, b16.5, bw ends,sch std,rf, forged, internal epoxy coated, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.for internal coating requirements, refer doc. 6745 pip 000 ec 0023 , bf,cs,(int epoxy ctd), 150,0, b16.5, rf, forged, internal epoxy coated, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.for internal coating requirements, refer doc. 6745 pip 000 ec 0023 , bf,cs,(int epoxy ctd), 150,0, b16.5, rf, forged, internal epoxy coated, flange a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.for internal coating requirements, refer doc. 6745 pip 000 ec 0023 => limited...

Department Of Defence Research And Development - Haryana

36974608 supply of screw compressor clamp swivel lower jaw , screw compressor clamp swivel lower jaw , hose clamp is 4762 size 40 mm , hose clamp is 4762 size 50 mm , hose clamp is 4762 size 65 mm , hose clamp is 4762 size 80 mm , hose clamp is 4762 size 130 mm , hose clamp is 4762 size 300 mm , hex socket set 4 mm to 14 mm with ratchet wrench , alloy steel allen key set , tool box as per bhel specs no 47829712482 , torque wrench size 5 desh 35 nm gtw25 or equivalent , adjustable spanners size 12 inchadjustable wrench with high grade cr v plated , adjustable single ended open jaw wench phosphate coating 450 mm , alloy steel screw driver with bits , ratchet handle 3 slash 4 inch drive , double hex socket size 33 mm 3 slash 4 inch drive , double hex socket size 36 mm 3 slash 4 inch drive , double hex socket size 38 mm 3 slash 4 inch drive , double hex socket size 41 mm 3 slash 4 inch drive , double hex socket size 46 mm 3 slash 4 inch drive , double hex socket size 50 mm 3 slash 4 inch drive , fixed base bench vice 8 inch , handsaw 10tpi 500mm , 12 pc double open end spanner high grade chromium vanadium set6x7 8x9 10x11 12x13 14x15 16x17 18x19 20x22 21x23 24x27 25x28 30x32 mm , double headed ring spanner size 36mmx41mm is 2029 , hand hacksaw frame for blade size 300x25x0 point 63 mm , hand hacksaw blade carbon steel double side cutting 24tpi size 300 x 25 x 0 point 63 mm , corded angle grinder for disc dia 125 mm , al oxide natural stone grinder wheel 125 mm , hss drill bit set 0 point 3 mm to 18 mm 12 piece , soild carbide drill cutting dia 3mm length 58 mm , soild carbide drill cutting dia 5mm length 62 mm , soild carbide drill cutting dia 11.5mm length 142 mm , hydraulic toe jack 5 ton capacity , 3 jaw hardened steel puller 6 inch , 3 jaw cr v steel puller 8 inch , pipe wrench nominal size 350 mm , pipe wrench nominal size 450 mm , combination pliers 160 mm length , plier long nose length 165 mm plastic insulated handle , circlip plier straight handle length 125 mm plastic insulated handle , circlip plier flared handle bent nose type a length 175 mm plastic insulated handle , circlip plier straight handle internal straight nose length 230 mm plastic insulated handle , circlip plier straight handle bent nose type a length 220 mm plastic insulated handle , circlip plier bowed handle external straight nose length 175mm plastic insulated handle , hand operated pneumatic barrel pump for 200 lit barrel , corded brushed handheld electric drill , lcd display vernier calipers 0 to 300 mm , lcd display vernier calipers 0 to 500 mm , synthetic rubber based adhesive 50 ml , cyanoacrylate adhesive 20 gm , 3 point 5 digit lcd rms clamp meter , hdpe tripal tarpauline 200gsm size 5m x 5m , hdpe tripal tarpauline 200gsm size 7 point 5m x 5 point 5m , cased measuring tape 10 m , cased measuring tape 20 m , nitrile rubber gloves , single ended open jaw wrench spanner size 41 mm , single ended open jaw wrench spanner size 46 mm , single ended open jaw wrench spanner size 50 mm , single ended open jaw wrench spanner size 55 mm , single ended open jaw wrench spanner size 60 mm...

Panchayat Raj Department - Haryana

36911549 tender for purchase of machines / appratus for gym at village garhi sampla 1 purchase of machinesappratus for gym at village garhi sampla 2 10 heavy dumbells stand/rackin double platform (made up of mainly olympic rectangular pipe of 4’ x2’ approx.: more nearest to approx.2o9x81x83 cm with 2.15mm thickness, with angleiron welded with flat patti with rubber pasted on whichdumbbell srestonit,two platform/ shelves) 3 12 cycle : adjustable height and comfortable seat with cushions to prevent back aches and muscle stiffness.8 adjustable reslstance levels and tension controller knob. material alloy steel. 6 months warranty. size (l’b*h) (41*24*46) incites.dual actlon mode stationary and movlng handles both. full body workout arms, calves, chest and back.belt based resistance mechan lsm allows better momentum based recovery and better pedalllng technlque.suitable for hlgh intensity cardia workout, weight loss, full body workout and strength trainlng. 4 7 superior olympic bench decline : (made up of malnly olymplc rectangular pipe ol 4‘ x2’ approx.: more nearest to approx.2 10x1g6x137 cm wlth 2.15mm tl›lctness, heavy cushion padding on12 mm plys wlh specla1 non abraslve fabrlc non tearing fabrlc. with two vertical plpes have clampfor resting rod on it, used for dolng decline level pattern chest press at one fixed decline level wlth leg locking) 5 8 spare flat bench for dumbbell fly exercise : (made up of mainly olymplc rectangular pipe of 4’ x2’ approx.: more nearest to approx12 1x7sx46 cm with 2.15mm thickness, heavy cushion padding on12mm plys wth special non abrasive fabric non tearing fabric.) 6 arm wheel: provldlng, deslgnlng and flxlng arm wheel in a palr of slre 850 x 800 x 7 dumble 25o kg. (20,15,10.5.2.5)made from high quality rubbertear proef, soundless and bouncy effht. 8 functional 7raineit mechint : all pipes made ‹ip size 2” x4“ ol hot rolled hollow rectangular ms plpe wiih ›i e 153s 100s zzo cm anti powder coä ted u slng akzo nobel or pqtiiv,aient of 80 1 20 n›icron tljlck. all welrllng jolnts of plpe are well‹velrled with jolnts scalloprd as necessary and dressed olf removingshaip edges and burrs. zlnc primer pain[ to be applied at all weldlng points prior to finishing. handle bars are to be provided with high qualit y grip rubber. padals shall be made up of nylon alloy with rounded edge ol prevent any impact of in¡ury and seat to be made from virgin ltdpe mant›facturcd by rotalional moulding with minimumthickness of plastic 4.00mm, colourful and u v resistant environmentalfriendly. ßearing used shall be malntenance free, duly olled sealed and self lubricated made by reputed company to be approved by englneer in charge. equipmenl to be fitted within built llmiters to prevent unwanel movements. all open ends al pipe to be coloured by gi/llope caps for user safety. the equipment to be fixed on ground with concrete of minimum strength m25 and j shaped welded bolts and once the concrete is set, fix the equlpment on to it and cover nutsand bolts with the base plate cover, all complete as per direction and approval of engineer in charge regardlng material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc. 9 heaw olympic weight plates stand/rack in tree shape : (made up of mainly olympic rectangular pipe of 4` x2` approx.: more nearest to approx.96x63x120 cm wlth 2.15mm thickness, with 6 round pipes welded ( 3 pipes on each side)on which weigh plates are hanged/holded) 10 multy gym six station (leg pull, leg curl with leg extension, biceps with trlceps, pec dee fly): consists of 4 weighted stations and z light stations: and it is«omhinalion of 8 type of excerslce thls is macle up of mainly olympic rectangular pipe of 4’ x2’ with 2.15mm thickness with steel twisted wire with pvc/nyioncoated cable5mm 6mm: with pvc coated weight plates for noiseless working/movements, weight plates stack moves/slides in stainless steel pipes for smooth and noiseless movement throughout lifespan of equipments, ball bearing mouted fibre/pvcpullys, heavy ct›shionpadding on 12mm plys with special non abrasive fabric nontearing tauric.each weight stackis 7skg sheavy. 11 plates 250kg made from high quality rubber tear proof 12 providing, designing and fixing leg press size 153x137x152 cm fabricated with 2“x4” rectangular hollow pipe with 3.00 mm thick and powder coated using akzo nobel or equivalent ofg0 120 micron thick. allweldingjointsofpipearewellwelded withjoints scalloped as necessary and dressed off removing sharp edges and burrs. zinc primer palnt to be applied at all welding points prior to finishing. handle bars are to be pravided with high quality grip rubber at top end. padals shall be made up of nylon alloy withroundededge of prevent any impact of injury and seat to be made from virgin lldpe manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and u v resistant environmental friendly.bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by engineer in charge. equipment to be fitted wlthin built limiters to prevent unwanted movements. all open ends of pipe to be coloured by gi/lldpe caps for user safety. the equipmentto befixed onground withconcreteof minimum strength m2sand j shaped welded bolts and once the concrete is set, flx the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of engineer in charge regarding material, shape of equipment, colour on metal, seat and basecover plate and0xlng of equipment etc 13 rod stand 14 rods 7f/3 and 3f/2 =27f 15 seated chest press : dimensiuns : 170x120x166.frame structures : over sized internal frame tubing of hlgh tensile strength stnel, gracefully curved continuous welded, factory assembled weight frame. name of tube : oval tubing.tube size : 1z2 mm x 58 mm. tube gauge : 4 mm.welght stack : 80 kgs. 16 superior olympic 8ench incline : (madu up ol mainly olympic rectangular pipe of 4’ x2’ approx.: mure ‹dearest to approx. t63x165x137 cm wilh 2.15mm thickness, heavy cull iur› j›addinj: on 12mm plys with special non abrasive labric non luaiing fakrlc, with two vertical pipes have clamp forr‹`siing rodortit,u›e‹j for dolng incline level pattern› chest press at orje lix0d inclinu il`vl`i). 17 superior olympic bench flat : (made up of mainly olympic rectangular pipe of 4‘ x2‘ approx. : more nearest to approx. 170 x t68x137 cm with 2.15mm thlckness, heavy cusf›iurj padding un 12mm plys wth special non abrasive fabrlc non sparing fahric. wilh two vertical pipes have clamp forrestlng rodonlt, used for doing flatpattern cl estpiessac one f ixed level) ...

Indian Oil Corporation Limited - Haryana

36711330 supply of fitting block forged carbon steel_alloy steel_stainless steel supply of fitting block forged carbon steel_alloy steel_stainless steel for p25 project at iocl panipat refinery , supply of fitting block forged carbon steel , flat weldolet, cs, sp 97 / mfr. std, bw end, sch xs, flat weldolet suitable for use, at cap, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.other dimensions as per bonney forge, or equivalent , flat weldolet, cs ( ibr ) , sp 97 / mfr. std, bw end, sch 160, flat weldolet suitable for use, at cap, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required, 3.other dimensions as per bonney forge, or equivalent , elb, 90 deg, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 90 deg, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 90 deg, cs ( nace+h2 ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 90 deg, cs ( nace+h2 ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 90 deg, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 90 deg, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 90 deg, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , elb, 90 deg, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , elb, 90 deg, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 90 deg, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 90 deg, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 90 deg, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 90 deg, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 90 deg, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 90 deg, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 90 deg, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 90 deg, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 90 deg, cs ( nace ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , elb, 90 deg, cs ( nace ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , elb, 90 deg, cs, 9000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 90 deg, cs ( nace+h2 ) , 9000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 90 deg, cs ( ibr ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , elb, 90 deg, cs ( ibr ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , elb, 90 deg, cs ( ibr ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , elb, 45 deg, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 45 deg, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 45 deg, cs ( nace+h2 ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 45 deg, cs ( nace+h2 ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 45 deg, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 45 deg, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 45 deg, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , elb, 45 deg, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , elb, 45 deg, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 45 deg, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 45 deg, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 45 deg, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 45 deg, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 45 deg, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 45 deg, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 45 deg, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 45 deg, cs ( nace ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , elb, 45 deg, cs, 9000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 45 deg, cs ( nace+h2 ) , 9000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 45 deg, cs ( ibr ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , elb, 45 deg, cs ( ibr ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , elb, 45 deg, cs ( ibr ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , fcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , fcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , fcpl, cs ( nace+h2 ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , fcpl, cs ( nace+h2 ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , fcpl, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , fcpl, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , fcpl, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , fcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , fcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , fcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , fcpl, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , fcpl, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , fcpl, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , fcpl, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , fcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , fcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , fcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , fcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , fcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , fcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , fcpl, cs ( nace+h2 ) , 9000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , fcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , fcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , fcpl, cs ( ibr ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , fcpl, cs ( ibr ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , rcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , rcpl, cs ( nace+h2 ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , rcpl, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , rcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , rcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , rcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , rcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , rcpl, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , rcpl, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , rcpl, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , rcpl, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , rcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , rcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , rcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , rcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , rcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , rcpl, cs, 9000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , rcpl, cs ( nace+h2 ) , 9000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , rcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , rcpl, cs ( ibr ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , rcpl, cs ( ibr ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , tee, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs ( nace+h2 ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , tee, cs ( nace+h2 ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , tee, cs ( nace+h2 ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , tee, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , tee, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , tee, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , tee, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , tee, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , tee, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , tee, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , tee, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , tee, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , tee, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , tee, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , tee, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , tee, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , tee, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , tee, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , tee, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , tee, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , tee, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , tee, cs ( nace ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , tee, cs ( nace ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , tee, cs ( nace+h2 ) , 9000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , tee, cs ( nace+h2 ) , 9000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , tee, cs ( ibr ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , tee, cs ( ibr ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , tee, cs ( ibr ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , tee, cs ( ibr ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , tee, cs ( ibr ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , tee, cs ( ibr ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , tee, cs ( ibr ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs ( nace+h2 ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( nace+h2 ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( nace+h2 ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 3000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs, 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( nace+h2 ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , hcpl, cs ( nace+h2 ) , 9000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( nace+h2 ) , 9000, 0, b16.11, sw ends, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, cs ( galv ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 3000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , hcpl, cs ( ibr ) , 6000, 0, b16.11, sw ends, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , nipple, cs, 100mm ( nace ) , b36.10m, pe x pe, sch 160, seamless, both ends pe, length = 100 mm, nipple a106 gr.b, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , elb, 90 deg, lr, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 90 deg, lr, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 90 deg, lr, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 90 deg, lr, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 90 deg, lr, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 90 deg, lr, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 45 deg, lr, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 45 deg, lr, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 45 deg, lr, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 45 deg, lr, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 45 deg, lr, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 45 deg, lr, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , cap, cs, 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , cap, cs, 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , cap, cs ( nace+h2 ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , cap, cs ( h2 ser. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , cap, cs ( nace ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , cap, cs, 6000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , cap, cs ( h2 ser. ) , 6000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , cap, cs ( nace ) , 6000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005 , cap, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , cap, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , cap, cs ( ibr ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , cap, cs ( ibr ) , 6000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105n, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.ibr certificate in form iiic required , fcpl, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , fcpl, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , fcpl, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , fcpl, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , fcpl, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , fcpl, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, cs ( galv. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , swage nipples, conc, cs ( galv. ) , 3000, 0, bs 3799, scrd npt ( m ) b1.20.1, forged, threaded ends ( mnpt ) , lengthas per bs 3799, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , swage nipples, conc, cs ( galv. ) , 3000, 0, bs 3799, scrd npt ( m ) b1.20.1, forged, threaded ends ( mnpt ) , lengthas per bs 3799, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , swage nipples, conc, cs ( galv. ) , 3000, 0, bs 3799, scrd npt ( m ) b1.20.1, forged, threaded ends ( mnpt ) , lengthas per bs 3799, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , swage nipples, conc, cs ( galv. ) , 3000, 0, bs 3799, scrd npt ( m ) b1.20.1, forged, threaded ends ( mnpt ) , lengthas per bs 3799, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , swage nipples, conc, cs ( galv. ) , 3000, 0, bs 3799, scrd npt ( m ) b1.20.1, forged, threaded ends ( mnpt ) , lengthas per bs 3799, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , swage nipples, conc, cs ( galv. ) , 3000, 0, bs 3799, scrd npt ( m ) b1.20.1, forged, threaded ends ( mnpt ) , lengthas per bs 3799, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , swage nipples, conc, cs ( galv. ) , 3000, 0, bs 3799, scrd npt ( m ) b1.20.1, forged, threaded ends ( mnpt ) , lengthas per bs 3799, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , swage nipples, ecc, cs ( galv. ) , 3000, 0, bs 3799, scrd npt ( m ) b1.20.1, forged, threaded ends ( mnpt ) , lengthas per bs 3799, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , swage nipples, ecc, cs ( galv. ) , 3000, 0, bs 3799, scrd npt ( m ) b1.20.1, forged, threaded ends ( mnpt ) , lengthas per bs 3799, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , swage nipples, ecc, cs ( galv. ) , 3000, 0, bs 3799, scrd npt ( m ) b1.20.1, forged, threaded ends ( mnpt ) , lengthas per bs 3799, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , swage nipples, ecc, cs ( galv. ) , 3000, 0, bs 3799, scrd npt ( m ) b1.20.1, forged, threaded ends ( mnpt ) , lengthas per bs 3799, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , swage nipples, ecc, cs ( galv. ) , 3000, 0, bs 3799, scrd npt ( m ) b1.20.1, forged, threaded ends ( mnpt ) , lengthas per bs 3799, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , swage nipples, ecc, cs ( galv. ) , 3000, 0, bs 3799, scrd npt ( m ) b1.20.1, forged, threaded ends ( mnpt ) , lengthas per bs 3799, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , swage nipples, ecc, cs ( galv. ) , 3000, 0, bs 3799, scrd npt ( m ) b1.20.1, forged, threaded ends ( mnpt ) , lengthas per bs 3799, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , swage nipples, ecc, cs ( galv. ) , 3000, 0, bs 3799, scrd npt ( m ) b1.20.1, forged, threaded ends ( mnpt ) , lengthas per bs 3799, a105 ( galv. ) , add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , supply of fitting block forged alloy steel , wlet, as ( nace+h2 ) , mss sp 97, bw ends, sch xs, forged, normalized & tempered, a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wlet, as ( nace+h2 ) , mss sp 97, bw ends, sch 160, forged, normalized & tempered, a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , wlet, as ( nace+h2 ) , mss sp 97, bw ends, sch 160, forged, normalized & tempered, a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.nace req. acc. to nace mr 0103, and doc. 6745 pip 000 ec 0005, 3.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 90 deg, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 90 deg, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 90 deg, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 90 deg, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 90 deg, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 90 deg, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 90 deg, as ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, normalized & tempered, a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 90 deg, as ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, normalized & tempered, a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 90 deg, as ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, normalized & tempered, a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , elb, 45 deg, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 45 deg, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 45 deg, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 45 deg, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , fcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , fcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , fcpl, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , fcpl, as ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, normalized & tempered, a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , fcpl, as ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, normalized & tempered, a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , rcpl, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , rcpl, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , rcpl, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , rcpl, as ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, normalized & tempered, a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , tee, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, as ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, normalized & tempered, a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 3000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as, 6000, 0, b16.11, sw ends, forged, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, as ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, normalized & tempered, a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, as ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, normalized & tempered, a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, as ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, normalized & tempered, a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, as ( h2 ser. ) , 3000, 0, b16.11, sw ends, forged, normalized & tempered, a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, as ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, normalized & tempered, a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, as ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, normalized & tempered, a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, as ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, normalized & tempered, a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, as ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, normalized & tempered, a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, as ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, normalized & tempered, a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , hcpl, as ( h2 ser. ) , 6000, 0, b16.11, sw ends, forged, normalized & tempered, a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , cap, as, 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, normalized & tempered, a182 gr.f5, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , cap, as, 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, normalized & tempered, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , cap, as, 6000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, normalized & tempered, a182 gr.f9, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , cap, as ( h2 ser. ) , 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, normalized & tempered, a182 gr.f11 cl.2, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2.additional requirements for h2 service, acc. to doc. 6745 pip 000 ec 0004 , supply of fitting block forged stainless steel , elb, 90 deg, ss, dual, 3000, 0, b16.11, sw ends, forged, a182 gr.f304 / 304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , elb, 90 deg, ss, dual, 3000, 0, b16.11, sw ends, forged, a182 gr.f304 / 304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , elb, 90 deg, ss, dual, 3000, 0, b16.11, sw ends, forged, a182 gr.f304 / 304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , elb, 90 deg, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 90 deg, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 90 deg, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 90 deg, ss, dual, 3000, 0, b16.11, sw ends, forged, a182 gr.f316 / 316l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , elb, 90 deg, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 90 deg, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 90 deg, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 90 deg, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 45 deg, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 45 deg, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , elb, 45 deg, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , cap, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , fcpl, ss, dual, 3000, 0, b16.11, sw ends, forged, a182 gr.f304 / 304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , fcpl, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , fcpl, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , fcpl, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , fcpl, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , fcpl, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , fcpl, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , rcpl, ss, dual, 3000, 0, b16.11, sw ends, forged, a182 gr.f304 / 304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , rcpl, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , rcpl, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, ss, dual, 3000, 0, b16.11, sw ends, forged, a182 gr.f304 / 304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , tee, ss, dual, 3000, 0, b16.11, sw ends, forged, a182 gr.f304 / 304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , tee, ss, dual, 3000, 0, b16.11, sw ends, forged, a182 gr.f304 / 304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , tee, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, ss, dual, 3000, 0, b16.11, sw ends, forged, a182 gr.f316 / 316l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , tee, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , tee, ss, 3000, 0, b16.11, sw ends, forged, a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, ss, dual, 3000, 0, b16.11, sw ends, a182 gr.f304 / 304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , hcpl, ss, dual, 3000, 0, b16.11, sw ends, a182 gr.f304 / 304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , hcpl, ss, dual, 3000, 0, b16.11, sw ends, a182 gr.f304 / 304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , hcpl, ss, dual, 3000, 0, b16.11, sw ends, a182 gr.f304 / 304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , hcpl, ss, 3000, 0, b16.11, sw ends, a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, ss, 3000, 0, b16.11, sw ends, a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, ss, 3000, 0, b16.11, sw ends, a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, ss, dual, 3000, 0, b16.11, sw ends, a182 gr.316 / 316l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , hcpl, ss, dual, 3000, 0, b16.11, sw ends, a182 gr.316 / 316l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , hcpl, ss, 3000, 0, b16.11, sw ends, a182 gr.316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, ss, 3000, 0, b16.11, sw ends, a182 gr.316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, ss, 3000, 0, b16.11, sw ends, a182 gr.316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, ss, 3000, 0, b16.11, sw ends, a182 gr.316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , hcpl, ss, 3000, 0, b16.11, sw ends, a182 gr.316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , cap, ss, dual, 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a182 gr.f304 / 304l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , cap, ss, 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a182 gr.f304, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , cap, ss, dual, 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a182 gr.f316 / 316l, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001, 2. shall be dual certified , cap, ss, 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , cap, ss, 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , fcpl, ss, 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 , fcpl, ss, 3000, 0, b16.11, scrd npt ( f ) b1.20.1, forged, a182 gr.f316, add. information, 1.for general technical requirements, refer doc. 6745 pip 000 ec 0001 => limited...

Indian Oil Corporation Limited - Haryana

36318894 tyco make psv spares for pta , list of item ( s ) / work ( s ) as per tender documents , alloy steel spring, p / n x06745 , alloy steel spring, p / n x06880 , alloy steel spring, p / n x06919a , bell&tailpiece assy, p / n s97958 , bell&tailpiece assy, p / n s97964 , disc holder, p / n 146381 118 , disc holder, p / n 147154 118 , disc insert stelited, p / n 0p8310 igc , disc insert stellited, p / n 0p8387 igc , disc insert stellited, p / n 151455 igc , disc insert, p / n:148436 , disc insert, p / n 153123 igc , disc insert, p / n 153722 igc , gasket p / n 108303 d , gasket p / n 108305 e , gasket p / n 108316 e 10 , gasket p / n 108317 a 10 , gasket p / n 108317 d 10 , gasket, p / n 147180 , gasket, p / n 147181 , gasket, p / n 147182 , gasket, p / n 147183 , gasket, p / n 147184 , gasket, p / n 147186 , gasket, p / n 147187 , gasket, p / n 147188 , gasket, p / n 147194 , nozzle, p / n:128124 118 , nozzle, p / n 125999 118 , spindle assy, p / n:s66303 , spindle assy, p / n s58913 , spindle assy, p / n s58914 , spindle assy, p / n s60668 , spindle assy, p / n s64738 , spindle assy, p / n s65212 , spindle assy, p / n s65230 , spindle assy, p / n s66774 , spindle assy, p / n s66916 , spindle assy, p / n s68012 , spindle assy, p / n s68952 , spindle assy, p / n s71148 , spindle assy, p / n s71861 , spindle assy, p / n s74206 , spindle point assy, p / n:s66316 , spring washer, p / n 103200 , spring washer, p / n 103478 , spring washer, p / n 104198 , ss316 spring, p / n x07404...

Department Of Fertilizers - Haryana

36300295 bids are invited for forged alloy steel gate valve 2500 rating half inch with ibr , forged alloy steel gate valve 2500 rating 1 inch with ibr mse total quantity : 20...

Panchayat Raj Department - Haryana

36085591 tender for bahiya installation of zym material at village bahiya block rania superior olympic bench flat ( made up of mainly olympic rectangular pipe of 4`x2`` approx.: more nearest to approx. 170x168x137 cm with 2.15mm thickness, heavy cushion padding on 12mm plys with special non abrasive fabric non tearing fabric. with two vertical pipes have clamp forresting rodonit, used for doing flatpattern chestpressat one fixed level ) ` 2 `superior olympic bench incline ( made up of mainly olympic rectangular pipe of 4`x2` approx.: more nearest to approx. 163x165x137 cm with 2.15mm thickness, heavy cushion padding on 12mm plys with special non abrasive fabric non tearing fabric. with two vertical pipes have clamp forresting robonit, used for doing incline level pattern chest press at one fixed incline level ) . ` 3 arm wheel: providing, designing and fixing arm wheel in a pair of size 850x800x1800mm 4 heavy dumbells stand / rackin double platform: ( made up of mainly olympic rectangular pipe of 4’x2’ appox, : more nearest to approx.. 209x81x83 cm with 2.15mm thickness , with angleiron welded with flat patti with rubber pasted on which dumbbell srestonint, two platform / shelves ) 5 providing, designing and fixing leg press size 153x137x152 cm fabricated with 2`x4` rectangular hollow pipe with 3.00 mm thick and powder coated using akzo nobel or equivalent of 80 120 micron thick. all welding joints of pipe are well welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. zinc primer paint to be applied at all weldings points prior to finishing. handle bars are to be provided with high quality grip rubber at top end. padals shall be made upto of nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin lldpe manufactured by rotational moulding with minimum thickness of plastic 4.00 mm , colourful and u v resistant environmental friendly, bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by engineer in charge. equipment to be fitted within built limiters to prevent unwanted movements. all open ends of pipe to be coloured by gi / lldpe caps for user safety. the equipment to be fixed on ground with concrete of minimum strength m25 and j shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of engineer in charge regarding material, shape of equipment, colour on metal, seat and basecover plaste and fixing of equipment etc. 6 seated chest press: dimensions: 170x120x66, frame structures:over sized internal frame tubing of high tensile strength steel, gracefully curved continuous welded, factory assembled weight frame. name of tube: oval tubing tube size: 122mm x 58mm tube gauge: 4mm 7 spare flat bench for dumbbell fly exercise: ( made up of mainly olympic rectangular pipe of 4’x2’ approx, ” more nearest to approx. 121x75x46 cm with 2.15 mm thickness. heavy cushion padding on 12mm plys with special non abrasive fabric non tearing fabric ) 8 superior olympic bench decline: ( made up of mainly olympic rectangular pipe of 4’ x 2’ approx.: more nearest to approx.. 210x166x137cm with 2.15mm thickness, heavy cushion padding on 12mm plys with special non abrasive fabric non tering fabric. with two vertical pipes have clampfor resting rod on it, used for doing decline level pattern chest press at one fixed decline level with leg locking 9 twister: providing designing and fixing twister of size 1700x1300x1300 mm fabricated 2”x4” rectangular hellow ms pipe and powder coated using. akzo nobel or equivalent of 80 120 micron thick . all welding joint of ipe are well welded with joints scalloped as necessary and dressed off removing sharp edge and burrs. 10 cycle adjustable height and comfortable seat with cushions to prevent back aches and muscle stiffness. 8 adjustable resistance levels and tension controller knob. material alloy steel. 6 months warranty. size ( l*b*h* ) ( 41*24*6 ) inches. dual action mode stationary and moving handles both. full body workout arms, calves, chest and back. belt based resistance mechanism allows better, momentum based recovery and better pedalling technique. suitable for high intensity cardio workout, weight loss, fully body workout and strangth training. 11 push up bar: pipe dimension – main post 140mm dia and other post 40mm dia. all joint shell be lubricated made by reputed company to be approved by engineer in charge. equipment to be fitted within built limiters to prevent unwanted movements. all open ends of pipe to be coloured by gi / lldpe caps for user safety. 12 plates 250 kg ( 20, 15, 10, 5, 2, 5 ) made from high quality rubber, tear proof, soundless and bouncy effect 13 rods7f / 3 and 3f / 2 = 27...

Haryana Power Generation Corporation Limited - Haryana

36027707 for supply of emergency drain control valve of hph 7and8 , high pressure heater (hph 7) emergency drain control valve application: high pressure heater (hph 7) emergency drain control valve, size:4 body style globe, mass flow rate liquid (wi) 171540 kg/h, temperatureratings for standard classastm a217 grade wc9 valves (in accordance with asme b16.34) rating cl900, body wc9 alloy steel, end connection butt welded sch 80, cage: sst, seat ring: sst valve plug: sst, equal percentage flow characteristic, equal percentage cage, hydrodynamic trim valve lpa (lpae1m) <85db(a), push down to close, cl5 leakage, shutoff class ansi cl v, pneumatic actuator push down to close & 75 psi maximum casing press, smart positioner, air fail to open, handwheel handwheel for manual operation. working parameters: valve inlet pressure & temp:4.81mpa & 265 deg c, valve outlet pressure: under vacuum 0.92bar , high pressure heater (hph 8) emergency drain control valve application: high pressure heate...

Department Of Defence Research And Development - Haryana

36011656 supply of screw compressor clamp swivel lower jaw , screw compressor clamp swivel lower jaw , hose clamp is 4762 size 40 mm , hose clamp is 4762 size 50 mm , hose clamp is 4762 size 65 mm , hose clamp is 4762 size 80 mm , hose clamp is 4762 size 130 mm , hose clamp is 4762 size 300 mm , hex socket set 4 mm to 14 mm with ratchet wrench , alloy steel allen key set , tool box as per bhel specs no 47829712482 , torque wrench size 5 desh 35 nm gtw25 or equivalent , adjustable spanners size 12 inchadjustable wrench with high grade cr v plated , adjustable single ended open jaw wench phosphate coating 450 mm , alloy steel screw driver with bits , ratchet handle 3 slash 4 inch drive , double hex socket size 33 mm 3 slash 4 inch drive , double hex socket size 36 mm 3 slash 4 inch drive , double hex socket size 38 mm 3 slash 4 inch drive , double hex socket size 41 mm 3 slash 4 inch drive , double hex socket size 46 mm 3 slash 4 inch drive , double hex socket size 50 mm 3 slash 4 inch drive , fixed base bench vice 8 inch , handsaw 10tpi 500mm , 12 pc double open end spanner high grade chromium vanadium set6x7 8x9 10x11 12x13 14x15 16x17 18x19 20x22 21x23 24x27 25x28 30x32 mm , double headed ring spanner size 36mmx41mm is 2029 , hand hacksaw frame for blade size 300x25x0 point 63 mm , hand hacksaw blade carbon steel double side cutting 24tpi size 300 x 25 x 0 point 63 mm , corded angle grinder for disc dia 125 mm , al oxide natural stone grinder wheel 125 mm , hss drill bit set 0 point 3 mm to 18 mm 12 piece , soild carbide drill cutting dia 3mm length 58 mm , soild carbide drill cutting dia 5mm length 62 mm , soild carbide drill cutting dia 11.5mm length 142 mm , hydraulic toe jack 5 ton capacity , 3 jaw hardened steel puller 6 inch , 3 jaw cr v steel puller 8 inch , pipe wrench nominal size 350 mm , pipe wrench nominal size 450 mm , combination pliers 160 mm length , plier long nose length 165 mm plastic insulated handle , circlip plier straight handle length 125 mm plastic insulated handle , circlip plier flared handle bent nose type a length 175 mm plastic insulated handle , circlip plier straight handle internal straight nose length 230 mm plastic insulated handle , circlip plier straight handle bent nose type a length 220 mm plastic insulated handle , circlip plier bowed handle external straight nose length 175mm plastic insulated handle , hand operated pneumatic barrel pump for 200 lit barrel , corded brushed handheld electric drill , lcd display vernier calipers 0 to 300 mm , lcd display vernier calipers 0 to 500 mm , synthetic rubber based adhesive 50 ml , cyanoacrylate adhesive 20 gm , 3 point 5 digit lcd rms clamp meter , hdpe tripal tarpauline 200gsm size 5m x 5m , hdpe tripal tarpauline 200gsm size 7 point 5m x 5 point 5m , cased measuring tape 10 m , cased measuring tape 20 m , nitrile rubber gloves , single ended open jaw wrench spanner size 41 mm , single ended open jaw wrench spanner size 46 mm , single ended open jaw wrench spanner size 50 mm , single ended open jaw wrench spanner size 55 mm , single ended open jaw wrench spanner size 60 mm...

Haryana Power Generation Corporation Limited - Haryana

35916913 supply of pneumatic and manual isolation valves , zero passing integrated metal seated ball valve. remote operated with 5 7 kg air pressure air to close ( no air to open ) pneumatic steam drain isolation ball valve with pneumatic actuator, forged alloy steel ( f22 ) , press ( bar ) & temp ( °c ) : 180 & 540, pipedimension & connection:ø48x10sw, class :4500, size:1.5 , zero passing integrated metal seated manual ball valve. forged alloy steel ( f22 ) , press ( bar ) & temp ( °c ) : 180 & 540, pipedimension & connection:ø48x10sw, class :4500, size:1.5 , zero passing integrated metal seated manual ball valve. forged alloy steel ( f22 ) lever operated, press ( bar ) & temp ( °c ) : 180 & 540, pipedimension & connection:ø60x11sw, class :4500, size:2 , zero passing integrated metal seated manual ball valve. forged carbon steel, socket weld. remote operated with 5 7kg air pressure air to close ( no air to open ) , pneumatic steam drain isolation ball valve with pneumatic actuator, press ( bar ) & temp ( °c ) : 45 & 540, pipedimension & connection:ø48x10sw, class :2500, size:1.5...

Indian Army - Haryana

35867223 bids are invited for retainer gasket , connection fuel drain , bolt shoe , clamp , shoe track single grouser 560mm , pivot pin alloy steel , ferrule , fuse , bulb 12v 6w , bulb instrument , seal , ball joint , bucket intermediate hose , bushes bucket cylinder head end , loader arm pin tower end mse total quantity : 257...

Panchayat Raj Department - Haryana

35857322 tender for installation of gym material at village bahiya block rania 1 `superior olympic bench flat ( made up of mainly olympic rectangular pipe of 4`x2`` approx.: more nearest to approx. 170x168x137 cm with 2.15mm thickness, heavy cushion padding on 12mm plys with special non abrasive fabric non tearing fabric. with two vertical pipes have clamp forresting rodonit, used for doing flatpattern chestpressat one fixed level ) ` 2 `superior olympic bench incline ( made up of mainly olympic rectangular pipe of 4`x2` approx.:more nearest to approx. 163x165x137 cm with 2.15mm thickness, heavy cushion padding on 12mm plys with special non abrasive fabric non tearing fabric. with two vertical pipes have clamp forresting robonit, used for doing incline level pattern chest press at one fixed incline level ) .` 3 arm wheel:providing, designing and fixing arm wheel in a pair of size 850x800x1800mm 4 heavy dumbells stand / rackin double platform: ( made up of mainly olympic rectangular pipe of 4’x2’ appox, : more nearest to approx.. 209x81x83 cm with 2.15mm thickness , with angleiron welded with flat patti with rubber pasted on which dumbbell srestonint, two platform / shelves ) 5 providing, designing and fixing leg press size 153x137x152 cm fabricated with 2`x4` rectangular hollow pipe with 3.00 mm thick and powder coated using akzo nobel or equivalent of 80 120 micron thick. all welding joints of pipe are well welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. zinc primer paint to be applied at all weldings points prior to finishing. handle bars are to be provided with high quality grip rubber at top end. padals shall be made upto of nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin lldpe manufactured by rotational moulding with minimum thickness of plastic 4.00 mm , colourful and u v resistant environmental friendly, bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by engineer in charge. equipment to be fitted within built limiters to prevent unwanted movements. all open ends of pipe to be coloured by gi / lldpe caps for user safety. the equipment to be fixed on ground with concrete of minimum strength m25 and j shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of engineer in charge regarding material, shape of equipment, colour on metal, seat and basecover plaste and fixing of equipment etc. 6 seated chest press: dimensions: 170x120x66, frame structures:over sized internal frame tubing of high tensile strength steel, gracefully curved continuous welded, factory assembled weight frame.name of tube: oval tubingtube size: 122mm x 58mmtube gauge: 4mm 7 spare flat bench for dumbbell fly exercise: ( made up of mainly olympic rectangular pipe of 4’x2’ approx, ” more nearest to approx. 121x75x46 cm with 2.15 mm thickness. heavy cushion padding on 12mm plys with special non abrasive fabric non tearing fabric ) 8 superior olympic bench decline: ( made up of mainly olympic rectangular pipe of 4’ x 2’ approx.:more nearest to approx.. 210x166x137cm with 2.15mm thickness, heavy cushion padding on 12mm plys with special non abrasive fabric non tering fabric. with two vertical pipes have clampfor resting rod on it, used for doing decline level pattern chest press at one fixed decline level with leg locking 9 twister:providing designing and fixing twister of size 1700x1300x1300 mm fabricated 2”x4” rectangular hellow ms pipe and powder coated using. akzo nobel or equivalent of 80 120 micron thick . all welding joint of ipe are well welded with joints scalloped as necessary and dressed off removing sharp edge and burrs. 10 cycleadjustable height and comfortable seat with cushions to prevent back aches and muscle stiffness.8 adjustable resistance levels and tension controller knob.material alloy steel. 6 months warranty. size ( l*b*h* ) ( 41*24*6 ) inches.dual action mode stationary and moving handles both. full body workout arms, calves, chest and back.belt based resistance mechanism allows better, momentum based recovery and better pedalling technique.suitable for high intensity cardio workout, weight loss, fully body workout and strangth training. 11 push up bar:pipe dimension – main post 140mm dia and other post 40mm dia.all joint shell be lubricated made by reputed company to be approved by engineer in charge. equipment to be fitted within built limiters to prevent unwanted movements. all open ends of pipe to be coloured by gi / lldpe caps for user safety. 12 plates 250 kg ( 20, 15, 10, 5, 2, 5 ) made from high quality rubber, tear proof, soundless and bouncy effect 13 rods7f / 3 and 3f / 2 = 27...

Indian Army - Haryana

35808458 bids are invited for r1 spare toe plate , pivot pin , pivot pin alloy steel , side cutter rh , side cutter lh , cold starter kit , pressure hose , stainer , handle rh , handle lh , gasket , seal kit , working light , rear light , water temp sensor , starter switch , hour cable , starter relay , knob , throttle cable , oil filter , shim kit , brake piston , brake piston seal , break piston seal , shim 0.5 mm , hose 10 bsp hp 700mm , hose 10 bsp lp 950m , hose 08 bsp hp 1910mm a , bolt banjo , belt front , air filter , bearing liner , gas strut, 700n , cap fuel tank , cap filler breather , joint universal , break assy , cable parking break , throttle cable assy , tooth bucket , cable battery positive ve , cable battery negitive ve , light headlamp total quantity : 228...

Department Of Fertilizers - Haryana

35648974 bids are invited for alloy steel electrode , cs welding electrode 2.5 mm , cs welding electrode 3.15mm total quantity : 1910...

Haryana Power Generation Corporation Limited - Haryana

35268877 supply of emergency drain control valve of hph 7and8 , high pressure heater (hph 7) emergency drain control valve application: high pressure heater (hph 7) emergency drain control valve, size:4 body style globe, mass flow rate liquid (wi) 171540 kg/h, temperatureratings for standard classastm a217 grade wc9 valves (in accordance with asme b16.34) rating cl900, body wc9 alloy steel, end connection butt welded sch 80, cage: sst, seat ring: sst valve plug: sst, equal percentage flow characteristic, equal percentage cage, hydrodynamic trim valve lpa (lpae1m) <85db(a), push down to close, cl5 leakage, shutoff class ansi cl v, pneumatic actuator push down to close & 75 psi maximum casing press, smart positioner, air fail to open, handwheel handwheel for manual operation. working parameters: valve inlet pressure & temp:4.81mpa & 265 deg c, valve outlet pressure: under vacuum 0.92bar , high pressure heater (hph 8) emergency drain control valve application: high pressure heater (hph 8) emergency drain control valve, size:3 body style globe, mass flow rate liquid (wi) 85890 kg/h, temperatureratings for standard classastm a217 grade wc9 valves (in accordance with asme b16.34) rating cl1500, body wc9 alloy steel, end connection butt welded sch 80, cage: sst, seat ring: sst valve plug: sst, equal percentage flow characteristic, equal percentage cage, hydrodynamic trim valve lpa (lpae1m) <85db(a), push down to close, cl5 leakage, shutoff class ansi cl v, pneumatic actuator push down to close & 75 psi maximum casing press, smart positioner, air fail to open, handwheel handwheel for manual operation. working parameters: valve inlet pressure & temp:7.58mpa & 295 deg c, valve outlet pressure: under vacuum 0.92bar...

Engineers India Limited - Haryana

35212719 supply of pressure vessel cs (up to 25 mm), pressure vessel low alloy steel, pressure vessel ltcs pressure vessel cs (up to 25 mm), pressure vessel low alloy steel, pressure vessel ltcs , supply of following items on fot dispatch point basis (including all taxes and duties excluding gst) as per complete scope of mr , 03 vv 00 052 hp receiver , 03 vv 00 054 condensate drum , 03 vv 00 055 debutanizer refluxdrum , 03 vv 00 056 blowdown condensate drum , 03 vv 00 057 stripper reboiler condensate pot , 03 vv 00 058 blowdown quench oil heater condensate pot , 03 vv 00 059 fractainator overhead reflux drum , 03 vv 00 060 fuel gas kod , 03 vv 00 061 flare knock out drum , 03 vv 00 101 1st stage caustic wash contactor and separator , 03 vv 00 102 2nd stage caustic wash contactor and separator , 03 vv 00 103 lpg sand filter vessel => limited...

Engineers India Limited - Haryana

35099222 tender for heat exchanger low alloy steel., heat exchanger cs / las+ss clad supply of following items on fot dispatch point basis ( including all taxes and duties excluding gst ) as per complete scope of mr. for billing & payment purpose, the weightage of each tag / heat exchanger ingroup a1 shall be 50% , in group a2 shall be 50% , in group a3 shall be 50% and ingroup a4 shall be 34% for tag no. 03 ee 00 005 b, 33% for tag no. 03 ee 00 005 c and 33% for tag no. 03 ee 00 005 d. 2 group a1 :uco / gas oil product exchanger tag no : 03 ee 00 001 c ( 1 nos ) , 03 ee 00 001 d ( 1 nos ) 3 group a2 : uco / coker hgo product exchanger , tag no :03 ee 00 002 c ( 1 nos ) , 03 ee 00 002 d ( 1 nos ) 4 group a3 : uco / coker hgo cr exchanger, tag no :03 ee 00 004 c ( 1 nos ) and uco / coker hgo product exchanger, tag no. 03 ee 00 004 d ( 1 nos ) 5 group a4 : uco / coker hgo product exchanger , tag no : 03 ee 00 005 b ( 1 nos ) , 03 ee 00 005 c ( 1 nos ) and tag no : 03 ee 00 005 d ( 1 nos ) 6 bd quench oil heater tag no : 03 ee 00 056 7 stripper reboiler tag no : 03 ee 00 057 8 debutanizer reboiler tag no : 03 ee 00 061...

Panchayat Raj Department - Haryana

35020897 purchase of machines / apparatus for gym at village garhi sampla 2 10 heavy dumbells stand / rackin double platform ( made up of mainly olympic rectangular pipe of 4’ x2’ approx.: more nearest to approx.2o9x81x83 cm with 2.15mm thickness, with angleiron welded with flat patti with rubber pasted on whichdumbbell srestonit, two platform / shelves ) 3 12 cycle : adjustable height and comfortable seat with cushions to prevent back aches and muscle stiffness.8 adjustable reslstance levels and tension controller knob. material alloy steel. 6 months warranty. size ( l’b*h ) ( 41*24*46 ) incites.dual actlon mode stationary and movlng handles both. full body workout arms, calves, chest and back.belt based resistance mechan lsm allows better momentum based recovery and better pedalllng technlque.suitable for hlgh intensity cardia workout, weight loss, full body workout and strength trainlng. 4 7 superior olympic bench decline : ( made up of malnly olymplc rectangular pipe ol 4‘ x2’ approx.: more nearest to approx.2 10x1g6x137 cm wlth 2.15mm tl›lctness, heavy cushion padding on12 mm plys wlh specla1 non abraslve fabrlc non tearing fabrlc. with two vertical plpes have clampfor resting rod on it, used for dolng decline level pattern chest press at one fixed decline level wlth leg locking ) 5 8 spare flat bench for dumbbell fly exercise : ( made up of mainly olymplc rectangular pipe of 4’ x2’ approx.: more nearest to approx12 1x7sx46 cm with 2.15mm thickness, heavy cushion padding on12mm plys wth special non abrasive fabric non tearing fabric. ) 6 arm wheel: provldlng, deslgnlng and flxlng arm wheel in a palr of slre 850 x 800 x 7 dumble 25o kg. ( 20, 15, 10.5.2.5 ) made from high quality rubbertear proef, soundless and bouncy effht. 8 functional 7raineit mechint : all pipes made ‹ip size 2” x4“ ol hot rolled hollow rectangular ms plpe wiih ›i e 153s 100s zzo cm anti powder coä ted u slng akzo nobel or pqtiiv, aient of 80 1 20 n›icron tljlck. all welrllng jolnts of plpe are well‹velrled with jolnts scalloprd as necessary and dressed olf removingshaip edges and burrs. zlnc primer pain [ to be applied at all weldlng points prior to finishing. handle bars are to be provided with high qualit y grip rubber. padals shall be made up of nylon alloy with rounded edge ol prevent any impact of in¡ury and seat to be made from virgin ltdpe mant›facturcd by rotalional moulding with minimumthickness of plastic 4.00mm, colourful and u v resistant environmentalfriendly. ßearing used shall be malntenance free, duly olled sealed and self lubricated made by reputed company to be approved by englneer in charge. equipmenl to be fitted within built llmiters to prevent unwan el movements. all open ends al pipe to be coloured by gi / llope caps for user safety. the equipment to be fixed on ground with concrete of minimum strength m25 and j shaped welded bolts and once the concrete is set, fix the equlpment on to it and cover nutsand bolts with the base plate cover, all complete as per direction and approval of engineer in charge regardlng material, shape of equipment, colour on metal, seat and base cover plate and fixing of equipment etc. 9 heaw olympic weight plates stand / rack in tree shape : ( made up of mainly olympic rectangular pipe of 4` x2` approx.: more nearest to approx.96x63x120 cm wlth 2.15mm thickness, with 6 round pipes welded ( 3 pipes on each side ) on which weigh plates are hanged / holded ) 10 multy gym six station ( leg pull, leg curl with leg extension, biceps with trlceps, pec dee fly ) : consists of 4 weighted stations and z light stations: and it is«omhinalion of 8 type of excerslce thls is macle up of mainly olympic rectangular pipe of 4’ x2’ with 2.15mm thickness with steel twisted wire with pvc / nyioncoated cable5mm 6mm: with pvc coated weight plates for noiseless working / movements, weight plates stack moves / slides in stainless steel pipes for smooth and noiseless movement throughout lifespan of equipments, ball bearing mouted fibre / pvcpullys, heavy ct›shionpadding on 12mm plys with special non abrasive fabric nontearing tauric.each weight stackis 7skg sheavy. 11 plates 250kg made from high quality rubber tear proof 12 providing, designing and fixing leg press size 153x137x152 cm fabricated with 2“x4” rectangular hollow pipe with 3.00 mm thick and powder coated using akzo nobel or equivalent ofg0 120 micron thick. allweldingjointsofpipearewellwelded withjoints scalloped as necessary and dressed off removing sharp edges and burrs. zinc primer palnt to be applied at all welding points prior to finishing. handle bars are to be pravided with high quality grip rubber at top end. padals shall be made up of nylon alloy withroundededge of prevent any impact of injury and seat to be made from virgin lldpe manufactured by rotational moulding with minimum thickness of plastic 4.00mm, colourful and u v resistant environmental friendly.bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by engineer in charge. equipment to be fitted wlthin built limiters to prevent unwanted movements. all open ends of pipe to be coloured by gi / lldpe caps for user safety. the equipmentto befixed onground withconcreteof minimum strength m2sand j shaped welded bolts and once the concrete is set, flx the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of engineer in charge regarding material, shape of equipment, colour on metal, seat and basecover plate and0xlng of equipment etc 13 rod stand 14 rods 7f / 3 and 3f / 2 =27f 15 seated chest press : dimensiuns : 170x120x166.frame structures : over sized internal frame tubing of hlgh tensile strength stnel, gracefully curved continuous welded, factory assembled weight frame. name of tube : oval tubing.tube size : 1z2 mm x 58 mm. tube gauge : 4 mm.welght stack : 80 kgs. 16 superior olympic 8ench incline : ( madu up ol mainly olympic rectangular pipe of 4’ x2’ approx.: mure ‹dearest to approx. t63x165x137 cm wilh 2.15mm thickness, heavy cull iur› j›addinj: on 12mm plys with special non abrasive labric non luaiing fakrlc, with two vertical pipes have clamp forr‹`siing rodortit, u›e‹j for dolng incline level pattern› chest press at orje lix0d inclinu il`vl`i ) . 17 superior olympic bench flat : ( made up of mainly olympic rectangular pipe of 4‘ x2‘ approx. : more nearest to approx. 170 x t68x137 cm with 2.15mm thlckness, heavy cusf›iurj padding un 12mm plys wth special non abrasive fabrlc non sparing fahric. wilh two vertical pipes have clamp forrestlng rodonlt, used for doing flatpattern cl estpiessac one f ixed level ) ...

Indian Oil Corporation Limited - Haryana

34829111 supply of flanges and adaptors cs / as / ss / ltcs supply of flanges and adaptors cs / as / ss / ltcs for cdw and pp units , supply of flange and adaptor carbon steel ( cpmsl cat1.15 as per nov 2022 ) , wn flg, cs b16.5, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs b16.47, sr.b, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs b16.47, sr.b, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs ( nace ) b16.5, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs ( nace ) b16.5, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs ( nace ) b16.5, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs ( nace ) b16.5, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs ( nace ) b16.5, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 150, 0 bw end, sch xs a105 , wn flg, cs b16.5, rf cl. 150, 0 bw end, sch xs a105 , wn flg, cs b16.5, rf cl. 150, 0 bw end, sch xs a105 , wn flg, cs b16.47, sr.b, rf cl. 150, 0 bw end, sch xs a105 , wn flg, cs ( nace ) b16.5, rf cl. 150, 0 bw end, sch xs a105 , wn flg, cs ( nace ) b16.5, rf cl. 150, 0 bw end, sch xs a105 , wn flg, cs ( nace ) b16.5, rf cl. 150, 0 bw end, sch xs a105 , wn flg, cs b16.5, rf cl. 150, 0 bw end, sch 160 a105 , wn flg, cs b16.5, rf cl. 150, 0 bw end, sch 160 a105 , wn flg, cs b16.5, rf cl. 150, 0 bw end, sch 160 a105 , wn flg, cs ( nace ) b16.5, rf cl. 150, 0 bw end, sch 160 a105 , wn flg, cs ( nace ) b16.5, rf cl. 150, 0 bw end, sch 160 a105 , wn flg, cs b16.5, rf cl. 300, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 300, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 300, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 300, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 300, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 300, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 300, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 300, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 300, 0 bw end, sch std a105 , wn flg, cs ( nace ) b16.5, rf cl. 300, 0 bw end, sch std a105 , wn flg, cs ( nace ) b16.5, rf cl. 300, 0 bw end, sch std a105 , wn flg, cs ( nace ) b16.5, rf cl. 300, 0 bw end, sch std a105 , wn flg, cs ( nace ) b16.5, rf cl. 300, 0 bw end, sch std a105 , wn flg, cs ( nace ) b16.5, rf cl. 300, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 300, 0 bw end, sch xs a105 , wn flg, cs b16.5, rf cl. 300, 0 bw end, sch xs a105 , wn flg, cs b16.5, rf cl. 300, 0 bw end, sch xs a105 , wn flg, cs b16.5, rf cl. 300, 0 bw end, sch xs a105 , wn flg, cs b16.5, rf cl. 300, 0 bw end, sch xs a105 , wn flg, cs b16.5, rf cl. 300, 0 bw end, sch xs a105 , wn flg, cs b16.5, rf cl. 300, 0 bw end, sch xs a105 , wn flg, cs b16.5, rf cl. 300, 0 bw end, sch xs a105 , wn flg, cs ( nace ) b16.5, rf cl. 300, 0 bw end, sch xs a105 , wn flg, cs ( nace ) b16.5, rf cl. 300, 0 bw end, sch xs a105 , wn flg, cs ( nace ) b16.5, rf cl. 300, 0 bw end, sch xs a105 , wn flg, cs b16.5, rf cl. 300, 0 bw end, sch 160 a105 , wn flg, cs ( nace ) b16.5, rf cl. 300, 0 bw end, sch 160 a105 , wn flg, cs b16.5, rf cl. 600, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 600, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 600, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 600, 0 bw end, sch std a105 , wn flg, cs ( nace ) b16.5, rf cl. 600, 0 bw end, sch std a105 , wn flg, cs ( nace ) b16.5, rf cl. 600, 0 bw end, sch std a105 , wn flg, cs b16.5, rf cl. 600, 0 bw end, sch xs a105 , wn flg, cs b16.5, rf cl. 600, 0 bw end, sch xs a105 , wn flg, cs b16.5, rf cl. 600, 0 bw end, sch xs a105 , wn flg, cs b16.5, rf cl. 600, 0 bw end, sch xs a105 , wn flg, cs ( nace ) b16.5, rf cl. 600, 0 bw end, sch xs a105 , wn flg, cs ( nace ) b16.5, rf cl. 600, 0 bw end, sch xs a105 , wn flg, cs ( nace ) b16.5, rf cl. 600, 0 bw end, sch 160 a105 , wn flg, cs, b16.5, rf cl. 900, 0 bw ends, sch xs a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 150, 0 bw end, sch std a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 150, 0 bw end, sch xs a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 150, 0 bw end, sch xs a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 150, 0 bw end, sch xs a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 150, 0 bw end, sch 160 a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 150, 0 bw end, sch 160 a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 300, 0 bw end, sch std a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 300, 0 bw end, sch std a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 300, 0 bw end, sch std a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 300, 0 bw end, sch std a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 300, 0 bw end, sch std a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 300, 0 bw end, sch xs a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 600, 0 bw end, sch std a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 600, 0 bw end, sch std a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 600, 0 bw end, sch xs a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 600, 0 bw end, sch xs a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 600, 0 bw end, sch xs a105 , wn flg, cs, ( ibr ) b16.5, rf cl. 600, 0 bw end, sch xs a105 , wn flg, cs, large tongue b16.5, lt cl. 600, 0 bw ends, sch 160 a105 , wn flg, cs, ( h2 service ) b16.5, rtj cl. 900, 0 bw ends, sch xs a105 , wn flg, cs, ( h2 service ) b16.5, rtj cl. 900, 0 bw ends, sch 120 a105 , wn flg, cs, ( h2 service ) b16.5, rtj cl. 1500, 0 bw ends, sch xs a105 , wn flg, cs, ( h2 service ) b16.5, rtj cl. 1500, 0 bw ends, sch xs a105 , wn flg, cs, b16.5, rtj cl. 1500, 0 bw ends, sch 160 a105 , wn flg, cs, b16.5, rtj cl. 1500, 0 bw ends, sch 160 a105 , wn flg, cs, b16.5, rtj cl. 1500, 0 bw ends, sch 160 a105 , wn flg, cs, b16.5, rtj cl. 1500, 0 bw ends, sch 160 a105 , wn flg, cs, b16.5, rtj cl. 1500, 0 bw ends, sch 160 a105 , wn flg, cs, ( h2 service ) b16.5, rtj cl. 1500, 0 bw ends, sch 160 a105 , wn flg, cs, ( h2 service ) b16.5, rtj cl. 1500, 0 bw ends, sch 160 a105 , wn flg, cs, ( h2 service ) b16.5, rtj cl. 1500, 0 bw ends, sch 160 a105 , wn flg, cs, ( h2 service ) b16.5, rtj cl. 1500, 0 bw ends, sch 160 a105 , wn flg, cs, ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch 160 a105 , wn flg, cs, ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch 160 a105 , wn flg, cs, ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch 160 a105 , wn flg, cs, ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch 160 a105 , wn flg, cs, ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch 160 a105 , wn flg, cs, ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch 160 a105 , wn flg, cs, ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch 160 a105 , wn flg, cs, ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch 160 a105 , wn flg, cs, ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch xxs a105 , wn flg, cs, ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch xxs a105 , wn flg, cs, ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch xxs a105 , wn flg, cs, ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch xxs a105 , wn flg, cs, ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch xxs a105 , wn flg, cs, ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch xxs a105 , wn flg, cs, ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch xxs a105 , wn flg, cs, ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch xxs a105 , wn flg, cs, ( nace ) b16.5, rtj cl. 1500, 0 bw ends, sch xxs a105 , wn flg, cs, ( nace ) b16.5, rtj cl. 1500, 0 bw ends, sch xxs a105 , wn flg, cs, ( nace ) b16.5, rtj cl. 1500, 0 bw ends, sch xxs a105 , wn flg, cs, ( nace ) b16.5, rtj cl. 1500, 0 bw ends, sch xxs a105 , wn flg, cs, ( nace ) b16.5, rtj cl. 1500, 0 bw ends, sch xxs a105 , wn flg, cs b16.5, rtj cl. 2500, 0 bw ends, sch xxs a105 , wn flg, cs b16.5, rtj cl. 2500, 0 bw ends, sch xxs a105 , wn flg, cs b16.5, rtj cl. 2500, 0 bw ends, sch xxs a105 , wn flg, cs b16.5, rtj cl. 2500, 0 bw ends, sch xxs a105 , wn flg, cs b16.5, rtj cl. 2500, 0 bw ends, sch xxs a105 , wn flg, cs b16.5, rtj cl. 2500, 0 bw ends, sch xxs a105 , wn flg, cs b16.5, rtj cl. 2500, 0 bw ends, sch xxs a105 , wn flg, cs b16.5, rtj cl. 2500, 0 bw ends, sch xxs a105 , wn flg, cs, ( h2+nace ) b16.5, rtj cl. 2500, 0 bw ends, sch xxs a105n , wn flg, cs b16.5, rtj cl. 2500, 0 bw ends, 25.4 mm thk a105 , wn flg, cs, ( ibr ) b16.5, rtj cl. 1500, 0 bw ends, sch xs a105 , bf, cs b16.5, rf cl. 150, 0a105 , bf, cs b16.5, rf cl. 150, 0a105 , bf, cs b16.5, rf cl. 150, 0a105 , bf, cs b16.5, rf cl. 150, 0a105 , bf, cs b16.5, rf cl. 150, 0a105 , bf, cs b16.5, rf cl. 150, 0a105 , bf, cs b16.5, rf cl. 150, 0a105 , bf, cs b16.5, rf cl. 150, 0a105 , bf, cs b16.5, rf cl. 150, 0a105 , bf, cs b16.5, rf cl. 150, 0a105 , bf, cs b16.5, rf cl. 150, 0a105 , bf, cs b16.5, rf cl. 150, 0a105 , bf, cs b16.5, rf cl. 150, 0a105 , bf, cs ( nace ) b16.5, rf cl. 150, 0a105 , bf, cs ( nace ) b16.5, rf cl. 150, 0a105 , bf, cs ( nace ) b16.5, rf cl. 150, 0a105 , bf, cs b16.5, rf cl. 300, 0a105 , bf, cs b16.5, rf cl. 300, 0a105 , bf, cs b16.5, rf cl. 300, 0a105 , bf, cs b16.5, rf cl. 300, 0a105 , bf, cs b16.5, rf cl. 300, 0a105 , bf, cs b16.5, rf cl. 300, 0a105 , bf, cs b16.5, rf cl. 300, 0a105 , bf, cs b16.5, rf cl. 300, 0a105 , bf, cs ( nace ) b16.5, rf cl. 300, 0a105 , bf, cs ( nace ) b16.5, rf cl. 300, 0a105 , bf, cs ( nace ) b16.5, rf cl. 300, 0a105 , bf, cs ( nace ) b16.5, rf cl. 300, 0a105 , bf, cs ( nace ) b16.5, rf cl. 300, 0a105 , bf, cs ( nace ) b16.5, rf cl. 300, 0a105 , bf, cs ( nace ) b16.5, rf cl. 300, 0a105 , bf, cs ( nace ) b16.5, rf cl. 300, 0a105 , bf, cs ( nace ) b16.5, rf cl. 300, 0a105 , bf, cs b16.5, rf cl. 600, 0a105 , bf, cs b16.5, rf cl. 600, 0a105 , bf, cs b16.5, rf cl. 600, 0a105 , bf, cs b16.5, rf cl. 600, 0a105 , bf, cs b16.5, rf cl. 600, 0a105 , bf, cs b16.5, rtj cl. 2500, 0a105 , bf, cs b16.5, rtj cl. 2500, 0a105 , bf, cs ( ibr ) b16.5, rf cl. 150, 0a105 , bf, cs ( ibr ) b16.5, rf cl. 150, 0a105 , bf, cs ( ibr ) b16.5, rf cl. 150, 0a105 , bf, cs ( ibr ) b16.5, rf cl. 150, 0a105 , bf, cs ( ibr ) b16.5, rf cl. 150, 0a105 , bf, cs ( ibr ) b16.5, rf cl. 150, 0a105 , bf, cs ( ibr ) b16.5, rf cl. 150, 0a105 , bf, cs ( ibr ) b16.5, rf cl. 300, 0a105 , bf, cs ( ibr ) b16.5, rf cl. 300, 0a105 , bf, cs ( ibr ) b16.5, rf cl. 300, 0a105 , bf, cs ( ibr ) b16.5, rf cl. 300, 0a105 , bf, cs ( ibr ) b16.5, rf cl. 300, 0a105 , bf, cs ( ibr ) b16.5, rf cl. 300, 0a105 , bf, cs ( ibr ) b16.5, rf cl. 600, 0a105 , bf, cs ( ibr ) b16.5, rf cl. 600, 0a105 , bf, cs ( ibr ) b16.5, rf cl. 600, 0a105 , blind flange, cs ( galv ) b16.5 cl. 150, 0 ff a105 ( galv ) , blind flange, cs ( galv ) b16.5 cl. 150, 0 ff a105 ( galv ) , blind flange, cs ( galv ) b16.5 cl. 150, 0 ff a105 ( galv ) , blind flange, cs ( galv ) b16.5 cl. 150, 0 ff a105 ( galv ) , blind flange, cs ( galv ) b16.5 cl. 150, 0 ff a105 ( galv ) , blind flange, cs ( galv ) b16.5 cl. 150, 0 ff a105 ( galv ) , blind flange, cs ( galv ) b16.5 cl. 300, 0 rf a105 ( galv ) , blind flange, cs ( galv ) b16.5 cl. 300, 0 rf a105 ( galv ) , blind flange, cs ( galv ) b16.5 cl. 300, 0 rf a105 ( galv ) , bf, cs b16.5, rtj cl. 1500, 0a105 , bf, cs b16.5, rtj cl. 1500, 0a105 , bf, cs b16.5, rtj cl. 1500, 0a105 , bf, cs ( h2 service ) b16.5, rtj cl. 1500, 0a105 , bf, cs ( h2 service ) b16.5, rtj cl. 1500, 0a105 , bf, cs ( h2+nace ) b16.5, rtj cl. 1500, 0a105 , bf, cs ( h2+nace ) b16.5, rtj cl. 1500, 0a105 , bf, cs ( h2+nace ) b16.5, rtj cl. 1500, 0a105 , bf, cs ( h2+nace ) b16.5, rtj cl. 1500, 0a105 , bf, cs, ( nace ) b16.5, rtj cl. 1500, 0a105 , bf, cs, ( nace ) b16.5, rtj cl. 1500, 0a105 , bf, cs, ( nace ) b16.5, rtj cl. 1500, 0a105 , scrd flg , cs ( galv ) b16.5 cl. 150, 0 scrd ( f ) , b1.20.1, ff a105 ( galv ) , scrd flg , cs ( galv ) b16.5 cl. 150, 0 scrd ( f ) , b1.20.1, ff a105 ( galv ) , scrd flg , cs ( galv ) b16.5 cl. 150, 0 scrd ( f ) , b1.20.1, ff a105 ( galv ) , scrd flg , cs ( galv ) b16.5 cl. 150, 0 scrd ( f ) , b1.20.1, ff a105 ( galv ) , scrd flg , cs ( galv ) b16.5 cl. 150, 0 scrd ( f ) , b1.20.1, ff a105 ( galv ) , scrd flg , cs ( galv ) b16.5 cl. 150, 0 scrd ( f ) , b1.20.1, ff a105 ( galv ) , scrd flg , cs ( galv ) b16.5 cl. 150, 0 scrd ( f ) , b1.20.1, ff a105 ( galv ) , scrd flg , cs ( galv ) b16.5 cl. 300, 0 scrd ( f ) , b1.20.1, rf a105 ( galv ) , scrd flg , cs ( galv ) b16.5 cl. 300, 0 scrd ( f ) , b1.20.1, rf a105 ( galv ) , scrd flg , cs ( galv ) b16.5 cl. 300, 0 scrd ( f ) , b1.20.1, rf a105 ( galv ) , scrd flg , cs ( galv ) b16.5 cl. 300, 0 scrd ( f ) , b1.20.1, rf a105 ( galv ) , slip on flg, cs, ( galv ) b16.5 cl. 150, 0 ff a105, ( galv ) , slip on flg, cs, ( galv ) b16.5 cl. 150, 0 ff a105, ( galv ) , slip on flg, cs, ( galv ) b16.5 cl. 300, 0 rf a105, ( galv ) , slip on flg, cs, ( galv ) b16.5 cl. 300, 0 rf a105, ( galv ) , so flg, cs b16.5, rf cl. 150, 0a105 , so flg, cs b16.5, rf cl. 150, 0a105 , so flg, cs b16.5, rf cl. 150, 0a105 , so flg, cs b16.5, rf cl. 150, 0a105 , so flg, cs b16.5, rf cl. 150, 0a105 , so flg, cs b16.5, rf cl. 150, 0a105 , so flg, cs b16.5, rf cl. 150, 0a105 , so flg, cs b16.5, rf cl. 150, 0a105 , sw flg, cs b16.5, rf cl. 150, 0 sw ends, sch xs a105 , sw flg, cs b16.5, rf cl. 150, 0 sw ends, sch xs a105 , sw flg, cs b16.5, rf cl. 150, 0 sw ends, sch 160 a105 , sw flg, cs b16.5, rf cl. 300, 0 sw ends, sch xs a105 , sw flg, cs b16.5, rf cl. 300, 0 sw ends, sch xs a105 , sw flg, cs ( nace ) b16.5, rf cl. 300, 0 sw ends, sch xs a105 , sw flg, cs ( nace ) b16.5, rf cl. 300, 0 sw ends, sch xs a105 , sw flg, cs b16.5, rf cl. 300, 0 sw ends, sch 160 a105 , sw flg, cs b16.5, rf cl. 300, 0 sw ends, sch 160 a105 , sw flg, cs b16.5, rf cl. 300, 0 sw ends, sch 160 a105 , sw flg, cs ( nace ) b16.5, rf cl. 300, 0 sw ends, sch 160 a105 , sw flg, cs ( nace ) b16.5, rf cl. 300, 0 sw ends, sch 160 a105 , sw flg, cs ( nace ) b16.5, rf cl. 300, 0 sw ends, sch 160 a105 , sw flg, cs ( nace ) b16.5, rf cl. 300, 0 sw ends, sch 160 a105 , sw flg, cs b16.5, rf cl. 300, 0 sw ends, sch xxs a105 , sw flg, cs ( nace ) b16.5, rf cl. 300, 0 sw ends, sch xxs a105 , sw flg, cs b16.5, rf cl. 600, 0 sw ends, sch xs a105 , sw flg, cs b16.5, rf cl. 600, 0 sw ends, sch xs a105 , sw flg, cs b16.5, rf cl. 600, 0 sw ends, sch 160 a105 , sw flg, cs b16.5, rf cl. 600, 0 sw ends, sch 160 a105 , sw flg, cs ( ibr ) b16.5, rf cl. 300, 0 sw end, sch xs a105 , sw flg, cs ( ibr ) b16.5, rf cl. 300, 0 sw end, sch xs a105 , sw flg, cs ( ibr ) b16.5, rf cl. 300, 0 sw end, sch 160 a105 , sw flg, cs ( ibr ) b16.5, rf cl. 300, 0 sw end, sch 160 a105 , sw flg, cs ( ibr ) b16.5, rf cl. 600, 0 sw end, sch xs a105 , sw flg, cs ( ibr ) b16.5, rf cl. 600, 0 sw end, sch xs a105 , sw flg, cs ( ibr ) b16.5, rf cl. 600, 0 sw end, sch 160 a105 , sw flg, cs ( ibr ) b16.5, rf cl. 600, 0 sw end, sch 160 a105 , adaptor, flgd, cs pinles pip 6265 a105 , adaptor, flgd, cs pinles pip 6265 a105 , adaptor, flgd, cs pinles pip 6265 a105 , adaptor, flgd, cs ( ibr ) pinles pip 6265 a105 , adaptor, cs pinles pip 6265 a105 , adaptor, cs pinles pip 6265 a105 , adaptor, sw, cs pinles pip 6265 a105 , adaptor, cs ( nace ) pinles pip 6265 a105 , adaptor, cs ( ibr ) pinles pip 6265 a105 , adaptor, cs ( h2+nace ) pinles pip 6265 a105 , adaptor, cs ( nace ) pinles pip 6265 a105 , adaptor, cs ( h2+nace ) pinles pip 6265 a105 , supply of flange alloy steel ( cpmsl cat1.16 as per nov 2022 ) , wn flg, as b16.5, rf cl. 300, 0 bw end, sch std a182 gr.f9 , wn flg, as ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch 160 a182 gr.f11 cl.2 , wn flg, as ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch 160 a182 gr.f11 cl.2 , wn flg, as ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch xxs a182 gr.f11 cl.2 , wn flg, as ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, a182 gr.f11 cl.2 , wn flg, as ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, a182 gr.f11 cl.2 , wn flg, as ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, a182 gr.f11 cl.2 , wn flg, as ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch 160 a182 gr.f22 cl.3 , wn flg, as ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch 160 a182 gr.f22 cl.3 , wn flg, as ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch 160 a182 gr.f22 cl.3 , wn flg, as ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch 160 a182 gr.f22 cl.3 , wn flg, as ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch 160 a182 gr.f22 cl.3 , wn flg, as ( h2+nace ) b16.5, rtj cl. 1500, 0 bw ends, sch 160 a182 gr.f22 cl.3 , wn flg, as ( h2+nace ) b16.5, rtj cl. 2500, 0 bw ends, sch 160 a182 gr.f22 cl.3 , wn flg, as ( h2+nace ) b16.5, rtj cl. 2500, 0 bw ends, sch 160 a182 gr.f22 cl.3 , wn flg, as ( h2+nace ) b16.5, rtj cl. 2500, 0 bw ends, sch 160 a182 gr.f22 cl.3 , wn flg, as ( h2+nace ) b16.5, rtj cl. 2500, 0 bw ends, sch 160 a182 gr.f22 cl.3 , wn flg, as ( h2+nace ) b16.5, rtj cl. 2500, 0 bw ends, sch 160 a182 gr.f22 cl.3 , bf, as ( h2+nace ) b16.5, rtj cl. 1500, 0a182 gr.f11 cl.2 , bf, as ( h2+nace ) b16.5, rtj cl. 1500, 0a182 gr.f11 cl.2 , bf, as ( h2+nace ) b16.5, rtj cl. 1500, 0a182 gr.f11 cl.2 , bf, as ( h2+nace ) b16.5, rtj cl. 1500, 0a182 gr.f22 cl.3 , bf, as ( h2+nace ) b16.5, rtj cl. 1500, 0a182 gr.f22 cl.3 , bf, as ( h2+nace ) b16.5, rtj cl. 1500, 0a182 gr.f22 cl.3 , sw flg, as b16.5, rf cl. 300, 0 sw ends, sch xs a182 gr.f9 , sw flg, as b16.5, rf cl. 300, 0 sw ends, sch 160 a182 gr.f9 , supply of flange and adaptor stainless steel ( cpmsl cat1.17 as per nov 2022 ) , wn flg, ss b16.5, rf cl. 300, 0 bw end, sch 10s a182 gr.f304 , wn flg, ss b16.5, rf cl. 300, 0 bw end, sch 10s a182 gr.f304 , wn flg, ss b16.5, rf cl. 300, 0 bw end, sch 10s a182 gr.f304 , wn flg, ss b16.5, rf cl. 300, 0 bw end, sch 10s a182 gr.f304 , wn flg, ss b16.5, rf cl. 300, 0 bw end, sch std a182 gr.f304 , wn flg, ss b16.5, rf cl. 300, 0 bw end, sch 40s a182 gr.f304 , wn flg, ss b16.5, rf cl. 300, 0 bw end, sch 40s a182 gr.f304 , wn flg, ss b16.5, rf cl. 300, 0 bw end, sch 40s a182 gr.f304 , wn flg, ss, ( nace ) b16.5, rf cl. 300, 0 bw end, sch 10s a182 gr.f304l , wn flg, ss, ( nace ) b16.5, rf cl. 300, 0 bw end, sch 40s a182 gr.f304l , wn flg, ss, ( nace ) b16.5, rf cl. 300, 0 bw end, sch 40s a182 gr.f304l , welding neck flange, ss b16.5, rf cl. 150, 0 bw end, sch 10s a182 gr.f304 , welding neck flange, ss b16.5, rf cl. 150, 0 bw end, sch 10s a182 gr.f304 , welding neck flange, ss b16.5, rf cl. 150, 0 bw end, sch 10s a182 gr.f304 , welding neck flange, ss b16.5, rf cl. 150, 0 bw end, sch 10s a182 gr.f304 , welding neck flange, ss b16.5, rf cl. 150, 0 bw end, sch 10s a182 gr.f304 , welding neck flange, ss b16.5, rf cl. 150, 0 bw end, sch 10s a182 gr.f304 , welding neck flange, ss b16.5, rf cl. 150, 0 bw end, sch 10s a182 gr.f304 , welding neck flange, ss b16.5, rf cl. 150, 0 bw end, sch 10s a182 gr.f304 , welding neck flange, ss b16.5, rf cl. 150, 0 bw end, sch 10s a182 gr.f304 , welding neck flange, ss b16.5, rf cl. 150, 0 bw end, sch 40s a182 gr.f304 , welding neck flange, ss b16.5, rf cl. 150, 0 bw end, sch 40s a182 gr.f304 , welding neck flange, ss b16.5, rf cl. 150, 0 bw end, sch 40s a182 gr.f304 , wn flange, ss b16.5, rf cl. 150, 0 bw end, sch 80s a182 gr.f304 , wn flange, ss b16.5, rf cl. 150, 0 bw end, sch 80s a182 gr.f304 , welding neck flange, ss b16.5 cl. 300, 0 bw end, sch 10s, rf a182 gr.f304 , welding neck flange, ss b16.5 cl. 300, 0 bw end, sch 10s, rf a182 gr.f304 , welding neck flange, ss b16.5 cl. 300, 0 bw end, sch 10s, rf a182 gr.f304 , welding neck flange, ss b16.5 cl. 300, 0 bw end, sch 40s, rf a182 gr.f304 , wn flg, ss ( h2 ser. ) b16.5 cl. 300, 0 bw end, sch 40s, rf a182 gr.f304 , welding neck flange, ss b16.5 cl. 600, 0 bw end, sch 40s, rf a182 gr.f304 , welding neck flange, ss b16.5 cl. 600, 0 bw end, sch 40s, rf a182 gr.f304 , welding neck flange, ss b16.5 cl. 600, 0 bw end, sch 40s, rf a182 gr.f304 , welding neck flange, ss b16.5 cl. 600, 0 bw end, sch 40s, rf a182 gr.f304 , welding neck flange, ss b16.5 cl. 600, 0 bw end, sch 40s, rf a182 gr.f304 , welding neck flange, ss b16.5 cl. 600, 0 bw end, sch 40s, rf a182 gr.f304 , welding neck flange, ss b16.5 cl. 600, 0 bw end, sch 40s, rf a182 gr.f304 , wn flg, ss ( h2 ser. ) b16.5 cl. 600, 0 bw end, sch 40s, rf a182 gr.f304 , wn flg, ss b16.5 cl. 150, 0 bw end, sch 10s, rf a182 gr.f316 , wn flg, ss b16.5 cl. 150, 0 bw end, sch 10s, rf a182 gr.f316 , wn flg, ss b16.5 cl. 150, 0 bw end, sch 10s, rf a182 gr.f316 , wn flg, ss b16.5 cl. 150, 0 bw end, sch 40s, rf a182 gr.f316 , wn flg, ss b16.5 cl. 150, 0 bw end, sch 40s, rf a182 gr.f316 , wn flg, ss b16.5 cl. 150, 0 bw end, sch 80s, rf a182 gr.f316 , wn flg, ss b16.5 cl. 300, 0 bw end, sch 10s, rf a182 gr.f316 , wn flg, ss b16.5 cl. 300, 0 bw end, sch 40s, rf a182 gr.f316 , wn flg, ss b16.5 cl. 600, 0 bw end, sch 10s, rf a182 gr.f316 , wn flg, ss, large groove b16.5, lg cl. 300, 0 bw ends, sch 40s a182 gr.f304 , wn flg, ss, large groove b16.5, lg cl. 300, 0 bw ends, sch 40s a182 gr.f304 , wn flg, ss, large tongue b16.5, lt cl. 300, 0 bw ends, sch 40s a182 gr.f304 , wn flg, ss, large groove b16.5, lg cl. 300, 0 bw ends, sch 80s a182 gr.f304 , wn flg, ss, large tongue b16.5, lt cl. 300, 0 bw ends, sch 80s a182 gr.f304 , wn flg, ss b16.5, lg cl. 600, 0 bw ends, sch 40s a182 gr.f304 , wn flg, ss b16.5, lg cl. 600, 0 bw ends, sch 40s a182 gr.f304 , wn flg, ss, large tongue b16.5, lt cl. 600, 0 bw ends, sch 40s a182 gr.f304 , wn flg, ss b16.5, lg cl. 600, 0 bw ends, sch 80s a182 gr.f304 , wn flg, ss b16.5, lg cl. 600, 0 bw ends, sch 80s a182 gr.f304 , wn flg, ss b16.5, lt cl. 600, 0 bw ends, sch 80s a182 gr.f304 , wn flg, ss b16.5, lt cl. 600, 0 bw ends, sch 80s a182 gr.f304 , wn flg, ss b16.5, lt cl. 600, 0 bw ends, sch 80s a182 gr.f304 , wn flg, ss b16.5, lt cl. 600, 0 bw ends, sch 80s a182 gr.f304 , wn flg, ss b16.5, rf cl. 1500, 0 bw ends, sch 40s a182 gr.f304 , wn flg, ss b16.5, rf cl. 1500, 0 bw ends, sch 40s a182 gr.f304 , wn flg, ss b16.5, rf cl. 1500, 0 bw ends, sch 80s a182 gr.f304 , wn flg, ss b16.5, rf cl. 1500, 0 bw ends, sch 80s a182 gr.f304 , wn flg, ss b16.5, rf cl. 1500, 0 bw ends, sch 80s a182 gr.f304 , wn flg, ss, large female facing b16.5, lf cl. 1500, 0 bw ends, sch 80s a182 gr.f304 , wn flg, ss, large female facing b16.5, lf cl. 2500, 0 bw ends, sch 80s a182 gr.f304 , wn flg, ss, large female facing b16.5, lf cl. 2500, 0 bw ends, sch 160 a182 gr.f304 , wn flg, ss, large female facing b16.5, lf cl. 2500, 0 bw ends, sch 160 a182 gr.f304 , wn flg, ss, ( nace ) b16.5, rtj cl. 1500, 0 bw end, 4.4 mm thk a182 gr.f304l , wn flg, ss, ( nace ) b16.5, rtj cl. 1500, 0 bw end, 9.3 mm thk a182 gr.f304l , wn flg, ss ( h2+nace ) b16.5, rtj cl. 2500, 0 bw end, sch 160 a182 gr. f321 , wn flg, ss ( h2+nace ) b16.5, rtj cl. 2500, 0 bw end, sch 160 a182 gr. f321 , wn flg, ss ( h2+nace ) b16.5, rtj cl. 2500, 0 bw end, sch 160 a182 gr. f321 , wn flg, ss ( h2+nace ) b16.5, rtj cl. 2500, 0 bw end, sch 160 a182 gr. f321 , wn flg, ss ( h2+nace ) b16.5, rtj cl. 2500, 0 bw end, sch xxs a182 gr. f321 , wn flg, ss ( h2+nace ) b16.5, rtj cl. 2500, 0 bw end, sch xxs a182 gr. f321 , wn flg, ss ( h2+nace ) b16.5, rtj cl. 2500, 0 bw end, sch xxs a182 gr. f321 , bf, ss b16.5, rf cl. 300, 0a182 gr.f304 , bf, ss b16.5, rf cl. 300, 0a182 gr.f304 , bf, ss b16.5, rf cl. 300, 0a182 gr.f304 , bf, ss b16.5, rf cl. 300, 0a182 gr.f304 , bf, ss, ( nace ) b16.5, rf cl. 300, 0a182 gr.f304l , blind flange, ss b16.5 cl. 150, 0 rf a182 gr.f304 , blind flange, ss b16.5 cl. 150, 0 rf a182 gr.f304 , blind flange, ss b16.5 cl. 150, 0 rf a182 gr.f304 , blind flange, ss b16.5 cl. 150, 0 rf a182 gr.f304 , blind flange, ss b16.5 cl. 150, 0 rf a182 gr.f304 , blind flange, ss b16.5 cl. 150, 0 rf a182 gr.f304 , blind flange, ss b16.5 cl. 150, 0 rf a182 gr.f304 , blind flange, ss b16.5 cl. 150, 0 rf a182 gr.f304 , blind flange, ss b16.5 cl. 300, 0 rf a182 gr.f304 , bf, ss ( h2 ser. ) b16.5 cl. 300, 0 rf a182 gr.f304 , bf, ss ( h2 ser. ) b16.5 cl. 300, 0 rf a182 gr.f304 , bf, ss ( h2 ser. ) b16.5 cl. 300, 0 rf a182 gr.f304 , blind flange, ss b16.5 cl. 600, 0 rf a182 gr.f304 , blind flange, ss b16.5 cl. 600, 0 rf a182 gr.f304 , blind flange, ss b16.5 cl. 600, 0 rf a182 gr.f304 , blind flange, ss b16.5 cl. 600, 0 rf a182 gr.f304 , blind flange, ss, ( h2 ser. ) b16.5 cl. 600, 0 rf a182 gr.f304 , blind flange, ss, ( h2 ser. ) b16.5 cl. 600, 0 rf a182 gr.f304 , blind flange, ss, ( h2 ser. ) b16.5 cl. 600, 0 rf a182 gr.f304 , bf, ss b16.5 cl. 150, 0 rf a182 gr.f316 , bf, ss b16.5 cl. 150, 0 rf a182 gr.f316 , bf, ss b16.5 cl. 150, 0 rf a182 gr.f316 , bf, ss b16.5 cl. 150, 0 rf a182 gr.f316 , bf, ss b16.5 cl. 300, 0 rf a182 gr.f316 , bf, ss b16.5 cl. 300, 0 rf a182 gr.f316 , bf, ss b16.5 cl. 300, 0 rf a182 gr.f316 , bf, ss b16.5 cl. 300, 0 rf a182 gr.f316 , bf, ss, ( nace ) b16.5 cl. 300, 0 rf a182 gr.f321 , bf, ss b16.5 cl. 150, 0 rf a182 gr.f904l , bf, lined, ss pinles pip 6288 cl. 150, 0 rf a515gr.70+uns n08904 , bf, ss, large groove b16.5, lg cl. 300, 0a182 gr.f304 , bf, ss, large groove b16.5, lg cl. 300, 0a182 gr.f304 , bf, ss, large tongue b16.5, lt cl. 300, 0a182 gr.f304 , bf, ss, large tongue b16.5, lt cl. 300, 0a182 gr.f304 , bf, ss, large tongue b16.5, lt cl. 300, 0a182 gr.f304 , bf, ss b16.5, lg cl. 600, 0a182 gr.f304 , bf, ss b16.5, lt cl. 600, 0a182 gr.f304 , bf flg, ss, large male facing b16.5, lm cl. 1500, 0a182 gr.f304 , bf flg, ss, large female facing b16.5, lf cl. 2500, 0a182 gr.f304 , bf flg, ss, large female facing b16.5, lf cl. 2500, 0a182 gr.f304 , bf, ss, ( nace ) b16.5, rtj cl. 1500, 0a 182 gr.f304l , bf, ss ( h2+nace ) b16.5, rtj cl. 2500, 0a182 gr. f321 , bf, ss ( h2+nace ) b16.5, rtj cl. 2500, 0a182 gr. f321 , bf, ss ( h2+nace ) b16.5, rtj cl. 2500, 0a182 gr. f321 , bf, ss ( h2+nace ) b16.5, rtj cl. 2500, 0a182 gr. f321 , lj flg with stub end, ss b16.9 / b16.5 cl. 150, 0 bw end, sch 10s a105 / a403 gr.wp904l , lj flg with stub end, ss b16.9 / b16.5 cl. 150, 0 bw end, sch 10s a105 / a403 gr.wp904l , lj flg with stub end, ss b16.9 / b16.5 cl. 150, 0 bw end, sch 10s a105 / a403 wp904l wx , lj flg with stub end, ss b16.9 / b16.5 cl. 150, 0 bw end, sch 10s a105 / a403 wp904l wx , lj flg with stub end, ss b16.9 / b16.5 cl. 150, 0 bw end, sch 80s a105 / a403 gr.wp904l , lj flg with stub end, ss b16.9 / b16.5 cl. 300, 0 bw end, sch 40s a105 / a403 gr.wp904l , lj flg with stub end, ss b16.9 / b16.5 cl. 600, 0 bw end, sch 10s a105 / a403 gr.wp904l , sw flg, ss b16.5, rf cl. 300, 0 sw ends, sch 40s a182 gr.f304 , sw flg, ss b16.5, rf cl. 300, 0 sw ends, sch 40s a182 gr.f304 , sw flg, ss b16.5, rf cl. 300, 0 sw ends, sch 80s a182 gr.f304 , sw flg, ss b16.5, rf cl. 300, 0 sw ends, sch 80s a182 gr.f304 , sw flg, ss, ( nace ) b16.5, rf cl. 300, 0 sw end, sch 40s a182 gr.f304l , sw flg, ss, ( nace ) b16.5, rf cl. 300, 0 sw end, sch 40s a182 gr.f304l , sw flg, ss, ( nace ) b16.5, rf cl. 300, 0 sw end, sch 80s a182 gr.f304l , sw flg, ss b16.5 cl. 300, 0 sw end, sch 40s, rf a182 gr.f304 , sw flg, ss b16.5 cl. 300, 0 sw end, sch 40s, rf a182 gr.f304 , sw flg, ss ( h2 ser. ) b16.5 cl. 300, 0 sw end, sch 40s, rf a182 gr.f304 , sw flg, ss ( h2 ser. ) b16.5 cl. 300, 0 sw end, sch 40s, rf a182 gr.f304 , sw flg, ss b16.5 cl. 300, 0 sw end, sch 80s, rf a182 gr.f304 , sw flg, ss b16.5 cl. 300, 0 sw end, sch 80s, rf a182 gr.f304 , sw flg, ss ( h2 ser. ) b16.5 cl. 300, 0 sw end, sch 80s, rf a182 gr.f304 , sw flg, ss ( h2 ser. ) b16.5 cl. 300, 0 sw end, sch 80s, rf a182 gr.f304 , sw flg, ss b16.5 cl. 600, 0 sw end, sch 40s, rf a182 gr.f304 , sw flg, ss b16.5 cl. 600, 0 sw end, sch 40s, rf a182 gr.f304 , sw flg, ss, ( h2 ser. ) b16.5 cl. 600, 0 sw end, sch 40s, rf a182 gr.f304 , sw flg, ss, ( h2 ser. ) b16.5 cl. 600, 0 sw end, sch 40s, rf a182 gr.f304 , sw flg, ss b16.5 cl. 600, 0 sw end, sch 80s, rf a182 gr.f304 , sw flg, ss b16.5 cl. 600, 0 sw end, sch 80s, rf a182 gr.f304 , sw flg, ss, ( h2 ser. ) b16.5 cl. 600, 0 sw end, sch 80s, rf a182 gr.f304 , sw flg, ss, ( h2 ser. ) b16.5 cl. 600, 0 sw end, sch 80s, rf a182 gr.f304 , sw flg, ss b16.5 cl. 300, 0 sw end, sch 40s, rf a182 gr.f316 , sw flg, ss b16.5 cl. 300, 0 sw end, sch 40s, rf a182 gr.f316 , sw flg, ss b16.5 cl. 300, 0 sw end, sch 80s, rf a182 gr.f316 , sw flg, ss b16.5 cl. 300, 0 sw end, sch 80s, rf a182 gr.f316 , sw flg, ss, ( nace ) b16.5 cl. 300, 0 sw end, sch 40s, rf a182 gr.f321 , sw flg, ss, ( nace ) b16.5 cl. 300, 0 sw end, sch 80s, rf a182 gr.f321 , adaptor, flgd, ss pinles pip 6265 a182 gr.f304 , adaptor, flgd, ss pinles pip 6265 a182 gr.f304 , adaptor, ss pinles pip 6265 a182 gr.f304 , supply of flange and adaptor ltcs ( low temprature carbon steel ) ( cpmsl cat1.156 as per nov 2022 ) , welding neck flange, ltcs b16.5 cl. 150, 0 bw end, sch std, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 150, 0 bw end, sch std, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 150, 0 bw end, sch std, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 150, 0 bw end, sch std, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 150, 0 bw end, sch std, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 150, 0 bw end, sch std, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 150, 0 bw end, sch xs, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 150, 0 bw end, sch xs, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 150, 0 bw end, sch xs, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 150, 0 bw end, sch 160, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 150, 0 bw end, sch 160, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 300, 0 bw end, sch std, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 300, 0 bw end, sch std, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 300, 0 bw end, sch std, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 300, 0 bw end, sch std, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 300, 0 bw end, sch std, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 300, 0 bw end, sch std, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 300, 0 bw end, sch xs, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 300, 0 bw end, sch xs, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 300, 0 bw end, sch xs, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 300, 0 bw end, sch xs, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.47sr b cl. 300, 0 bw end, sch xs, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.47 sr.b cl. 300, 0 bw end, 17.48 thk, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 600, 0 bw end, sch std, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 600, 0 bw end, sch std, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 600, 0 bw end, sch std, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 600, 0 bw end, sch std, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 600, 0 bw end, sch std, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 600, 0 bw end, sch xs, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 600, 0 bw end, sch xs, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 600, 0 bw end, sch xs, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 600, 0 bw end, sch xs, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 600, 0 bw end, sch xs, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 600, 0 bw end, sch xs, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 600, 0 bw end, sch xs, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 600, 0 bw end, sch xs, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 900, 0 bw end, sch std, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 900, 0 bw end, sch xs, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 900, 0 bw end, sch xs, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 1500, 0 bw end, sch xs, rf a350 gr.lf2 cl.1 , welding neck flange, ltcs b16.5 cl. 1500, 0 bw end, sch 160, rf a350 gr.lf2 cl.1 , wn flg, ltcs, b16.5, rf cl. 900, 0 bw ends, sch std a350 gr.lf2 cl1 , blind flange, ltcs b16.5 cl. 150, 0 rf a350 gr.lf2 cl.1 , blind flange, ltcs b16.5 cl. 150, 0 rf a350 gr.lf2 cl.1 , blind flange, ltcs b16.5 cl. 150, 0 rf a350 gr.lf2 cl.1 , blind flange, ltcs b16.5 cl. 150, 0 rf a350 gr.lf2 cl.1 , blind flange, ltcs b16.5 cl. 300, 0 rf a350 gr.lf2 cl.1 , blind flange, ltcs b16.5 cl. 300, 0 rf a350 gr.lf2 cl.1 , blind flange, ltcs b16.5 cl. 300, 0 rf a350 gr.lf2 cl.1 , blind flange, ltcs b16.5 cl. 300, 0 rf a350 gr.lf2 cl.1 , blind flange, ltcs b16.5 cl. 300, 0 rf a350 gr.lf2 cl.1 , blind flange, ltcs b16.5 cl. 300, 0 rf a350 gr.lf2 cl.1 , blind flange, ltcs b16.5 cl. 300, 0 rf a350 gr.lf2 cl.1 , blind flange, ltcs b16.5 cl. 300, 0 rf a350 gr.lf2 cl.1 , blind flange, ltcs b16.5 cl. 300, 0 rf a350 gr.lf2 cl.1 , blind flange, ltcs b16.5 cl. 600, 0 rf a350 gr.lf2 cl.1 , blind flange, ltcs b16.5 cl. 600, 0 rf a350 gr.lf2 cl.1 , blind flange, ltcs b16.5 cl. 600, 0 rf a350 gr.lf2 cl.1 , blind flange, ltcs b16.5 cl. 600, 0 rf a350 gr.lf2 cl.1 , blind flange, ltcs b16.5 cl. 600, 0 rf a350 gr.lf2 cl.1 , sw flg, ltcs b16.5 cl. 300, 0 sw end, sch xs, rf a350 gr.lf2 cl.1 , sw flg, ltcs b16.5 cl. 300, 0 sw end, sch xs, rf a350 gr.lf2 cl.1 , sw flg, ltcs b16.5 cl. 300, 0 sw end, sch 160, rf a350 gr.lf2 cl.1 , sw flg, ltcs b16.5 cl. 300, 0 sw end, sch 160, rf a350 gr.lf2 cl.1 , sw flg, ltcs b16.5 cl. 600, 0 sw end, sch xs, rf a350 gr.lf2 cl.1 , sw flg, ltcs b16.5 cl. 600, 0 sw end, sch xs, rf a350 gr.lf2 cl.1 , sw flg, ltcs b16.5 cl. 600, 0 sw end, sch 160, rf a350 gr.lf2 cl.1 , sw flg, ltcs b16.5 cl. 600, 0 sw end, sch 160, rf a350 gr.lf2 cl.1 , sw flg, ltcs b16.5 cl. 1500, 0 sw end, sch xs, rf a350 gr.lf2 cl.1 , adaptor, ltcs pinles pip 6265 a350 gr.lf2 cl.1 , adaptor, ltcs pinles pip 6265 a350 gr.lf2 cl.1 => limited...

Haryana Power Generation Corporation Limited - Haryana

34523905 supply of spares of coal mills ( hp 1103 ) to rgtpp khedar hisar on annual rate contract basis. , supply of spares of coal mills ( hp 1103 ) to rgtpp khedar hisar on annual rate contract basis , journal housing seal cover for journal assembly of coal mill moc: is1020 cast steel / en 24 , journal housing liner upper, moc: cast steel as per is 1030 grade 2 , journal housing liner lower, moc ss 304 , scrapper with liner plate long, moc: is 1030, gr ii, ( cast steel ) moc of liner: iss 276 astm grade 3 , scrapper with liner plate, short, moc:is 1030, gr ii, ( cast steel ) moc of liner: iss 276 astm grade 3 , feeder outlet gate without actuator , roller liner device for coal mill , ventury for coal mill , ventury vane for coal mill, hardness 60 to 62 hrc, thickness 15mm, ( 1set= 4 nos. ) , air restriction ring large size ( length approx. 1800mm, width 60mm, thickness 28mm ) ( 1 set=8 nos. ) , air restriction ring small size ( length approx. 1800mm, width 35mm, thickness 28mm ) ( 1 set= 8 nos. ) , mill body deflector support plate ms, ( 1 set= 3 nos. ) , metallic expansion bellow for pf piping, 2 nos. congulation, ss 304, 2 mm thick, od: 710 mm , dresser coupling for center feed pipe of coal mill , eccentric bearing housing for rc feeder , bearing housing for rc feeder and coal mill gt1651907 , bearing housing left for rc feeder model: cs2036gt1630407 , bearing housing right for rc feeder model: cs2036gt1630607 , clean out conveyor chain with scrapper, moc: cast alloy steel, pin: en 08, ( 1 set= 82 pieces ) , 72 chain links and 10 chain scrapper , screw stem for belt tightening, moc ss 316 , idler roller for rc feeder model:cs2036, ( 1 set=12 nos. ) , bushing for rc feeder and coal millgt1651807 , bearing housing assembly & rode housing assembly for rc feeder and coal millgt1632107 , seals of hot shut off gate l2000 mm, width 115mm, thickness 1.5mm, moc ss 304 , seals of hot shut off gate l1800mm, width 115mm, thickness 1.5mm, moc ss 304 , multiport outlet ( mpo ) for coal mill ceramic tile from inside. moc ms, specification of ceramic tile: thickness 12 mm, weldable with plug, alumina content more than 90%, hardness more than 8 on mohs scale, colour white, bulk density more than tha 3.2 gm / cc, water absorption less than 0.5%, cold cushing strength more than 3000kg / cm2, flexural strength ( at room temperature ) more 2200kg / cm2, flow medium is pulverized coal mixture , feeder outlet hopper of rc feeder , skirt assembly, ( 1 set = 4 nos. ) , shroud plate 1360x120x10 mm moc ms ( 1 set = 8 nos. ) , wearable adjustable shrink ( adjustable orifice ) spares for coal mill ( hp 1103 ) , coal pipe, od 710 mm, model smk type sb , three dimensional wearable elbow no. 29 ( drawing no. 50 f288s j0502 37 ) , vane wheel segment for coal mill ( hp 1103 ) ( 1 set = 8 nos. ) , mill bowl hub clamping ring moc 16 mn ( 1 set = 4 nos. ) , cover for hot air diaphragm, moc aluminium , coupling for cleanout conveyor for rc feeder , roller retainer ring for coal mills for rc feeder...

Northern Railway - Haryana

34415501 supply of chain sling of alloy steel with sling hookschain sling of alloy steel with sling hooks, chain sling of alloy steel with sling hooks ( hook dia 24mm for lifting rmpu ) , of 4 legs ( each of length 2mtr ) , load capacity minimum 2.0 ton of grade 80 or 100. along with test certificate from nabl approved lab...

Indian Oil Corporation Limited - Haryana

34322829 supply of block forged fittings for cdw and pp units supply of block forged fittings for cdw and pp units , supply of fittings forged carbon steel ( cpmsl cat1.47 as per oct 2022 ) , latrolet, cs mfg std sw ends a105 , latrolet, cs mfg std sw ends a105 , latrolet, ltcs mfg std sw ends a350 lf2 cl1 , swage con, cs bs 3799 pbe, sch xs a105 , swage con, cs bs 3799 pbe, sch xs a105 , swage con, cs, ( nace ) bs 3799 pbe, sch xs a105 , swage con, cs bs 3799 pbe, sch 160 a105 , swage con, cs bs 3799 pbe, sch 160 a105 , swage con, cs ( nace ) bs 3799 pbe, sch 160 a105 , swage con, cs, ( nace ) bs 3799 pbe, sch 160 a105 , swage con, cs, ( gi ) mnpt x mnpt bs 3799 pbe, sch xxs a105 , swage con, ltcs bs 3799 small pe & large bw end, sch xs a350 gr.lf2 cl.1 , swage con, ltcs bs 3799 small pe & large bw end, sch xs a350 gr.lf2 cl.1 , swage con, ltcs bs 3799 pbe, sch xs a350 gr.lf2 cl.1 , swage con, ltcs bs 3799 pbe, sch 160 a350 gr.lf2 cl.1 , swage con, cs, ( ibr ) bs 3799 pbe, sch 160 a105 , swage ecc, cs bs 3799 pbe, sch xs a105 , swage ecc, cs bs 3799 pbe, sch xs a105 , swage ecc, ltcs, bs 3799 small pe& large bw end, sch std a350 gr.lf2 cl.1 , swage ecc, ltcs, bs 3799 small pe & large bw end, sch xs a350 gr.lf2 cl.1 , swage ecc, ltcs, bs 3799 small pe & large bw end, sch xs a350 gr.lf2 cl.1 , swage ecc, ltcs bs 3799 pbe, sch xs a350 gr.lf2 cl.1 , swage ecc, ltcs bs 3799 pbe, sch xs a350 gr.lf2 cl.1 , swage ecc, ltcs bs 3799 pbe, sch xs a350 gr.lf2 cl.1 , elb, 90 deg, cs b16.11 sw ends a105 , elb, 90 deg, cs b16.11 sw ends a105 , elb, 90 deg, cs ( nace ) b16.11 sw ends a105 , elb, 90 deg, cs ( nace ) b16.11 sw ends a105 , elb, 90 deg, cs b16.11 sw ends a105 , elb, 90 deg, cs b16.11 sw ends a105 , elb, 90 deg, cs b16.11 sw ends a105 , elb, 90 deg, cs ( nace ) b16.11 sw ends a105 , elb, 90 deg, cs ( nace ) b16.11 sw ends a105 , elb, 90 deg, cs ( nace ) b16.11 sw ends a105 , elb, 90 deg, cs ( nace ) b16.11 sw ends a105 , elb, 90 deg, cs b16.11 sw ends a105 , elb, 90 deg, cs ( nace ) b16.11 sw ends a105 , elb, 90 deg, ltcs b16.11 sw ends a350 gr.lf2 cl.1 , elb, 90 deg, ltcs b16.11 sw ends a350 gr.lf2 cl.1 , elb, 90 deg, ltcs b16.11 sw ends a350 gr.lf2 cl.1 , elb, 90 deg, ltcs b16.11 sw ends a350 gr.lf2 cl.1 , elb, 90 deg, cs ( ibr ) b16.11 sw ends a105 , elb, 90 deg, cs ( ibr ) b16.11 sw ends a105 , elb, 90 deg, cs ( ibr ) b16.11 sw ends a105 , elb, 90 deg, cs ( ibr ) b16.11 sw ends a105 , elb, 45 deg, cs b16.11 sw ends a105 , elb, 45 deg, cs b16.11 sw ends a105 , elb, 45 deg, cs ( nace ) b16.11 sw ends a105 , elb, 45 deg, cs b16.11 sw ends a105 , elb, 45 deg, cs b16.11 sw ends a105 , elb, 45 deg, ltcs b16.11 sw ends a350 gr.lf2 cl.1 , elb, 45 deg, ltcs b16.11 sw ends a350 gr.lf2 cl.1 , elb, 45 deg, ltcs b16.11 sw ends a350 gr.lf2 cl.1 , elb, 45 deg, ltcs b16.11 sw ends a350 gr.lf2 cl.1 , elb, 45 deg, cs ( ibr ) b16.11 sw ends a105 , elb, 45 deg, cs ( ibr ) b16.11 sw ends a105 , elb, 45 deg, cs ( ibr ) b16.11 sw ends a105 , elb, 45 deg, cs ( ibr ) b16.11 sw ends a105 , fcpl, cs ( nace ) b16.11 sw ends a105 , fcpl, cs ( nace ) b16.11 sw ends a105 , fcpl, cs b16.11 sw ends a105 , fcpl, cs ( ibr ) b16.11 sw ends a105 , rcpl, cs mfg std sw ends to b16.11 a105 , rcpl, cs mfg std sw ends to b16.11 a105 , rcpl, cs mfg std sw ends to b16.11 a105 , rcpl, cs mfg std sw ends to b16.11 a105 , rcpl, cs mfg std sw ends to b16.11 a105 , rcpl, cs ( nace ) mfg std sw ends to b16.11 a105 , rcpl, cs mfg std sw ends to b16.11 a105 , rcpl, cs ( nace ) mfg std sw ends to b16.11 a105 , rcpl, cs ( nace ) mfg std sw ends to b16.11 a105 , rcpl, ltcs b16.11 sw ends a350 gr.lf2 cl.1 , rcpl, ltcs b16.11 sw ends a350 gr.lf2 cl.1 , rcpl, ltcs b16.11 sw ends a350 gr.lf2 cl.1 , rcpl, ltcs b16.11 sw ends a350 gr.lf2 cl.1 , rcpl, ltcs b16.11 sw ends a350 gr.lf2 cl.1 , rcpl, cs ( ibr ) mfg std sw ends to b16.11 a105 , rcpl, cs ( ibr ) mfg std sw ends to b16.11 a105 , rcpl, cs ( ibr ) mfg std sw ends to b16.11 a105 , rcpl, cs ( ibr ) mfg std sw ends to b16.11 a105 , rcpl, cs ( ibr ) mfg std sw ends to b16.11 a105 , tee, cs b16.11 sw ends a105 , tee, cs b16.11 sw ends a105 , tee, cs b16.11 sw ends a105 , tee, cs ( nace ) b16.11 sw ends a105 , tee, cs ( nace ) b16.11 sw ends a105 , tee, cs b16.11 sw ends a105 , tee, cs b16.11 sw ends a105 , tee, cs b16.11 sw ends a105 , tee, cs b16.11 sw ends a105 , tee, cs b16.11 sw ends a105 , tee, cs b16.11 sw ends a105 , tee, cs b16.11 sw ends a105 , tee, cs ( nace ) b16.11 sw ends a105 , tee, cs ( nace ) b16.11 sw ends a105 , tee, cs ( nace ) b16.11 sw ends a105 , tee, cs ( nace ) b16.11 sw ends a105 , tee, cs ( nace ) b16.11 sw ends a105 , tee, cs b16.11 sw ends a105 , tee, cs ( nace ) b16.11 sw ends a105 , tee, cs ( nace ) b16.11 sw ends a105 , tee, ltcs b16.11 sw ends a350 gr.lf2 cl.1 , tee, ltcs b16.11 sw ends a350 gr.lf2 cl.1 , tee, ltcs b16.11 sw ends a350 gr.lf2 cl.1 , tee, ltcs b16.11 sw ends a350 gr.lf2 cl.1 , tee, ltcs b16.11 sw ends a350 gr.lf2 cl.1 , tee, ltcs b16.11 sw ends a350 gr.lf2 cl.1 , tee, ltcs b16.11 sw ends a350 gr.lf2 cl.1 , tee, ltcs b16.11 sw ends a350 gr.lf2 cl.1 , tee, ltcs b16.11 sw ends a350 gr.lf2 cl.1 , tee, cs ( ibr ) b16.11 sw ends a105 , tee, cs ( ibr ) b16.11 sw ends a105 , tee, cs ( ibr ) b16.11 sw ends a105 , tee, cs ( ibr ) b16.11 sw ends a105 , tee, cs ( ibr ) b16.11 sw ends a105 , tee, cs ( ibr ) b16.11 sw ends a105 , tee, cs ( ibr ) b16.11 sw ends a105 , tee, cs ( ibr ) b16.11 sw ends a105 , tee, cs ( ibr ) b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs, ( nace ) b16.11 sw ends a105 , hcpl, cs, ( nace ) b16.11 sw ends a105 , hcpl, cs, ( nace ) b16.11 sw ends a105 , hcpl, cs, ( nace ) b16.11 sw ends a105 , hcpl, cs, ( nace ) b16.11 sw ends a105 , hcpl, cs, ( nace ) b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs, ( nace ) b16.11 sw ends a105 , hcpl, cs, ( nace ) b16.11 sw ends a105 , hcpl, cs, ( nace ) b16.11 sw ends a105 , hcpl, cs, ( nace ) b16.11 sw ends a105 , hcpl, cs, ( nace ) b16.11 sw ends a105 , hcpl, cs, ( nace ) b16.11 sw ends a105 , hcpl, cs, ( nace ) b16.11 sw ends a105 , hcpl, cs, ( nace ) b16.11 sw ends a105 , hcpl, cs, ( nace ) b16.11 sw ends a105 , hcpl, cs, ( nace ) b16.11 sw ends a105 , hcpl, cs, ( nace ) b16.11 sw ends a105 , hcpl, cs, ( nace ) b16.11 sw ends a105 , hcpl, cs b16.11 sw ends a105 , hcpl, cs, ( nace ) b16.11 sw ends a105 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, ltcs b16.11 sw ends a350, lf2, cl1 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , hcpl, cs, ( ibr ) b16.11 sw ends a105 , elb, 90 deg, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , elb, 90 deg, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , elb, 90 deg, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , elb, 90 deg, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , elb, 90 deg, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , elb, 90 deg, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , elb, 90 deg, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , elb, 45 deg, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , elb, 45 deg, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , elb, 45 deg, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , elb, 45 deg, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , elb, 45 deg, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , elb, 45 deg, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , thredolet, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , thredolet, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , thredolet, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , thredolet, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , thredolet, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , thredolet, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , thredolet, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , thredolet, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , thredolet, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , thredolet, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , thredolet, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , thredolet, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , thredolet, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , thredolet, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , thredolet, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , thredolet, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , thredolet, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , thredolet, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , fcpl, cs b16.11 scrd ends, npt ( f ) a105 , fcpl, cs, ( nace ) b16.11 scrd ends, npt ( f ) a105 , fcpl, cs b16.11 scrd ends, npt ( f ) a105 , fcpl, cs ( nace ) b16.11 scrd ends, npt ( f ) a105 , fcpl, ltcs b16.11 scrd ends, npt ( f ) a350 gr.lf2, cl1 , fcpl, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , fcpl, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , fcpl, cs ( ibr ) b16.11 scrd ends, npt ( f ) a105 , rcpl, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , rcpl, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , rcpl, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , rcpl, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , rcpl, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , tee, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , tee, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , tee, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , tee, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , tee, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , tee, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , tee, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , tee, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , tee, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , tee, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , tee, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , tee, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , tee, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , tee, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , tee, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , tee, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , tee, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , tee, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , tee, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , tee, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , tee, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , union, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , union, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , union, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , union, cs ( galv ) b16.11 scrd ( f ) , b1.20.1 a105 ( galv ) , supply of fittings forged alloy steel ( cpmsl cat1.48 as per oct 2022 ) , elb, 90 deg, as b16.11 sw ends a182 gr.f9 , fcpl, as b16.11 sw ends a182 gr.f9 , tee, as b16.11 sw ends a182 gr.f9 , hcpl, as b16.11 sw ends a182 gr.f9 , supply of fittings forged stainless steel ( cpmsl cat 1.49 as per oct 2022 ) , swage con, ss bs 3799 pbe, sch 80s a182 gr f304 , swage con, ss ( h2 ser. ) bs 3799 pbe, sch 80s a182 gr f304 , swage con, ss bs 3799 pbe, sch 80s a182 gr.f304 , swage con, ss bs 3799 pbe, sch 80s a182 gr.f316 , elb, 90 deg, ss b16.11 sw ends a182 gr.f304 , elb, 90 deg, ss b16.11 sw ends a182 gr.f304 , elb, 90 deg, ss b16.11 sw ends a182 gr.f304 , elb, 90 deg, ss b16.11 sw ends a182 gr.f304 , elb, 90 deg, ss ( h2 ser. ) b16.11 sw ends a182 gr.f304 , elb, 90 deg, ss ( h2 ser. ) b16.11 sw ends a182 gr.f304 , elb, 90 deg, ss ( h2 ser. ) b16.11 sw ends a182 gr.f304 , elb, 90 deg, ss ( h2 ser. ) b16.11 sw ends a182 gr.f304 , elb, 90 deg, ss b16.11 sw ends a182 gr.f316 , elb, 90 deg, ss b16.11 sw ends a182 gr.f316 , elb, 90 deg, ss b16.11 sw ends a182 gr.f316 , elb, 90 deg, ss b16.11 sw ends a182 gr.f316 , elb, 45 deg, ss b16.11 sw ends a182 gr. f304 , elb, 45 deg, ss b16.11 sw ends a182 gr. f304 , elb, 45 deg, ss ( h2 ser. ) b16.11 sw ends a182 gr.f304 , elb, 45 deg, ss ( h2 ser. ) b16.11 sw ends a182 gr.f304 , elb, 45 deg, ss ( h2 ser. ) b16.11 sw ends a182 gr.f304 , elb, 45 deg, ss b16.11 sw ends a182 gr.f316 , elb, 45 deg, ss b16.11 sw ends a182 gr.f316 , fcpl, ss, threaded ends, ( f ) npt b16.11 threaded ends, npt ( f ) astm a182 f304 , fcpl, ss ( nace ) b16.11 sw ends a182 gr.f321 , rcpl, ss mss sp95 / mf std sw ends to b16.11 a182 gr.f304 , rcpl, ss mss sp95 / mf std sw ends to b16.11 a182 gr.f304 , rcpl, ss mss sp95 / mf std sw ends to b16.11 a182 gr.f304 , rcpl, ss mss sp95 / mf std sw ends to b16.11 a182 gr.f304 , rcpl, ss mss sp95 / mf std sw ends to b16.11 a182 gr.f304 , rcpl, ss mss sp95 / mf std sw ends to b16.11 a182 gr.f304 , rcpl, ss ( h2 ser. ) b16.11 sw ends a182 gr.f304 , rcpl, ss ( h2 ser. ) b16.11 sw ends a182 gr.f304 , rcpl, ss b16.11 sw ends a182 gr.f316 , rcpl, ss b16.11 sw ends a182 gr.f316 , rcpl, ss b16.11 sw ends a182 gr.f316 , rcpl, ss, ( nace ) b16.11 sw ends a182 gr.f321 , tee, ss b16.11 sw ends a182 gr.f304 , tee, ss b16.11 sw ends a182 gr.f304 , tee, ss b16.11 sw ends a182 gr.f304 , tee, ss b16.11 sw ends a182 gr.f304 , tee, ss b16.11 sw ends a182 gr.f304 , tee, ss b16.11 sw ends a182 gr.f304 , tee, ss b16.11 sw ends a182 gr.f304 , tee, ss b16.11 sw ends a182 gr.f304 , tee, ss b16.11 sw ends a182 gr.f304 , tee, ss ( h2 ser. ) b16.11 sw ends a182 gr.f304 , tee, ss ( h2 ser. ) b16.11 sw ends a182 gr.f304 , tee, ss ( h2 ser. ) b16.11 sw ends a182 gr.f304 , tee, ss ( h2 ser. ) b16.11 sw ends a182 gr.f304 , tee, ss ( h2 ser. ) b16.11 sw ends a182 gr.f304 , tee, ss ( h2 ser. ) b16.11 sw ends a182 gr.f304 , tee, ss ( h2 ser. ) b16.11 sw ends a182 gr.f304 , tee, ss ( h2 ser. ) b16.11 sw ends a182 gr.f304 , tee, ss ( h2 ser. ) b16.11 sw ends a182 gr.f304 , tee, ss, ( nace ) b16.11 sw ends a182 gr.f304l , tee, ss b16.11 sw ends a182 gr.f316 , tee, ss b16.11 sw ends a182 gr.f316 , tee, ss b16.11 sw ends a182 gr.f316 , tee, ss b16.11 sw ends a182 gr.f316 , tee, ss b16.11 sw ends a182 gr.f316 , tee, ss, ( nace ) b16.11 sw ends a182 gr.f321 , half coupling, ss b16.11 sw ends a182 gr.f304 , half coupling, ss b16.11 sw ends a182 gr.f304 , half coupling, ss b16.11 sw ends a182 gr.f304 , half coupling, ss b16.11 sw ends a182 gr.f304 , half coupling, ss b16.11 sw ends a182 gr.f304 , half coupling, ss b16.11 sw ends a182 gr.f304 , half coupling, ss b16.11 sw ends a182 gr.f304 , half coupling, ss b16.11 sw ends a182 gr.f304 , half coupling, ss b16.11 sw ends a182 gr.f304 , half coupling, ss b16.11 sw ends a182 gr.f304 , half coupling, ss b16.11 sw ends a182 gr.f304 , half coupling, ss b16.11 sw ends a182 gr.f304 , half coupling, ss b16.11 sw ends a182 gr.f304 , half coupling, ss b16.11 sw ends a182 gr.f304 , half coupling, ss b16.11 sw ends a182 gr.f304 , half coupling, ss b16.11 sw ends a182 gr.f304 , half coupling, ss, ( nace ) b16.11 sw ends a182 gr.f304l , half coupling, ss, ( nace ) b16.11 sw ends a182 gr.f304l , hcpl, ss b16.11 sw end a182 gr.f316 , hcpl, ss b16.11 sw end a182 gr.f316 , hcpl, ss b16.11 sw end a182 gr.f316 , hcpl, ss b16.11 sw end a182 gr.f316 , hcpl, ss, ( nace ) b16.11 sw end a182 gr.f321 , fcpl, ss b16.11 scrd ends, npt ( f ) a182 gr.f304 , fcpl, ss, ( h2 service ) b16.11 scrd ends, npt ( f ) a182 gr.f304 , fcpl, ss b16.11 scrd ends, npt ( f ) a182 gr.f316 , supply of weldolets / sockolets / elbowletl ( cpmsl cat 1.50 as per oct 2022 ) , wlet, cs ( h2 service ) mss sp 97 bw ends, sch xs a105 , wlet, cs ( h2 service ) mss sp 97 bw ends, sch xs a105 , wlet, cs ( h2 service ) mss sp 97 bw ends, sch xs a105 , wlet, cs mss sp 97 bw ends, sch 160 a105 , wlet, cs mss sp 97 bw ends, sch 160 a105 , wlet, cs mss sp 97 bw ends, sch 160 a105 , wlet, cs ( h2 service ) mss sp 97 bw ends, sch 160 a105 , wlet, cs ( h2 service ) mss sp 97 bw ends, sch 160 a105 , wlet, cs ( h2 service ) mss sp 97 bw ends, sch 160 a105 , wlet, cs ( h2 service ) mss sp 97 bw ends, sch 160 a105 , wlet, cs ( h2 service ) mss sp 97 bw ends, sch 160 a105 , wlet, cs ( h2+nace ) mss sp 97 bw ends, sch 160 a105 , wlet, cs ( h2+nace ) mss sp 97 bw ends, sch 160 a105 , wlet, cs ( h2+nace ) mss sp 97 bw ends, sch 160 a105 , wlet, cs ( h2+nace ) mss sp 97 bw ends, sch 160 a105 , wlet, cs ( h2+nace ) mss sp 97 bw ends, sch 160 a105 , wlet, cs ( h2+nace ) mss sp 97 bw ends, sch 160 a105 , wlet, cs ( h2+nace ) mss sp 97 bw ends, sch 160 a105 , wlet, cs mss sp 97 bw ends, sch xxs a105 , wlet, cs mss sp 97 bw ends, sch xxs a105 , wlet, cs mss sp 97 bw ends, sch xxs a105 , wlet, cs mss sp 97 bw ends, sch xxs a105 , wlet, cs mss sp 97 bw ends, sch xxs a105 , wlet, cs mss sp 97 bw ends, sch xxs a105 , wlet, cs mss sp 97 bw ends, sch xxs a105 , wlet, cs mss sp 97 bw ends, sch xxs a105 , wlet, cs mss sp 97 bw ends, sch xxs a105 , wlet, cs mss sp 97 bw ends, sch xxs a105 , wlet, cs mss sp 97 bw ends, sch xxs a105 , wlet, cs ( h2+nace ) mss sp 97 bw ends, sch xxs a105 , wlet, cs ( h2+nace ) mss sp 97 bw ends, sch xxs a105 , wlet, cs ( h2+nace ) mss sp 97 bw ends, sch xxs a105 , wlet, cs ( h2+nace ) mss sp 97 bw ends, sch xxs a105 , wlet, cs ( h2+nace ) mss sp 97 bw ends, sch xxs a105 , wlet, cs ( h2+nace ) mss sp 97 bw ends, sch xxs a105 , wlet, cs ( h2+nace ) mss sp 97 bw ends, sch xxs a105 , wlet, cs ( h2+nace ) mss sp 97 bw ends, sch xxs a105 , wlet, cs ( h2+nace ) mss sp 97 bw ends, sch xxs a105 , wlet, cs ( h2+nace ) mss sp 97 bw ends, sch xxs a105 , wlet, cs ( nace ) mss sp 97 bw ends, sch xxs a105 , weldolet, ss, ( nace ) mss sp 97 bw ends, a182, gr.f304l , wlet, ss ( h2+nace ) mss sp 97 bw ends, sch 160 a182 gr.f321 , wlet, ss ( h2+nace ) mss sp 97 bw ends, sch 160 a182 gr.f321 , wlet, ss ( h2+nace ) mss sp 97 bw ends, sch 160 a182 gr.f321 , wlet, ss ( h2+nace ) mss sp 97 bw ends, sch 160 a182 gr.f321 , wlet, ss ( h2+nace ) mss sp 97 bw ends, sch xxs a182 gr.f321 , wlet, ss ( h2+nace ) mss sp 97 bw ends, sch xxs a182 gr.f321 , wlet, ss ( h2+nace ) mss sp 97 bw ends, sch xxs a182 gr.f321 , wlet, as ( h2+nace ) mss sp 97 bw ends, sch 160 a182 gr.f11 cl.2 , wlet, as ( h2+nace ) mss sp 97 bw ends, sch 160 a182 gr.f11 cl.2 , wlet, as ( h2+nace ) mss sp 97 bw ends, sch 160 a182 gr.f11 cl.2 , wlet, as ( h2+nace ) mss sp 97 bw ends, sch 160 a182 gr.f11 cl.2 , wlet, as ( h2+nace ) mss sp 97 bw ends, sch 160 a182 gr.f11 cl.2 , wlet, as ( h2+nace ) mss sp 97 bw ends, sch 160 a182 gr.f11 cl.2 , wlet, as ( h2+nace ) mss sp 97 bw ends, sch 160 a182 gr.f11 cl.2 , wlet, as ( h2+nace ) mss sp 97 bw ends, sch xxs a182 gr.f11 cl.2 , wlet, as ( h2+nace ) mss sp 97 bw ends, sch 160 a182 gr.f22 cl.3 , wlet, as ( h2+nace ) mss sp 97 bw ends, sch 160 a182 gr.f22 cl.3 , wlet, as ( h2+nace ) mss sp 97 bw ends, sch 160 a182 gr.f22 cl.3 , wlet, as ( h2+nace ) mss sp 97 bw ends, sch 160 a182 gr.f22 cl.3 , wlet, as ( h2+nace ) mss sp 97 bw ends, sch 160 a182 gr.f22 cl.3 , wlet, as ( h2+nace ) mss sp 97 bw ends, sch 160 a182 gr.f22 cl.3 => limited...

Northern Railway - Haryana

34295616 supply of alloy steel two legged chainalloy steel two legged chain, supply of alloy steel two legged chain sling with round ring on top to is: 2760 & 1 hook with welded construction joint to is: 3822, capacity 15 ton, length 6 mtr. along with test certificate from nabl approved lab....

Northern Railway - Haryana

34252499 supply of chain sling of alloy steel with sling hookschain sling of alloy steel with sling hooks, chain sling of alloy steel with sling hooks ( hook dia 24mm for lifting rmpu ) , of 4 legs ( each of length 2mtr ) , load capacity minimum 2.0 ton of grade 80 or 100. along with test certificate from nabl approved lab...

Panchayat Raj Department - Haryana

34153386 supply and installation of indoor & outdoor gym equipments at village nakora, himmatpur, rampura their and ranjitpur their block rania district sirsa ns itmes 2 providing, designing and fixing leg press size 153x137x152 cm fabricated with 2x4 rectangular hollow pipe with 3.00 mm thick and powder coated using akzo nobel or equivalent of 80 120 micron thick. all welding joints of pipe are well welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. zinc primer paint to be applied at all weldings points prior to finishing. handle bars are to be provided with high quality grip rubber at top end. padals shall be made upto of nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin lldpe manufactured by rotational moulding with minimum thickness of plastic 4.00 mm , colourful and u v resistant environmental friendly, bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by engineer in charge. equipment to be fitted within built limiters to prevent unwanted movements. all open ends of pipe to be coloured by gi / lldpe caps for user safety. the equipment to be fixed on ground with concrete of minimum strength m25 and j shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of engineer in charge regarding material, shape of equipment, colour on metal, seat and basecover plaste and fixing of equipment etc. 3 functional trainer machineall pipes made up size 2x4 of hot rolled hollow rectangular ms pipe with size 193x100x230 cm and powder coated using akzo nobel or equivalent of 80 120 micron thick. all welding joints of pipe are well welded with joints scalloped as neccessary and dressed of removing sharp edges and burrs. zinc primer paint to be applied at all welding points prior to finishing. handle bars are to be provided with high quality grip rubber. padals shall be made up of nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin lldpe manufactured by rotational moulding with minimum thickness of plastic 4.00, colourful and u v resistant environmental friendly, bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by engineer in charge. equipment to be fitted within built limiters to prevent unwanted movements. all open ends of pipe to be coloured by gi / lldpe caps for user safety. the equipment to be fixed on ground with concrete of minimum strength m25 and j shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of engineer in charge regarding material, shape of equipment, colour on metal, seat and base cover plaste and fixing of equipment etc. 4 multy gym six station ( leg pull, legh curl with leg extension, biceps with triceps, pec dec fly ) consists of 4 weighted stations and 2 light stations; and it is combination of 8 type of excersice this is made up of mainly olympic rectangular pipe of 4x2 with 2.15mm thickness with steel twisted wire with pvc / myloncoated cable 5mm 6mm; with pvc coated weight plates for noiseless working / movements, weight plates stack moves / slides in stainless steel pipes for smooth and noiseless movement throughout lifespan of equipments, ball bearing mouted fibre / pvcpullys, heavy cushion padding on 12mm plys with special non abrasive fabric nontearing fabric. each weight stackis 75 kg sheavy. 5 superior olympic bench flat ( made up of mainly olympic rectangular pipe of 4x2 approx.; more nearest to approx. 170x168x137 cm with 2.15mm thickness, heavy cushion padding on 12mm plys with special non abrasive fabric non tearing fabric. with two vertical pipes have clamp forresting rodonit, used for doing flatpattern chestpressat one fixed level ) 6 superior olympic bench incline ( made up of mainly olympic rectangular pipe of 4x2 approx.;more nearest to approx. 163x165x137 cm with 2.15mm thickness, heavy cushion padding on 12mm plys with special non abrasive fabric non tearing fabric. with two vertical pipes have clamp forresting robonit, used for doing incline level pattern chest press at one fixed incline level ) . 7 superior olympic bench deline ( made up of mainly olympic rectangular pipe of 4x2 approx.;more nearest to approx. 210x166x137 cm with 2.15 mm thickness, heavy cushion padding on 12mm plys with special non abrasive fabric non tearing fabric. with two vertical pipes have clamfor resting rod on it, used for doing decline level pattern chest press at one fixed decline level with leg locking ) 8 spare flat bench for dumbbell fly exercise ( made up of mainly olympic rectangular pipe of 4x2 approx.;more nearest to approx 121x75x46 cm with 2.15mm thickness, heavy cushion padding on 12mm plys with speical non abrasive fabric non teraring fabric. ) 9 cycleadjustable height & comfortable seat with cushions to prevent back aches & muscle stiffness.8 adjustable resistance levels & tension controller knob.material alloy steel. 6 months warranty. size ( l*b*h* ) ( 41*24*6 ) inches.dual action mode stationary & moving handles both. full body workout arms, calves, chest & back.belt based resistance mechanism allows better, momentum based recovery & better pedalling technique.suitable for high intensity cardio workout, weight loss, fully body workout & strangth training. 10 pull chariproviding designing and fixing of pull pair of size 25x800x2000 mm fabricated with main post of 140 mm disa and 3.00 mm thick and other pipes of 40 mm dia 3.00 mm thick all pipes made up of hot rolled tubular steel and powder coated using akzo nobel or equivalent of 80 120 micron thick. all welding joints of pipe are well welded with joints scalloped as necessary and dressed off removing sharp edges and burrs. zinc primer paint to be applied at all welding points prior to finishing. handle bars are to be provided with high quality grip rubber at top end. padals shall be made up of nylon alloy with rounded edge of prevent any impact of injury and seat to be made from virgin lldpe manufactured by rotational moulding with minimum thickness of plastic 4.00 mm, colourful and u v resistant environmental friendly. bearing used shall be maintenance free, duly oiled sealed and self lubricated made by reputed company to be approved by engineer in charge. equipment to be fitted within built limiters to prevent unwanted movements. all open ends of pipe to be coloured by gi / lldpe caps for user safety. the equipment to be fixed on ground with concrete of minimum strength m25 and j shaped welded bolts and once the concrete is set, fix the equipment on to it and cover nuts and bolts with the base plate cover, all complete as per direction and approval of engineer in charge regarding material, shape of equipment colours on metal, seat and base cover plate and fixing of equipment etc....

Indian Oil Corporation Limited - Haryana

34016616 bids are invited for tee,equal material: carbon steel manufacturing process: forged material specification: astm a105 end finish: socket weld end finish conform to ansi b16.11 dimension standard conform to ansi b16.11 additional requirements: nace certified nps , fittings,coupling,half material: stainless steel manufacturing process: forged material specification: astm a182 grade: f321 end finish: socket weld end finish conform to ansi b1.20.1 dimension standard conform to ansib16.11 nps , fittings,elbow,90 deg,long radius material: stainless steel manufacturing process: forged material specification: astm a182 grade: f321 end finish: socket weld end finish conform to ansi b1.20.1 dimension standard conform to ansib16.11, fittings,pipe,nipple material: carbon steel manufacturing process : seamless material specification: astm a106 grade: b class: end finish: scrd npt(f) x pe supplimentary requirement additional requirement: nps, fittings,cap material: carbon steel manufacturing process: forged material specification: astm a105 end finish: threaded dimension standard conform to ansib16.11 additional requirements: h2 service nps , fittings,elbow,45 deg,long radius material: carbon steel manufacturing process: seamless material specification: astm a234 grade: wpb end finish: butt weld end finish conform to ansi b16.25 dimension standard conform to ansi b16.9 nps , tee,equal material: carbon steel manufacturing process: seamless material specification: astm a420 grade: wp l6 end finish: butt weld end finish conform to ansi b16.25 dimension standard conform to ansi b16.9 nps , material: carbon steel manufacturing process: seamless material specification: astm a234 grade: wpb end finish: butt weld end finish conform to ansi b 16.25 dimension standard conform to ansi b16.9 nps , tee, unequal material: carbon steel manufacturing process: seamless material specification: astm a234 grade: wpb end finish: butt weld end finish conform to ansi b 16.25 dimension standard conform to ansi b 16.9 additional requirements: h2 service nps x nps, fittings,elbow,45 deg,long radius material: carbon steel manufacturing process: seamless material specification: astm a234 grade: wpb end finish: butt weld end finish conform to ansi b16.25 dimension standard conform to ansi b16.9 additional requirements: ibr certified nps , fittings,elbow,90 deg,short radius, material : carbon steel manufacturing process: seamless, galvanized material spec: astm a234 grade: wpb end finish: butt weld nps nps pressure rating [lbs] or schedule number inch mm, tee,unequal material: carbon steel manufacturing process: forged material specification: astm a105 end finish: threaded end finish conform to ansi b1.20.1 surface finish: galvanised dimension standard conform to ansib16.11 nps x nps, reducer,eccentric material: carbon steel manufacturing process: seamless material specification: astm a420 grade: wp l6 end finish: butt weld end finish conform to ansi b1.20.1 dimension standard conform to ansi b16.9 nps x nps , reducer,eccentric material: carbon steel manufacturing process: seamless material specification: astm a234 grade: wpb end finish: butt weld, end finish conform to ansi b16.25 dimension standard conform to ansi b16.9 nps x nps pressure rating [lbs] , fittings,elbow,90 deg,long radius material: carbon steel manufacturing process: seamless material specification: astm a234 grade: wpb end finish: butt weld end finish conform to ansi b16.25 dimension standard conform to ansi b16.9 additional requirements: ibr certified nps nps , fittings,elbow,45 deg,long radius material: carbon steel manufacturing process: seamless material specification: astm a234 grade: wpb end finish: butt weld end finish conform to ansi b16.25 dimension standard conform to ansi b16.9 additional requirements: ibr certified nps , tee,equal material: carbon steel manufacturing process: seamless material specification: astm a234 grade: wpb end finish: butt weld end finish conform to ansi b16.25, dimension standard conform to ansi b16.9 additional requirements: ibr certified nps ,reducer,eccentric material: carbon steel manufacturing process: welded material specification: astm a234 grade: wpb end finish: butt weld end finish conform to ansi b16.25 dimension standard conform to ansi b16.9 additional requirements: ibr certified nps x nps , fittings,elbow,90deg,long radius material: alloy steel manufacturing process: forged material specification: astm a182 grade: f11 end finish: socket weld end finish conform to ansi b1.20.1 dimension standard conform to ansib16.11 nps ...

Haryana Power Generation Corporation Limited - Haryana

33915912 supply of high pressure valve supply of high pressure valve , globe valve, 1” valve; forged carbon steel, astm sa 105, cl 2500, ends bw ; manual valve without actuator, design standard asme 16.34; ibr certified , globe valve, 1” valve; forged alloy steel, astm a182, gr f22, ci 3; cl 2500, ends bw; manual valve without actuator, design standard asme 16.34; ibr certified , globe valve, 1.5” valve; forged alloy steel, astm a182, gr f22, ci 3; cl 2500, ends bw; manual valve without actuator, design standard asme 16.34; ibr certified , globe valve, 1.5” valve; forged alloy steel, astm a182, gr f22, ci 3; cl 2500, ends bw; valves with motorized actuator suitable for on off type having mechanical limit switch arrangement, design standard asme 16.34; ibr certified; actuator type on & off with control cabinet for switching purpose from remote & local , globe valve, 2.0” valve; forged alloy steel, astma182, gr f22, ci 3; cl 4500, ends bw; valves with motorized actuator suitable for on off type having mechanical limit switch arrangement, design standard asme 16.34; ibr certified; actuator type on & off with control cabinet for switching purpose from remote & local...

Northern Railway - Haryana

33883372 supply of load cellload cell, load cell 65058 double ended shear beam. nickel plated alloy steel, capacity 15t suitable for 30mt digital make road weighbridge as per specifications in annexure a make sensortronics....