Military Engineer Services - Haryana

40431168 special repair to bldg. no. 200 ( block of 6 qtrs ) in cw lines andprovision ofsteel utensil rack in 118 x jcos / or govt md accnin cw lines & albert ekka line and provision of 50 xexhaust fans for jcos md accn in cw lines in the area ofage b / r i under ge ( n ) ambala cantt ; 1 schedule a part i ( b / r items ) taking down cement or cement lime plaster of any description on brick or stone walls etc including racking out joints, hacking for key scrubbing down with water etc complete all as specified and as directed by the engineer in charge. 2 demolition of brick work built in cement mortar or cement lime mortar including all quoins, arches, pillar etc but excluding ashlar facing, dressed stone work and precast concrete articles complete all as specified and as directed by the engr in charge. 3 m&lbrick work with sub class b old size bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete all as specified and as directed by the engineer in charge. 4 m&lbrick work with sub class b old size bricks straight or curved on plan to anyradius in half brick thick wall built in cement mortar 1:4 complete all as specified and as directed by the engineer in charge. 5 m & l rendering 15 mm thick on brick work or concrete wall surfaces in cement mortar 1:4including mixing water proofing compound @ 2% by weight of cement or as per manufacturers instruction and finished fair and even without using extra cement complete all as specified and as directed by the engineer in charge. ( wpc shall be measured and paid for separately ) 6 material and labour rendering 10 mm thick on any faces of brick work or concrete wall surfaces in cement mortar 1:6 andfinishedeven and fair without using extra cement complete all as specified and as directed by the engineer in charge. 7 supply only water proofing compound complete all as specified and as directed by the engineer in charge. 8 material and labour rendering 05 mm thick on fairfaces of brick work or concrete ceilingsurfaces in cement mortar 1:3 andfinishedeven and smooth without using extra cement complete all as specified and as directed by the engineer in charge. 9 m&l preparation of newly plastered / unplastered surfaces of walls and applying two coats of oil bound distemperwith painting roller over a coat of alkali resistant primer over and inlcuding 1mm to 2mm thick wall care putty white cement based in two or more coats to achive smooth surfacecomplete all as specified and as directed by the engineer in charge. 10 m & l complete removal of existing treatment on walls ( any number of layers ) by scrapping with steel scrappers or any other means, washing down with water to remove loose particles etc and applying two coats of oil bound distemperwith painting roller over a coat of alkali resistant primer over and including 1mm to 2mm thick wall care putty white cement based in two or more coats to achieve smooth surfacecomplete all as specified and as directed by the engineer in charge. 11 m&l preparation of new plastered / unplastered surfaces of brick / concrete ceiling and applying three coats of white lime wash complete all as specified and as directed by the engineer in charge. 12 m&l preparation of old decorated brick / concrete, plastered / un plastered surfaces ofceiling and applying two coats of white lime wash complete all as specified and as directed by the engineer in charge. 13 m&lpreparation of newly plastered surfaces of wall and applying two coats of cement based paint complete all as specified and as directed by the engineer in charge. 14 m & l complete removal of existing treatment on walls ( any number of layers ) by scrapping with steel scrappers or any other means, washing down with water to remove loose particles etc and applying two coats of cement base paint complete all as specified and as directed by the engineer in charge. 15 m & l complete removal of existing treatment on walls ( any number of layers ) by scrapping with steel scrappers or any other means, washing down with water to remove loose particles etc and applying two coats of 100% premium acrylic emulsion paint having voc less than 50 gm / litre and uv resistance as per is 15489:2004, alkali & fungal resistance, dirt resistance exterior paint of required shade ( company depot tinted ) with silicon additives @ 1.43 litre / 10 sqmover and including priming coat of exterior primer applied @ 0.90 litre per 10 sqmcomplete all as specified and as directed by the engineer in charge. 16 dismantling floor, hearth or wall tiling including cement mortar bedding ( but not backing ) , removing servicable tiles to store and rubbish off the premises complete all as specified and as directed by the engineer in charge. 17 m & l25 mm thick pcc 1:2:4, type b0 as in sub base of floor ( using 12.50mm gradedcrushed stone aggregate ) , finished even & fair without using extra cement complete all as specified and as directed by the engr in charge. 18 m&lnon skid coloured ceramic tiles joint freepremium / 1st quality 7 to 8 mm thick, ( square / rectangular ) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over andinculding15mm thick screed bed in cm 1:6 complete all as specified and as directed by the engineer in charge. 19 m&lnon skid coloured ceramic tiles joint free premium / 1st quality of same description as of floor tiles in serial item no18 abovebut 100mm to 200mm heightas in skirting, set and jointed in neat cement slurry and pointed in white or colouredcement mixed with pigmentto match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4complete all as specified and as directed by the engineer in charge. 20 material and labour glazed ceramic coloured tiles joint free 1st quality in vertical surfaces / skirtings / dados of size 450x300x7mm thick / 300 x 600 x 7 mm thickor nearest size as required , set and jointed in neat cement slurry and pointed in white or colouredcement mixed with pigmentto match over and including 10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:4complete all as specified and as directed by the engineer in charge. 21 m&lnon skid coloured ceramic tiles joint freepremium / 1st quality 7 to 8 mm thick, ( square / rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over andincluding15mm thick screed bed in cm 1:6 complete all as specified and as directed by the engineer in charge. 22 material and labour for marble work, baroda green, 16 18mm thick, in one piece in width and length not less than 1.8 m ( except in case of slab is more than 1.80 meter and less than 2.40 meter smaller size as approved by engr in charge may be used ) table rubbed & polished in shelves, coocking plateform, tread of stair case, window cill and similar locationetc including 15mm thick bedding layer in cement mortar ( 1:4 ) including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match with marble including rounding of exposed edges and finally granite finish polishing complete all as specified and as directed by the engineer in charge. 23 m & l formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum mers, lintels, cantilevers, shelves including supports overhangs etc, also splays between floors and beams, chajjas including edges etc., work in rough finished flat surfaces of concrete complete all as specified and as directed by the engineer in charge. 24 demolition of reinforced cement concrete in roofs, floors, beams, chajjas, staircases, landings and similar suspended work ( reinforcement cut as required to facilitate demolition ) complete all as specified and as directed by the engineer in charge. 25 m & l reinforced cement concrete 1:1 1 / 2:3 ( nominal mix ) using 20mm graded crushed stone aggregates as inchajjas, beams, lintels over 1.5 mtr spanand the like complete all as specified and as directed by the engineer in charge. 26 m & lprovidingpcc precast 1:2:4 type b1 using 20mm gradedcrushed stone aggregate as in landings, precast cover slabs ( for manholes etc. ) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including chamfers, weathering, throating etc and setting in cement mortar1:4 complete with joints to match, complete all as specified and as directed by the engineer in charge. 27 m & lmild steel framed work such as grills, gratings, etc. with ends of bars shouldered and / or riveted or forged into spikes, framed guard bars, barred iron doors, ladders, walk ways, railingsconforming to fe.290.gde e 165 complete all as specified and as directed by the engineer in charge. 28 m anti corrosive paint over a coat of red oxide primer bothinternally and externally ) including provision of new covered plate over sunken box for housing themodular switches , modular socket outlets, modularfan regulators etc.for one light / fan / exhaust fan point controlledby one way switch, complete all as specified and as directedby engineer in charge. note : a ) .all chases will be cut by chase cutter only b ) switch, socket outlet and fan regulators to be measured and paid forseparately . 126 description same all as per item no.125but for one 3 pin, 5 amps, socket outlet controlled by one switch on independent board, complete all as specified and as directedby engineer in charge. 127 description same allas per item no. 125 but for one 3 pin 5 amps socket outlet controlled by one switch on same board, complete all as specified and as directedby engineer in charge. 128 description same all as per item no.125butone light point controlled by two way switch complete all as specified and as directedby engineer in charge. 129 description same all as per srl item no 125 here in before but for one socket outlet 15 amp with 2.50 sq mm pvc insulated, unsheathedcable frls h, 1100 volt grade isi marked with multi stranded copper conductor along with 2.50 sqmm pvc insulated , unsheathed cable green colour frls h, 1100 volt grade isi marked with multi stranded copperwire as earth continuity conductor connected to common earth dolly complete all as specified and as directed by the engineer in charge. 130 description same all as per srl item no 125 here in before but for one socket outlet 15 amp with 4.00 sq mm pvc insulated, unsheathedcable frls h, 1100 volt grade isi marked with multi stranded copper conductor along with 4.00 sqmm pvc insulated , unsheathed cable green colour frls h, 1100 volt grade isi marked with multi stranded copperwire as earth continuity conductor connected to common earth dolly complete all as specified and as directed by the engineer in charge. 131 supply and fix modular switch 1 module, single pole, one way 6 amps flush type, 230 voltscomplete all as specified and as directedby engineer in charge. 132 supply and fix modular switch 1 module, single pole, one way 16 amps flush type, 230 voltscomplete all as specified and as directedby engineer in charge. 133 supply and fix modular switch 1 module, single pole, twoway 6 amps flush type, 230 voltscomplete all as specified and as directedby engineer in charge. 134 s&f modular bell push 6 amp, 1 way, 1 module, 230 volts complete all as specified and as directed by the engineer in charge. 135 supply& fixmodular socket outlet2 / 3 pin combined, 6 amp, one way, two module, 230 voltscomplete all as specified and as directedby engineer in charge. 136 supply& fixmodular socket outlet3 / 3 pin combined, ( 6pin ) , 6 / 16 amp, one way, two module, 230 voltscomplete all as specified and as directedby engineer in charge. 137 s&f electronic fan regulator modular 100 watt, 1 module, 230 volts , 50 hz, ac supply suitable for ceiling fan any type / make / sweep complete all as specified and as directed by the engineer in charge. 138 supply and fix ceiling rose surface type 2 / 3 terminalpolycarbonate, isolated body complete all as specified and as directed by the engineer in charge. 139 supply & fixcalling bell ding dong 230 volt including removing unserviceable bell, complete all as specified and as directed by the engr in charge. 140 s&f9 / 12 watt led light fitting wall mounting fixture ( sketch type ) including led lamp compact and energy efficient epoxy powder coated luminaire and connecting with copper conductor flexible cablefrom ceiling rose to connector of the light as in repair completeall as specified and as directed by the engineer in charge. 141 supply and fixing as in repairindoor decorative led tube light fitting box type 18 / 20 wattwith electronic driver, opal diffuser, high efficient pvc housing body suitable for led tube, high efficient, ac 220 240 volts, 50 hzincluding 18 / 20 watt led tube rod luminaries environment friendly, high efficient, t8 with aluminium extrusion heat sinkand connecting with copper conductor flexible cablefrom ceiling rose to connector of the lightcomplete all as specified and as directedby engineer in charge. 142 supply and fixingled surface mounted bulk head luminaries 8 10 watt with min 800 lumen, industrial model, ip 65, aluminium housing, surge protection including driver & led lampetc complete with all accessories, connecting with copper conductor flexible cablefrom ceiling rose to connector of the light as in repair complete all as specified and as directed by the engineer in charge. 143 s&f as in repair mirror light 9 / 12wattled wall mounting fixture, one feet , aluminium housing compact & energy efficient epoxy powder coated crca light luminaire, connecting with copper conductor flexible cablefrom ceiling rose to connector of the light complete all as specified and as directed by the engineer in charge. 144 s&fled bldg. security light fittings of capacity 20 25 watt made up of die castaluminiumhousing with black epoxy powder coating with cover heat resistance glass safety input voltage range 170 to 270 volts, industrial model with ip 65 protection and other connected accessories including electronic driver, service bracketof mild steelpipe 32 mm bore medium grade of length 0.9 mtr with ms clamps, bolts, nuts, and washers and suitable reducer for connecting fitting to ms pipe as required at site and two coats ofsynthetic enamel paintoverone coat of red oxide primer on mild steel work and making electrical connection, as in repair complete all as specified and as directed by the engineer in charge. 145 supply and fix mcb sp, 6 40 amps, 240 volt, 10 ka , b curve as per site requirement including removing old unserviceable mcb complete all as specified and as directed by the engineer in charge. 146 m & las in repair sub main wiring with two run of 6 sqmm pvc insulated , unsheathed cable frls h, 1100 volts grade isi marked with multi stranded copper conductor and one run of 6 sqmm pvc insulated , unsheathed cable frls h, 1100 volt grade isi markedmulti stranded copper conductor as earth continuity conductor connected to common earth dolly including concealed on wall / ceiling surfaces in pvc conduit medium gradeisi marked of adequate size for housing the wires complete all as specified and as directed by the engineer in charge.note: ( i ) thimble / lugs of rating of mcb should be used with wire for fixing in the mcb. ( ii ) three runs of cable and one run of pvc conduit shall be measured and paid as one unit length. 147 material & labourfor earthing complete with galvanised steel earth plate electrode 600x600x6 mm thick buried directly in ground ( earth pit not less than 2.25m deep below the ground level ) with top edge of the plate not less than 1.5mtr below the normal ground level connected to galvanised earthwire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron.earth wire protected by gi pipe 15mm bore ( medium grade ) and connected to earthing test pointas directed and as specified and shown in electrical plate no. 3 of ssr part i ( 2009 ) including necessary concrete pit in pcc ( 1:3:6 ) type c1, pre cast rcc ( 1:2:4 ) type b1 cover slab 40 cm x 40cm x 5cm reinforced with 8mm dia tmt bars @ 15cm c / cboth ways with one handle for liftingmade out of 8mm dia bar, funnel, wire mesh, 20mm dia gi pipe medium grade for watering, charcoal or coke and salt in alternate layers including necessary excavation and earth work in any type of soil and testingas in repair complete all as directed by engineer in charge and earth testing on completion . 148 material and labour cutting of existing walls in circular / square shape for making opening suitable for fixing 300 mm sweep exhaust fan and15 mm thick cement plaster on any faces of brick wallincement mortar 1:4, finishedeven and fair without using extra cement and applying two coats of white lime wash complete all as specified and as directed by the engineer in charge. 149 supply and fixingheavy duty exhaust fan 300mm sweep with corrosion resistant metallic body, minimum noise, operation and maintenance free design, totally enclosed, highly efficient, heavy duty motor with pressure die cast aluminium rotor mounted on two ball bearings, aerodynamically contoured blades, metallic base framewith rubbermountings for silent operation, maximum watt input not more than 55 watt, 1400 rpm, metal blades and shutter type louvers self openable / closeble for protecting the entrance of birds as per is :2132 1967 and testing complete all as specified and as directedby engineer in charge. 150 note: amount of credit ofrs. 72, 957.00 for retrieved materials is mentioned in schedule of credit page no. 47to 48 of tender documents in pdf form which will be deducted offline while acceptance of tender....

Military Engineer Services - Haryana

34996897 special repair of equipment shed no g 149, g 150, g 151 g 152 of 140 ad regt and provision of drainage from offrs mess bldg no p 144 to main drain in b area, allenby line of age br i under ge ( south ) ambala cantt material and labour for brick work with sub class ‘b’ bricks, straight or curved on plain exceeding 6 metre mean radius in cement mortar ( 1:6 ) including demolition of brick work built in cement mortar including demolition of old brick / stone masonry built in cement mortar of any description including all quoins, archs, pillars etc complete all as specified and directed. 2 material and labour for brick work ( except bricks ) straight or curved on plan exceeding 6 metre mean radius built in cm 1:6 ( old size brick ) including demolition of old brick masonry built in cement mortar of any description including all quoins, archs, pillars etc complete all as specified and directed. 3 taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed. 4 material and labour for rendering 15 mm thick on any faces of old brick work in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed. 5 material and labour for rendering 15 mm thick on fair faces of new brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and directed. 6 material andlabour for preparation of exposed brick wall surface by cleaning the surface wire brush to remove all dirt / loose materials from the bricks and from the joints between the bricks. prepared surface should be then washed with diluted hcl acid ( dilution ratio of 1:50 ) for three times in a day for two days. after acid wash surface should be allowed to be air dried for one day. note : further treatment over the surface so achieved will be carried out only after approved of the same by ge. 7 material and labour for carrying out efflorescence treatment to unplastered wall surface comprising of the following specifications and sequence with and including 15 mm thick rendering in cm 1:4 finished even and smooth without using extra cement : ( a ) prime the prepared surface with one of the following product mixed with cement in 1:1 ratio as bonding agent : ( i ) pidicrete urp of m / s pidilite. ( ii ) sika latex of m / s sika. ( iii ) nitobond sbr latex of m / s fosroc. ( b ) immediately after priming the surface pmm ( polymer modified mortar ) to be applied “by hand” while the prime is tacky. pmm should be prepared by mixing one of the following compounds in cement mortar 1:3 as per manufacturer’s instructions: ( i ) pidicrete urp of m / s pidilite. ( ii ) sika latex of m / s sika. ( iii ) nitobond sbr latex of m / s fosroc. ( c ) pmm surface should be allowed to dry for one day. after that it should painted with two coats of one of the following compound mixed with cement only in ratio of 1 ( selected compound ) : 1:5 ( cement ) : ( i ) pidicrete urp of m / s pidilite. ( ii ) sika latex of m / s sika. ( iii ) nitobond sbr latex of m / s fosroc. ( d ) now apply two coats of one of the following compound over the surface. these compounds are to be used as per manufacturer’s instructions: ( i ) pidifin 2k of m / s pidilite. ( ii ) brush coat of m / s sika. ( iii ) brush bond of m / s fosroc.note : both coats should be perpendicular to each other and gap between two coats shall be minimum 6 hours. ( e ) sprinkle loose coarse sand after second coat while surface is tacky.note: ( i ) the item will be executed by authorized applicator only of the selected / approved company. contractor shall submit details of authorised applicator for approval of ge before commencement of work in respect of above item. ( ii ) every stage of work will be approved by ge, then only next layer will be executed by contractor. 8 material and labour for rough cast plaster with and including 15mm thick rendering in cm 1:3 on brick wall or concrete surface as specified in clause 14.22 of ssr part i complete all as specified and directed.note: ( i ) after applying the under coat of cement and sand mortar 1:3 not less than 10 mm thick andwhile it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravelaggregate ( which is generally of size between 6 to 12 mm depending on the texture required ) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even. ( ii ) the mix of cement and sand shall be made slightly wetter than normal for rendering to ensurethat larger aggregates are thoroughly covered 9 material and labour for preparation of new plastered surfaces of walls and applying three coats of white wash on wall, complete all as specified and directed. 10 material and labour for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of alkali resistant primeron walls complete all as specified and directed. 11 material andlabour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper with hand roller, over a coat of alkaline resistant primer over a coat of wall care puttynot less than 1mm thick as per manufacturers instruction complete all as specified and directed. 12 material andlabour for preparation of old plastered surfaces of walls and applying two coats of white wash complete all as specified and directed. 13 material and labour preparation of old plastered surfaces of walls and applying one coat of cement base paint complete all as specified and directed. 14 supply andfixing of pre painted galvalume aluminium zinc coating gi based corrugatedsteel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa tensile strength as in roof covering / cladding to wall, fixed with self tapping screws or j type hooks including rubber washer etc complete including dismantling asbestos cement corrugated or semi corrugated sheets etc; complete all as specified and as directed. 15 supply andfixing of pre painted galvalume aluminium zinc coating gi based galvanised plain mild steel sheeting 0.50 mm thick of any colour, having 550 mpa tensile strength as in roof covering / ridges and fixed with self tapping screws or j type hooks including rubber washer etc complete including dismantling asbestos cement corrugated or semi corrugated sheets etc; complete all as specified and as directed. 16 dismantling timber scantling 40 sq. cm and over in section, in any position of unframed / framed work complete all as specified and directed. 17 material and labour for preparation of old painted steel surfaces of any description not otherwise described, over 10 cm in width or girth and applying one coat of synthetic enamel paint with approved shade complete all as specified and directed. 18 material and labour for taking down of rolled mild steel roof trusses ( framed ) of clear span above 08.00 metre and upto 12.00 metre any type, taking in safe costudy and refixing the same with and including using new nut bolts, welding & distance pieces, cleats etc., after completion of truss connected repair work etc complete all as specified anddirected. note: any damage to the existing truss during dismantling or refixing etc, shall be made good by the contractor with the same specifications as per existing work, without any extra cost to the govt. 19 dismatling of mild steel beam, purlin of existing truss andrefixing the same ( using nut bolt, welding ) rolled mild steel plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases, splices, angle brackets, cleats & other connections gde fe410 0 or fe 310 o complete all as specified and as directed. 20 supply and fixing of rolled mild steel sections as in main & cross beams, hip & jack rafters; purlins where connected to common rafters & running rails & guides for sliding doors; fixed with angle cleats or other connecting plates gde fe410 0 or fe 310 o complete all as specified and as directed. 21 supply andfixing of rolled mild steel work in roof trusses ( framed ) , trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing ( beam, tee, angle, channel or flat sections ) including distance pieces, cleats etc., quality confirming tofe 410 w ( gde e 250 ) quality a, complete, all as specified and as directed. 22 supply andfixing of mild steel plates ( plain or chequered ) channels, square cut or notched ( ordinary and counter sunk ) forming holes, with riveted, bolted or welded attachment conforming to grade fe 410 ( gde 250 ) , complete all as specified and directed. 23 material and labour for steel screw bolts, machine made, dia of neck 11 to 15mm with hexagonal or square head one end and screwed the other or screwed both ends, each screwed end to be fitted with washer and one hexagonal or square nut exceeding 22.5 cm and not exceeding 30cm long, complete all as specified and directed. 24 material and labour for two coats of synthetic enamel paint on steel surfaces over a coat of red oxide primerincludingpreparation of new steel surfaces of any description not otherwise described over 10 cm width or girth, complete all as specified and as directed. 25 material and labour for hardcore of gauge not exceeding 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. 26 material and labour for 150mm thick pcc 1:2:4 type b2 using 40mm graded mechanically crushed stone aggregate as in hardstanding / paths, finishing the concrete surface even and smoothwithout using extra cement including formingjoints and fillingwith mixture of bitumen and sand in ratio ( 1:1 ) by weight including necessary formwork etc and including demolition of existing old cement concrete in ground floors and pavings n.exc 15cm thickness ( below or above ) ground level complete all as specified and directed. 27 material and labour for 50mm thick pcc ( 1:3:6 ) type c 1 using 20mm graded mechanically crushedstone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10mm wide, 30mm deep joints at the rate of 3.00 mtr centre to centre and at every turning & filling the joints with bitumen & sand mixture including demolition of cement concrete in ground floor and pavings not exceeding 15 cm below or above ground level etc complete all as specified and directed. 28 surface excavation not exceeding 30 cm deep, averaging 15 cm deep and getting out in soft / loose soil, complete all as specified and directed. 29 material and labour for 100mm thick pcc ( 1:4:8 ) type d 2 using 40mm graded mechanically crushed stone as in sub base of floor / hard standing finished, complete all as specified and directed. 30 material and labour for providing and laying 80mm thick factory made chamfered edge cement concrete paver block of m 40 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size / shape, made by table vibratory method using pu mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed 31 material and labour for providing and laying of precast pcc solid concrete block, grade c confirming to is 2185 ( part i ) 2005 of 45 cm high, 10 cm thick and of suitable width including chamfers, weatherings, throating etc as in kerb continuous edging jointed in cement mortar 1:4 and struck flush pointing as the work proceeds and finishing with neat cement flush joint, complete all as specified and directed. 32 material andlabour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.11sqm but not exceeding 0.18 sqm, 7 to 8 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg / square metre and pointed in white or coloured cement to match the surface over and including15mm thick screed bed or layer in cement mortar ( 1:4 ) including dismantling of existing tiles etc including cement mortar bedding ( but not backing ) andrubbish off the premises complete all as specified and directed. 33 material and labour forpremium quality coloured glazed ceramic tiles ( 300x 450x 7mmthick ) in vertical surfacesand jointed in neat cement slurry @ 3.00 kg / square metre and pointed in white or coloured cement to match including rendering 10mm thick in cement plaster 1:3 including dismantling of old floor or wall tiling including cement mortar bedding and removing the rubbish outsidethe defence land complete all as specified and as directed. 34 material and labour for machine cut kota stone slab 20 25 mm thick ( size of each stone not less than 55cm x 55cm ) , laid in flooring, over and including cement screed bed 20mm thick in cement mortar ( 1:4 ) base set and jointed in neat cement slurry @ 3.00 kg / sqm and pointed in white or coloured cement to match the surface mixed with pigment to match shade of the slab over and including 25 mm thick cement concrete type b 0, 1:2:4 ( 12.5 mm graded aggregate ) as in levelling course, including cutting, waste, rubbing and polishing ( mirror finish ) including dismantling of existing stone slab / tiles etc including pcc and cement mortar bedding andrubbish off the premises complete all as specified and directed. 35 material and labour for machine cut kota stone slab 18 20 mm thick ( size of each stone not less than 55cm x 55cm ) , laid on vertical surfaces of skirting / dado, over and including cement screed bed 15 mm thick in cement mortar ( 1:3 ) and set and jointed in neat cement slurry @ 3.00 kg / sqm and pointed in white or coloured cement to match the surface mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing ( mirror finish ) including dismantling of existing stone slab / tiles etc including cement mortar bedding ( but not backing ) andrubbish off the premises complete all as specified and directed. 36 supply and fixing in repair of 5.5mm thick looking mirror of selected quality, beveled edge 450mmx600mm glass mounted on 6mm thick ac building board with aluminiumbeading andrubber packing and fixed to wall with wooden plug with chromium plated brass screw and cup washer complete all as specified and directed. 37 supply & fixing ( in repair ) vitreous china wash down water closet pedestal pattern ( ewc ) , white including connection to trap and to flushing pipe with ‘p’ or ‘s’ trap, making good to floor, plastic water closet seat cover with mild steel chromium plated hinges and chromium plated jet spray with 1.5 meter flexible ldpe pipe jointed with pipe complete all as specified and directed. 38 supply and fixing in repair of health faucet with 8mm dia, 1metre long flexible tube and wall hook complete all as specified and directed. 39 supply & fixing in repair of vitreous china wash hand basin white flat back of size 550x440mm including ci brackets and 15mm chromium plated pillar tap, pvc connection 450 mm long having ptmt nuts and 32 mm dia brass chromium plated waste coupling and making good to disturbed portion including32 mm dia pvc waste pipe etc., complete all as specified and directed. 40 supply and fixing in repair of 10 litre capacity virgin polypropylene cistern, white, isi marked, coloured at low level complete including supply and fixing45 cm pvc connection, pvc bend / flush pipe andmaking all connection , and removal old complete all as specified and directed. 41 supply and fixingin repair of vitreous china half stall urinal complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, pvc waste pipe, flush pipe, cp waste fitting, grating and union for discharge pipe complete all as specified and directed. 42 supply and fixing in repair of cp bib tap screwed down high pressure, long body, cast copper alloy, chromium plated with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified. ( note : weight of bib tap shall not be less than 0.575 kg ) 43 supply and fixing of gi tubing, isi marked, 15mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors including necassary cutting / chasing / pinning in wall and making good the disturbed surfaces as per existing whereever required, including taking down of old tubing as existing at site and removal, complete all as specified and as directed. 44 supply and fixing of gi tubing, isi marked, 20mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors including necassary cutting / chasing / pinning in wall and making good the disturbed surfaces as per existing whereever required, including taking down of old tubing as existing at site and removal, complete all as specified and as directed. 45 refixing old serviceable steel water tubing of 15 mm bore, in new or old position, any grade, including s&f new fittings as required, fixed to walls and ceilings or laying in floors including necassary cutting / chasing / pinning in wall and making good the disturbed surfaces as per existing whereever required , including taking down of old tubing as existing at site and removal, complete all as specified and as directed 46 refixing old serviceable steel water tubing of 20 mm bore, in new or old position, any grade, including s&f new fittings as required, fixed to walls and ceilings or laying in floors including necassary cutting / chasing / pinning in wall and making good the disturbed surfaces as per existing whereever required , including taking down of old tubing as existing at site and removal, complete all as specified and as directed 47 supply and fixing in repairs, water storage tank of 500 ltr capacity, hdpe double layer, isi marked, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, isi marked, screwed andsuitable for iron pipe 20 mm bore complete all as specified and directed. note: make of tank shall be engraved on the tank. 48 supply andfixing in repair of angle valve, 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with capstain head, heavy with adjustable wall flange, and removal old complete all as specified and directed. 49 supply & fixed in repair of stop cock, fancy type, chromium plated, long shank and cup ( concealed type ) screwed down high pressure with crutch or butterfly handle screwed both ends suitable for 15mm bore pipe, complete all as specified and directed. ( note : weight of stop cock shall not be less than 0.575 kg ) 50 supply and fixingin repair of chromium plated shower rose with swivel joints and including fixed to gi tubing 15mm bore size of shower not less than 125mm complete all as specified and directed. 51 supply and fixing in repair of chromium plated soap dish with fitting fixed with brass screws complete all as specified and directed. 52 supply and fixing in repair of 20 mm dia gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed. 53 supply andfixing in repair of brass chromium plated tubular towel rail, 20 mm dia, ‘d’ type 60 cm long between flanges complete all as specified and directed. 54 excavating in trenches, not exceeding 1.50 m wide & not exceeding1.5m depth & getting out in hard / dense soil complete all as specified and directed. 55 supply and fixing of pvc ( swr ) 75 mm pipe single socket in any length with rubber ring joints laid in floor or trenches includingdismantling ofpipes of any description any length etc complete all as specified and as directed. 56 supply and fixing of pvc ( swr ) 110 mm pipe single socket in any length with rubber ring joints laid in floor or trenches includingdismantling ofpipes of any description any length etc complete all as specified and as directed. 57 supply and fixing of pvc ( swr ) 110 mm pipe single socket in any length with rubber ring joints fixed to wall with ms clamps including dismantling ofpipes of any description any length etc complete all as specified and as directed. 58 supply and fixingin repair of 110 mm bore pvc ( swr ) bend with access door including jointing with solvent cement, complete all as specified and directed. 59 supply and fixingin repair of pvc ( swr ) 110 mm to 75 mm dia, reducers complete all as specified and directed. 60 supply and fixing in repair of 110 mm bore pvc ( swr ) , junction single t ( equal or unequal ) , including jointing with solvent cement, complete all as specified and directed. 61 supply and fixing in repair of pvc ( swr ) floor trap 75mm dia plain with pvc grating including jointing with solvent cement complete all as specified and directed. 62 taking down chowkats or frames with shutter, areanot exceeding 1.50 square metre ( w / o taking off shutters from frames ) and removing from site, including cutting holes in wall / concrete for taking out existing hold fasts and making good the disturbed portion of jambs andadjoining surfacesin cm ( 1:3 ) and finishing the surfaces to match with existing finish complete all as specified and directed. 63 taking down chowkats or frames with shutter, areaexceeding 1.50 square metrebut not exceeding 4 square metre ( w / o taking off shutters from frames ) and removing from site, including cutting holes in wall / concrete for taking out existing hold fasts and making good the disturbed portion of jambs andadjoining surfacesin cm ( 1:3 ) and finishing the surfaces to match with existing finish complete all as specified and directed. 64 supply and fixing of pressed steel frames for doors of size 125 x 60mm, 1mm thick, with one or more rebates including, hold fasts of 25mm x 4mm fi, 25cm long, 6 nos in each chowkhat, necessary lugs, 3 nos 100 mm ms butt hinges medium weight, cold rolled, welded for each shutters of frame, lock strike plate, including sanding, tarring backs of chowkhats, pcc 1:3:6 type c 0filling in frame and for holdfast, 2 nos 12 mm dia ms tie bars at the bottom of frame and one shop coat of red oxide primer etc complete all as specified and as directed. 65 supplyand fixing of factory made 35 mm thick, second class hard wood rail and style, plain framed, panelled shutter ( two panel ) with lock rail and panel of 9 mm b.w.p commercial ply or 12 mm veneered particle board with commrcial veneering on both faces ace, size of rails and stiles asper is 1003 ( part i ) kiln seasoned and chemical pressure treated complete all as specified and directed. 66 supply and fixing of iind class ( hollock ) factory made 35mm thick glazed skelton door shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass / gauge etc. with sizes of members of shutters as specified in para 8.24 ( a ) of ssr 2009 ( part i ) , complete all as specified and directed. 67 supply and fixing factory of made pvc hollow door frame of size 50mm x 47mm with wall thickness of 5 mm made out of extended 5 mm rigid pvc foam sheet cut at corner and jointed with 02 nos, 150 mm long brackets of size 15 mm x 15 mm mild steel square tubes 19 gauge including vertical door profiles reinforced with 19 mm x 19 mm steel square tube of 19 gauge ( epdm ) rubber gasket weather seal provided through out the frame and fixed to wall with 65 / 100 mm long mild steel screws through the frame by using pvc fasteners ( minimum of 04 nos of screws to be provided for each vertical numbers & minimum 02 nos for horizontal member ) complete all as specified and directed. 68 supply andfixing factory made solid pvc moulded door shutter, 28 to 30 mm thick ( stiles ) with 2, 4 or 6 raised panel design with 2 mm thick moulded pvc sheet on the front face & 2 mm plain colour pvc sheet on back face includingfixing in frame at site with 03 nos ss hinges, 02 nos aluminium tower bolt 150 mm, 02 nos aluminium handle 150 mm for each shutter all as per specification & drawing complete all as specified and directed. 69 supply and fixing in repair of steel window box type using erw hollow p section comprising double frame for and including gauged and glazed skelton shutter 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs etc. all as shown on drawing no. td 219 ( c ) sheet 1 / 3 to 3 / 3 and td 220 ( c ) sheet 1 / 3 to 3 / 3 as applicable including pcc ( c o , 1:3:6 using 12.5 graded agg ) bed blocks for hold fasts and one shop coat of red oxide primer etc complete all as specified and directed.note: ( i ) for the purpose of measurement & payment double shutter with frame shall be considered as one unit. ( ii ) unit rate quoted against this item shall also include the iron mongery , grills 10mm square bars. ( iii ) only glazing, wire mesh & painting grill shall be measured & paid for separately ) 70 supply and fixingin repairs of mild steel ventilator of section framed fixed type and fixed wire mesh with flat bends 10 mm x 3 mm with nuts / bolts complete including fixing lugs, necessary pcc 1:3:6 type c 1 for filling bed blocks of hold fasts / lugs, etc complete all as specified and directed. 71 supply and fixing of mild steel pressed handle, 150mm long, oval type, stove enameled black, complete all as specified and directed. 72 supply and fixing of mild steel barrel tower bolt stove enamelled black with bright bolt 200mm long complete all as specified and directed. 73 supply and fixing of250 mm long mild steel sliding door bolts , plate type, stove enamelled black, with bright bolt not less than 12mm with and including a minimum of 6 bolts and nuts , four on bolt plate and two on staple plate complete all as specified and directed. 74 returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in soil complete all as specified and directed. 75 removing surplus excavated material ( soil ) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed. 76 material and labour for pcc 1:3:6 type c 2 using 40mm graded mechanically crushed stone aggregate as in foundation filling, mass concrete, sub base etc. complete all as specified and directed 77 material and labour for plain cement concrete 1:2:4 type b 1 ( using 20mm graded mechanically crushed stone aggregate ) as in surface channels and drains, complete all as specified and as directed. 78 material and labour for pcc 1:2:4 type b 1 ( using 20 mm graded mechanically crushed stone aggregate ) ascopings, bed plates, kerbs, and other bands and the like, finished the surface fair andeven, including necessary form work etc including demolition of existing cement concrete of any description and in any position complete all as specified and directed. 79 material and labour for providing and laying of precast cement concrete solid concrete block, type b 1, 1:2:4 ( using 20mm graded stone aggreagate ) confirming to is 2185 ( part i ) 2005 of 30 cm high, 10 cm thick and of suitable width including chamfers, weatherings, throating etc as in kerb continuous edging jointed in cement mortar 1:4 and struck flush pointing as the work proceeds and finishing with neat cement flush joint etc complete all as specified and directed. 80 dismantling / taking down carefully aluminium / copper point wiring ( light, fan, socket or power ) complete, including fixtures and fittings such as switches, ceiling roses, pendants, regulators , sockets, light fittings etc., removing materials to stores for keeping in safe custody for taking credit and making good the disturbed surfaces of wall, floors, ceiling etc to match with the existing surfaces with matching obd / white wash / distemper complete all as specified and as directed. 81 material and labour for concealed point wiring with 1.50 sqmm single core pvc insulated, unsheathed cable frlsh, 1100 volt grade with multi stranded copper conductor drawn through and including medium grade, isi marked, pvc conduit not less than 25 mm dia with frlsh accessories, concealed and including provision of 1.50 sqmm single core pvc insulated, unsheathed cable frlsh 1100 volt grade with multi stranded copper conductorgreen colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to is 5139 ( pt i ) of 1969 and is:14772 2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer bothinternally and externally including provision of new 3 mm thick plastic laminated sheet top cover extended up to 25 mm over sunken box for housing the switches , socket outlets, fan regulators etc. with brass screws and brass washersand making goodthe disturbed surfaces as per existing for one light / fan point / bell point controlled by one switch complete all as specified and directed. notes : ( i ) the quoted rates shall be deemed to be inclusive for cutting chases by chase cutter in wall / pillars / columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. the portion of point wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using necessary accessories / fittings. ( ii ) point wiring & earth wire shall be connected to each & every flush / sunken box. ( iii ) all screws, fasteners, bolts, nuts & washer shall be cadmium plated & the cost of which is deemed to be included in the quoted unit rates. 82 description all as per item no 81.00 above but for socket out let point 5 amps on same board complete all as specified and directed. 83 description all as per item no 81.00 above but for socket out let point 5 amps on independentboard complete all as specified and directed. 84 description all as per srl item no 81.00 above but point wiring for one socket out let 15&5 amps ( independent ) controlled by one switchwith using 2.5 sq mm ( nominal area ) stranded copper conductor complete all as specified and directed. 85 supply and fixing of switch piano 6 amps, flush type, single pole, one way, 230 volt , ac supply, isi marked, complete all as specified and directed. 86 supply and fixing of switch piano 15 amps flush type one way 230 volts, 50 hz, ac supply, isi marked, complete all as specified and directed. 87 supply and fixingsocket outlet 3 pin 5 amps, 230 volts flush type , isi marked, complete all as specified and directed. 88 supply and fixing of socket outlet 2 in 1, 6 / 16 amps, 5 pin 230 volt flush type, isi marked complete all as specified and directed. 89 supply and fixing of ceiling rose surface bakelite 65x50mm, 3 terminal complete all as specified and directed. 90 supply and fixing offan regulator electronic step type , 230 volts, ac supply, suitable for ceiling fan any type / make / sweep, complete all as specified and directed. 91 supply and fixing lamp holder, pvc / polycarbonate type with back plate suitable for batten fittings, complete all as specified. 92 supply and fixing of led lamp 9 watt suitable for batten holder complete all as specified and directed 93 supply and fixing of double stiff pendants, comprising of galvanised steel or chromium plated brass bell mouth connectors 2 nos. with back plate and 2×1.50 metre long parallel 20mm dia galvanised or stove enamelled screwed steel conduit with two check nuts for fixing tube light fitting and upto 1.5 metre long twin core 0.5 sq. mm copper conductor flexible wire / cable including disconnecting and taking down old existing light fitting of any description and in any position complete all as specified and directed. 94 supply and fixing of industrial box channel for fixing of led tube rod, in crca body suitable for 2x18 / 20 watt led tube, high efficient, ac 220 240 volts, 50 hz and connecting with copper conductor flexible cable of size 0.50 sqmm from ceiling rose to connector of the light including disconnecting and taking down old existing light fitting of any description and in any position complete all as specified and directed. note : ( i ) tube rod shall be measured and paid for separately. ( ii ) channel must be get approved from engr in charge to check fesibilty i.e. one end contact or two end contact. 95 supply and fixing of channel for fixing of led tube rod, in crca body suitable for 18 / 20 watt led tube, high efficient, ac 220 240 volts, 50 hz and connecting with copper conductor flexible cable of size 0.50 sqmm from ceiling rose to connector of the light including disconnecting and taking down old existing light fitting of any description and in any position complete all as specified and directed. note : ( i ) tube rod shall be measured and paid for separately. ( ii ) channel must be get approved from engr in charge to check fesibilty i.e. one end contact or two end contact. 96 supply and fixing of 18 w / 20w polycarbonate led tube light, environment friendly, high efficient, t8 with aluminium extrusion heat sink for optimum performance with high luminous efficiency and easy and taking down existing tube light and removal complete all as specified and directed. note: tube rod must be get approved from engineer in charge to check fesibilty i.e. one end contact or two end contact for fixing in existing led fittings. 97 supply and fixing ofbulk head light fitting, 15 watt, energy efficient withlamp 15 watt with provision of 2 / 3 core pvc copper conductor cable 0.5 sqmm size from ceiling rose to light fitting completeincluding disconnecting and taking down old existing light fitting of any description and in any position complete all as specified and directed. 98 supply and fixing in repair bracket for security light made up of 25mm dia, 0.9 metre long gi pipe, light grade, bent to required length, fixed to wall with two clamps made of 20 x 3 mm mild steel flat minimum 15cm long, 4 nos 8mm dia bolts with nuts complete all as specified and directed. 99 supply and fixing led security light luminaire 50 watt , pressure die cast aluminum housing, toughened heat resistant glass, ip65 protection, better optics for uniform distribution with multiplte leds not less than 2 w each and having optical grade polycarbonate lens with all accessories internally pre wired and including connecting up with two core 1.5 sq mmcopper conductor cable from connector to ceiling rose to connection of light including disconnecting and taking down oldunserviceable security light fitting of any description and in any position complete all as specified and directed. 100 supply and fixing led high efficient bay light 50 watt, die cast aluminum housing, toughened heat resistant glass, ip66 protection, better optics for uniform distribution with all accessories internally pre wired and including connecting up with two core 1.5 sq mmcopper conductor cable from connector to ceiling rose to connection of light including disconnecting and taking down oldunserviceable security light fitting of any description and in any position complete all as specified and directed. 101 supply and fixing of sheet metal enclosures vertical distribution board vtpn, ( mccb db ) 4 ways, double door, 415 volts with 200 amps rated bus bar ip 54 protection, with shrouded neutral bar and insulated bus bar and earth link, with and includingmccb 4 pole thermal release type, 100 amps, 16 kaas incomer and mcbsas out going complete with making suitable size of ms cabinet 2 mm thick dully grouted on the wall ( flush ) with opening arrangement including making connections with suitable size of lugs / thimbles / glands and making good the disturbed surface matching with existing surface including taking down existing unserviciable mccb / dbs including mcbs complete all as specified and directed. 102 supply, installation, testingofspn distibution board 8 way, double door , ip 43, as per is 8623including 200 amps fully insulated copper bus bar, insulated neutral bar, earth bar, door earthing, reversible doors, pan assembly for easy installation and also incoming and outgoing connections with suitable size of lugs / thimblesincluding taking down existing unserviciable mcb / dbs including mcbs complete all as specified and directed. 103 supply, installation, testingofspn distibution board 4 way, double door , ip 43, as per is 8623including 200 amps fully insulated copper bus bar, insulated neutral bar, earth bar, door earthing, reversible doors, pan assembly for easy installation and also incoming and outgoing connections with suitable size of lugs / thimblesincluding taking down existing unserviciable mcb / dbs including mcbs complete all as specified and directed. 104 supply and fixing of mcb single pole, 240 volts, 50hz , breaking capacity 10ka, b curve 6 to 32 amps, including connection with suitable size copper lugs complete all as specified and directed. 105 supply and fixing of mcb single pole, 240 volts, 50hz , breaking capacity 10ka, b curve 40 to 63 amps, including connection with suitable size copper lugs complete all as specified and directed. 106 supply and fixing of mcb single pole and neutral, 240 volts, 50hz , breaking capacity 10ka, b curve 40 to 63 amps, including connection with suitable size copper lugs complete all as specified and directed. 107 material and labour for concealed sub main wiring with two single core frlsh pvcinsulatedunsheathed copper conductor cable 2.5 sqmm drawnin and including rigid non metallic pvc medium grade 25 mm dia concealed conduit with accessories onwall or ceiling withone additional pvc insulated , strandedcopper conductor frlshof 2.5 sqmm, green colourfor earthcontinuity conductor including taking down old unserviceable sub main wiringand making good the disturbed surface complete all as specified and directed.note : 3 run of cable and 1 run ofconduit shall be measured as 1 unit. ( ii ) the quoted rates shall be deemed to be inclusive for cutting chasesin wall / pillars / columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. the portion of sub main wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using necessary aceessories / fittings. 108 material and labour for concealed sub main wiring with two single core frlsh pvcinsulatedunsheathed copper conductor cable 4.00 sqmm drawnin and including rigid non metallic pvc medium grade 25 mm dia concealed conduit with accessories onwall or ceiling withone additional pvc insulated , strandedcopper conductor frlshof 4.00 sqmm, green colourfor earthcontinuity conductor including taking down old unserviceable sub main wiringand making good the disturbed surface complete all as specified and directed.note : 3 run of cable and 1 run ofconduit shall be measured as 1 unit. ( ii ) the quoted rates shall be deemed to be inclusive for cutting chasesin wall / pillars / columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. the portion of sub main wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using necessary aceessories / fittings. 109 material and labour for concealed sub main wiring with two single core frlsh pvcinsulatedunsheathed copper conductor cable 6.00 sqmm drawnin and including rigid non metallic pvc medium grade 25 mm dia concealed conduit with accessories onwall or ceiling withone additional pvc insulated , strandedcopper conductor frlshof 6.00 sqmm, green colourfor earthcontinuity conductor including taking down old unserviceable sub main wiringand making good the disturbed surface complete all as specified and directed.note : 3 run of cable and 1 run ofconduit shall be measured as 1 unit. ( ii ) the quoted rates shall be deemed to be inclusive for cutting chasesin wall / pillars / columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. the portion of sub main wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using necessary aceessories / fittings. 110 taking out of unserviceable earthing and material and labour for earthing and material & labour for earthing with galvanised steel earth plate electrode 60cmx 60cm x 6.0 mm thick buried directly in ground vertically at a depth not less than 2.25metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, earth plate surrounded from all sides by 15cm thick packed layer ofcharcoal dust and common salt filling in alternate layers and electrode connections by usinggalvanised iron wire 4mmas earthing lead ( upto terminal point ) by means ofbolts, nuts, check nuts and washers made of galvanised iron and thimbles and protected by light grade 15 mm diagi pipe connected to main switch board or main control board and gi pipe medium grade 20mm bore for watering and including funnel , wire mesh, 50 mm thick precast rcc 1:2:4 type b1using 20 mm graded stone aggregate , reinforced with 8 mm dia dedormed / tmt bars 3 nos both way 12 mm dia round bar handle and pcc chamber pit with pcc ( 1:3:6 ) type c 2 using 40mm graded stone aggregate, including excavation and earth work in any type ofsoil , returning , filling in approved soil and disposal of surplus soil to a distance not exceeding 50m all as specified and shown in electrical plate no 3 ofssr 2009 ( part i ) complete all as specified and as directed. note : ( i ) earth lead wire and its protection pipe upto and including 7.50 mtr only from top of earth electrode are included under this item. ( ii ) on testing if the earth resistance is not obtained within permissible limit, earthing will be re done at no extra cost , till the desired earth resistance is obtained. ( iii ) any joint in earth lead from earth electrode to test point shall not be allowed / permitted. 111 supply, laying and testing of cable xlpe insulated, armoured heavy duty electric cable with standred aluminium conductor, 1100 volts grade, cross sectional area of size 25 sqmm 4 core including dismantling existing any type and any size cable complete all as specified and directed. 112 supply, laying and testing of cable xlpe insulated, armoured heavy duty electric cable with standred aluminium conductor, 1100 volts grade, cross sectional area of size 10 sqmm 2 core including dismantling existing any type and any size cable complete all as specified and directed. 113 supply and fixing in repair of gi protection pipe of 40mmdia light grade for cable protection including all fittings laid in trenches or fixed on pole, complete all as specified and as directed. 114 material and labour for supply and filling sand with clean dry fine sand unwashed including gently punning around cables in trenches for cable protection complete all as specified and directed. note: punned thickness shall be measurement & paid. 115 material and labour for brick protection covers over cable using sub class b old size brick laid along length of cable complete all as specified and directed. 116 supply and fixing 1100 volts grade heavy duty cable pvc insulated aluminium conductor, served with inner sheathing of pvc tape and overall pvc sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular of size 16sqmm including all incoming and outgoing connection with proper size of thimble including disconnecting and taking down existing cables etc. complete all as directed and specified. 117 supply and fixing in repair of house service bracket ( hook type ) complete with 3.0 m long gi pipe 40mm dia medium grade pipe, two 90 degree bends. ms hook, stay or guy including fixing clamps etc complete all as specified and directed. 118 note: amount of credit ofrs. 74, 062.00 for retrieved materials is mentioned in schedule of credit page no 19 & 20 of tender documents in pdf form which will be deducted offline while acceptance of tender....

Military Engineer Services - Haryana

34977589 repair / maintenance of central air conditioning plant including misc items in zone a, zone b and zone c at af stn ambala under ge ( af ) ambala repair / maint of central air conditioning plant including misc items in zone a, zone b and zone c at af stn ambala under ge ( af ) ambala preventive, comprehensive & periodical maintenance / breakdown maintenance ofwater cooled scroll chiller plant of capacity 3x52tr / 3x50tr, checking servicibility of theparts of microprocessor based control panel such as microcontroller cards, sensors, relays, contactor, switches etc., compressor oil checking, checking of leakage of refrigerant piping etc. and descaling of condensor with suitable descaling chemical complete all as specified & directed. location: darin ii & nglgk make: blue star, model no: xwc4s 052ar2 2 preventive, comprehensive & periodical maintenance / breakdown maintenance of water cooled scroll chiller plant of capacity 3x37.7tr, checking servicibility of the parts of microprocessor based control panel such as microcontroller cards, sensors, relays, contactor, switches etc., compressor oil checking, checking of leakage of refrigerant piping etc.and descaling of condensor with suitable descaling chemical complete all as specified & directed. location: atcmake: blue star, model no: xwc3s 039ar2 3 preventive, comprehensive & periodical maintenance / breakdown maintenance ofwater cooled scroll chiller plant of capacity 3x25tr, checking servicibility of theparts of microprocessor based control panel such as microcontroller cards, sensors, relays, contactor, switches etc., compressor oil checking, checking of leakage of refrigerant piping etc. and descaling of condensor with suitable descaling chemical complete all as specified & directed. location: base ops, mcw, esc bay, storage iii & wsamake: blue star, model no: xwc2s 026ar2 4 preventive, comprehensive & periodical maintenance / breakdown maintenance ofwater cooled scroll chiller plant of capacity 3x25tr, checking servicibility of theparts of microprocessor based control panel such as microcontroller cards, sensors, relays, contactor, switches etc., compressor oil checking, checking of leakage of refrigerant piping etc. and descaling condensor with suitable descalingchemical complete all as specified & directed.location: second line service buildingmake: voltas, model no: wcuds 027dmn 5 preventive, comprehensive & periodical maintenance / breakdown maintenance ofwater cooled scroll chiller plant of capacity 3x12.5tr, checking servicibility of theparts of microprocessor based control panel such as microcontroller cards, sensors, relays, contactor, switches etc., compressor oil checking, checking of leakage of refrigerant piping etc. and descaling of condensor with suitable descalingchemical complete all as specified & directed.location: storage i & iimake: voltas, model no: wcuds 014dmn1x1 6 notes for boq item no. 1.00 to 5.00 here in before: ( i ) the descaling chemicalshould be non corrosive and non polluting in nature and safe to handle. descaling chemical compound is rxsol 41 8865 25. makes of desclaing chemical compound are scalebreak / vizag chemical / chemtex / west india chemical. ( ii ) the job includes all three units, condensers & cleaningand re assembling the complete plant after necessary maintenance and shall be measured as one job.. ( iii ) restarting and maintaining of the required / desired parameters should be provided by thecontractor. ( iv ) all the cleaning equipment i.e brush, cotton clothes, nuts, bolts of ciwashers etcas required of suitable sizesare included in quoted rates. ( v ) date wise record of stage passing register maintained when servicing of each unit of each plant alongwith consumable used in each unit to be maintained dully signed by contractor, je & engineer in charge. 7 preventive, comprehensive & periodical maintenance / breakdown maintenance ofair cooled scroll chiller plant of capacity 2x37.7tr, checking servicibility of theparts of microprocessor based control panel such as microcontroller cards, sensors, relays, contactor, switches etc., compressor oil checking, checking of leakage of refrigerant piping etc. and cleaning of condensor coil, servicing of condensor fan motor of chiller plant complete all as specified & directed. location: jaguar simulatormake: blue star model no. xac3s 036ma 8 preventive, comprehensive & periodical maintenance / breakdown maintenance ofair cooled scroll chiller plant of capacity 3x24tr, checking servicibility of theparts of microprocessor based control panel such as microcontroller cards, sensors, relays, contactor, switches etc., compressor oil checking, checking of leakage of refrigerant piping etc. and cleaning of condensor coil, servicing of condensor fan motor of chiller plant complete all as specified & directed. location: wwr storage iv & vmake: blue star model no. xac2s 024ma 9 notes for boq item no. 1.00 to 7.00 here in before: ( i ) the preventive, comprehensive & periodical maintenance / breakdown maintenance services shall be done through oem i.e. voltas or blue star. ( ii ) the contractor shall submit a mou signed by oem on stamp paper duly notarized, as per performa specified here in after alongwith a copy of annual maintenance contract from oem before commencement of work, failing which the contract will be liable to be cancelled and work shall be got executed at the risk & cost of the contractor. ( iii ) contractor will arrange oem visits for inspection and to check the functionality of the plants including maintenance services as required and shall provide state of chiller plant as & when and any no. of time as directed by engineer in charge. ( iv ) any breakdown intimated shall be attended within 48 hours failing which contractor shall be liable for a penalty of rs. 2000.00 for every 24hrs beyond initial 48hours. ( v ) the maintenance shall run for one year from the date of commencement of contract and during this period the smooth funcitoning of plant is responsibility of contractor. ( vi ) the job includes maintenance of all two / three units and re assembling the complete plant after necessary maintenance and shall be measured as one job. 10 notes for boq item no. 1.00 to 7.00 here in before ( contd... / ) : ( vii ) the maintenance of water / air cooled chiller plant at each location shall be considered as each job and payment shall be made accordingly. ( viii ) spare parts, compressor oil, refregerant shall be measured & paid seperetely. cost of minor part which are not catered here in after is deemed to be included in the quoted rates ( ix ) the rates quoted shall be deemed to be inclusive of the all above aspects. ( x ) the taking down of old unserviceable spare parts deemed to be included in quoted rates unless otherwise specifically not mentioned here in after. 11 m&l in replacement of existing micro processor based control panel of make blue star water cooled chiller plant model no: xwc2s 026ar2 with r 22 / 407c refrigerant basedscroll type of 25.1tr capacity complete in all respect with all electrical switchgear including undermentioned accessories complete all as specified & directed. ( i ) mcb c series, 50amp: 02 nos. ( ii ) motor protection device and single phase preventer vsp 3 : 02 nos. ( iii ) relay ( iv ) sensing transformer :02 nos. ( v ) contactor mnx50 :02 nos. ( make of contactor / switch gear : l&t, siemens, schneider ) ( vi ) current transformer100 amp / 05: 02 nos. ( vii ) printed circuit board ( pcb ) with display unit: 01 no.location: wwr building 12 m&l in replacement of existing micro processor based control panel of make blue star water cooled chiller plant model no: xwc4s 052ar2 with r 22 / 407c refrigerant basedscroll type of 50 / 52tr capacity complete in all respect with all electrical switchgear including undermentioned accessories complete all as specified & directed. ( i ) mcb c series, 50amp: 04 nos. ( ii ) motor protection device and single phase preventer vsp 3 : 04 nos. ( iii ) relay ( iv ) sensing transformer :04 nos. ( v ) contactor mnx50 :04 nos. ( make of contactor / switch gear : l&t, siemens, schneider ) ( vi ) current transformer 100 amp / 05: 04 nos. ( vii ) printed circuit board ( pcb ) with display unit: 01 no.location: nglgk 13 m&l in replacement of existing micro processor based control panel of make blue star water cooled chiller plant model no: xwc3s 039ar2 with r 22 / 407c refrigerant basedscroll type of 37.7tr capacity complete in all respect with all electrical switchgear including undermentioned accessories complete all as specified & directed. ( i ) mcb c series, 50amp: 03 nos. ( ii ) motor protection device and single phase preventer vsp 3 : 03 nos. ( iii ) relay ( iv ) sensing transformer :03 nos. ( v ) contactor mnx50 :03 nos. ( vi ) current transformer 100 amp / 05: 03 nos. ( vii ) printed circuit board ( pcb ) with display unit: 01 no.location: atc 14 notes for boq item no. 8.00 to 10.00: ( a ) the job includes replacement of complete internal and outer micorcontroller cards and display to achieve following conditions as undermentioned. micro processor based controller shall be as per following specification: ( i ) local mode: start / stop through touch screen. ( ii ) equalization of compressor runtime. ( iii ) micro processor control should ensure equal run time of compressor. ( iv ) safety and protection ( v ) motor protection device : protects chiller from ?phase unbalance ?phase loss ?phase reversal ?overload ?underload ( vi ) voltage protection device : protects chiller from ?phase loss ?phase reversal 15 notes for boq item no. 8.00 to 10.00 ( continued ) : ( vii ) additional safety features: protects system from ?freezing ?low pressure ? anti recycle ?low chilled water temperature?high pressure ?sensor error ?low water flow in condenser, ( b ) cost of replacement of field devices, chilled water inlet sensor and outlet sensor with their mounting and fixing accessories and high pressure and low pressurecut off switches of make : danfos / indfos deemed to be included in the quoted rate. ( c ) cost of the control panel wiring included in the quoted rate. 16 supply & installation of glycerin filled analogue pressure gauge with gauge cock, having following specification complete all as specified & directed: ( i ) pressure gauge; case & bazel ring : ss 304 ( ii ) snap action bayonet type ( iii ) bourdon & movement : ss 304 ( iv ) pressure element : ss 316 ( v ) ambient temp: 10°c ~ 45°c ( vi ) socket : ss 304 ( vii ) window : toughened glass ( viii ) mounting : bottom center ( ix ) accuracy class: 1.6 as per en 837 1. ( x ) nominal dia size: 100 mm. ( xi ) pointer: not adjustable, aluminum black. ( xii ) gauge cock: gauge cock should be in stainless steel with threaded connection suitable for nominal pressure of 16 bar. ( xiii ) connection size : 1 / 4 bsp. make : dwyer / forbes marshall / warrie / wika 17 supply & installation of thermometer, case and bezel moc shall be cast aluminum 304, weather proof as per ip 65. immersion length around 200 mm, connection 1 / 2 bsp with ss 304 thermowell dully filled with glycerin / equivalent complete all as specified & directed. 18 supply, installation, testing and commissioning of automatic purge valve, moc shall be of brass and plastic cap shall be provided on the outlet to shut the air vent when not in use. there shall be check valve at the bottom to seal the system when the auto air vent is removed for servicing. auto air vent shall be installed on all high points in the water piping system to automatically remove the trapped air. 3 / 8 bsp suitable for maximum operating pressure at 10 bar complete all as specified & directed. 19 s&f water flow switch of model hfs 25 complete all as specified & directed. 20 supply, installation, testing & commisioning of compressor scroll type, 380 to 400volt, 3 phase, 50 hz, thermally protected, lubricant mineral oil 160poe, refigerant type r 22 / 407c of capacity 12.5tr complete all as specified & directed.make: danfoss ( model no: sm185s4rc ) / daikin / copeland / emerson / carriernote: ( i ) the compressor should be installed by the authorisedcompanys refrigerant mechanic. ( ii ) after successful installation, the compressor should be vaccumed by the nitrogen at desired pressure and leakage should be checked. ( iii ) the rate offirst charge of refrigerant gas in the compressor deemed to be included in quoted rates. 21 s&f expansion valve with fixed orifice suitable for every type of refrigeration and air conditioning plants of existing makes and complete all as specified & directed. make: danfoss ( cat part no tgex 11 tr r22 / 407c ) 22 s&f liquid line filter drier / drier core filter as existing complete all as specified & directed.make: danfoss cat part no dcl 305 or equivalent model as recommended by the manufacturers. 23 s&f lwt / ewt ( leaving water temp and entering water temp ) sensors with probe as per the plant capacity alongwith minimum 6mtr of suitable core of copper cable as per existing size complete all as specified & directed. make: danfoss, invotec, abb, indfos. 24 s&f angle valves 1 / 4 x1 / 4complete all as specified & directed. 25 s&f crank case heater for scroll compressor ( 11 tr to 13.1 tr ) complete all as specified & directed. 26 s&f safety valvecomplete all as specified & directed. 27 s&f hrcfusewith holder, 20amp 40amps, 415volt complete all as specified & directed 28 supply & filling / top up of compressor oil, non freezing or as recommended by oem in ac plant including vaccum testing complete all as specified & directed. notes : ( i ) oil shall be brought by the contractor at site from authorised dealer / manufacturer company in sealed canes of standard packing with test certificate and purchase vouchers ( ii ) fillingshall be done in the presence of engineer in charge. 29 supply & charging of refrigerant gas r 407c in plant after detections / rectification of any leakages in the system using n2 gas and flushing the complete system thoroughly with nitrogen gas including pressure test complete all as specified & directed. 30 supply & charging of refrigerant gas r 410a in plant after detections / rectification of any leakages in the system using n2 gas and flushing the complete system thoroughly with nitrogen gas including pressure test complete all as specified & directed. 31 supply & charging of refrigerant gas r 22 in plant after detections / rectification of any leakages in the system using n2 gas and flushing the complete system thoroughly with nitrogen gas including pressure test complete all as specified & directed.notes for boq item no. 24.00 to 26.00 : ( a ) gas to be brought by the contractor at site from the authorised dealer / manufacturer and shall be in companys sealed cylinder and empty cylinders shall be returned to the contractor. ( b ) the unit rate quoted are inclusive of the cost of nitrogen / co2 gas used for leakage test and pressure test prior to filling / charging of gas. 32 supply only refrigerant gas r 22 in sealed cylinder complete all as specified & directed. 33 supply only refrigerant gas r 407c / 410a in sealed cylinder complete all as specified & directed. 34 supply only nitrogen gas in sealed cylinders of 10 kgs gas having pressure rating of 90psi of each cylinder for checking of leakage in all refrigerant piping and compressors complete all as specified & directed. notes for boq item no. 27.00 to 29.00 ( a ) gas to be brought by the contractor at mes store from the authorised dealer / manufacturer and shall be in companys sealed cylinder alongwith purchase vouchers. ( b ) empty cylinders shall be returnedto contractor aftercompletion of contract. 35 m&l periodical servicing of ahus capacity 6000 cfm to 10000 cfm by opening air filter, nut bolts, tray for ahu including cleaning of air filter panel, cleaning of cooling coil bycoil cleaner solution and high pressure water and rectified refrigerant leakage in cooling coilcomplete with brazing and soldering, opening and disconnectning ofahu motor fromblower room checkingseviceability fan, pulley, fan belt and oiling / greasing complete, replacement of unserviciable vibrating pads / springinside of ahufor equal air flow from blower to difuserofany type / capacity blower complete all as specified & directed. 36 m&l periodical servicing of ahus of capacity more than 12000cfm by opening air filter, nut bolts, tray for ahu including cleaning of air filter panel, cleaning of cooling coil bycoil cleaner solution and high pressure water and rectified refrigerant leakage in cooling coilcomplete with brazing and soldering, opening and disconnectning ofahu motor fromblower room checkingseviceabilityofshaft, fan, pulley, fan belt and oiling / greasing complete, replacement of unserviciable vibrating pads / springinside of ahufor equal air flow from blower to difuserofany type / capacity blower complete all as specified & directed. 37 m&l rewinding of ahus electric motor of capacity 15hp to 20hp three phase 415 volts by removing old unserceable burnt copper winding wire, cleaning of slots and insertion of insulating paper in the slots in appropriate size and rewinding with super enameled copper wire of suitable size alongwith insertion of superior quality of insulating material, winding, varnishing and drying, including dismantling of electric motors connections and refixing back after rewinding, replacement of connection plate and making necessary electric connection and testingcomplete all as specified & directed. 38 description all as per boq item no. 32.00 here in before but capacity 5hp to 10hp. 39 description all as per boq item no. 32.00 here in before but capacity 2hp to 3hp. 40 supply, installation, testing & commissioning in replacement 50mm dia electronic, self balancing, pressure independent type dynamic balancing valve with integrated modualating control valves in a single body. the actuator shall be capable of accepting upto 10volt dc and upto 20ma electric signal and shall provide similar transduced feedback output to control system. maximum close off pressure shall not be less than 6bar for upto 50mm valves and not be less than 7bar for 65mm & above. valves should have pressure rating of 25bar minimum. valve & actuator combination should be able to give logarithmic control characteristics to achieve linear control.the valve shall have manual override facility & the scope shall include proportionate thermostat, transformer as required and wiringfor interconnection with 1.5sqmm copper conductor multicore armoured cable complete all as specified & directed. make:honeywell, siemens, danfoss 41 s&f in replacement pre fine air filters panel of size 20 x 20 x 2inch for dust filtration of particles up to 5microns at 99% efficiency having air velocity through the filter approx 350 to 400 fpm complete all as specified & directed.make : zenith filters / afi / spectraco / asian filters 42 servicing of cooling towerof varying capacity 15tr to 50tr ac plant, dismantling of cooling tower for removing of top cover andreplacement of pvc frills and unserviceable nozzle, replacement of rusted nuts, bolts with washers etc and cleaning bottom tank to remove mud and dust complete all as specified & directed.note: spare parts i.e. float valve, pvc nozzels shall be measured & paid separately. 43 description all as per boq item no. 37.00 here in before but capacity more than 50tr. 44 m&l rewinding of electric fan motor of different cooling towers of capacity 2hp to 5hp, three phase 415 volts by removing old unserviceable burnt copper winding wire, cleaning of slots and insertion of insulating paper in the slots in appropriate size and rewinding with super enameled copper wire isi markedof suitable sizealongwith insertion of superior quality of insulating material, winding, varnishing and drying, including dismantling of electric motors connections and refixing back after rewinding including replacement of connection plate and making necessary electric connection and testingcomplete all as specified & directed. 45 s&f in replacement triple layer isi marked rotational molded polyethylene water storage tanks ( cylindrical vertical with closed top ) hoisted and fixed in position of capacity 5000 liters complete all as specified & directed. 46 s&f in repair galvanized wire mesh with wire of 1.40 mm dia, mesh size not less than 25 mm fixed on cooling tower by nut / bolts etc. complete all as specified & directed. 47 s&f in repair pvc float valve assembly 25 / 20mm complete all as specified & directed. 48 s&f in repair pvc nozzles as per existing complete all as specified & directed. 49 m&l water hydra / sprinkler for cooling tower of capacity 15tr to 50tr ac plant by dismantling of cooling tower electric motor and disconnecting all pvc nozzles from hydra and taking dwon & replacement of the same as per existing size / model hydra for suitable water flow by pvc nozzles withreplacement of rusted nuts, bolts with washers etccomplete all as specified & directed. 50 description all as per boq item no. 44.00 here in before but capacity more than 50tr. 51 s&f in replacement multi blade propeller fan of cooling tower having capacity of 15tr to 50tr . thefan blade construction moc should be aluminium alloy / frp as per existing at site complete all as specified & directed. note: sample shall be taken from site. 52 s&f in replacement drift eliminator of cooling tower having capacity of 50tr to 75tr as per existing at site complete all as specified & directed. 53 m&l in replacement of pvc fill blocks of size 600mm x 300mm x 150mm complete all as specified & directed. 54 s&f in replacement of air cooled condensor fan of size 660mm complete all as specified & directed. ac plant model no xac3s 036ma / xac2s 024mamake: delta 55 m&l in replacement ms pipe heavy grade of size 200mm bore with all fittings, welding, testings etc. laid in floors or fixed to walls and ceilings etc of sizes including providing two coats of anti corrosive paint over & including one coat of primers on external surfaces of pipes complete all as specified & directed. 56 description all as per boq item no. 50.00 here in before but size 150mm bore. 57 description all as per boq item no. 50.00 here in before but size 100mm bore. 58 description all as per boq item no. 50.00 here in before but size 80mm bore. 59 m&l in replacement gi pipe 50mm bore medium grade isi markedwith all fittings laid in floors or fixed to walls and ceilings etc complete all as specified & directed. 60 description all as per boq item no. 54.00 here in before but 40mm bore. 61 description all as per boq item no. 54.00 here in before but 25mm bore. 62 description all as per boq item no. 54.00 here in before but 20mm bore. 63 supply, fixing & testing in replacement butterfly valve ( manual ) size 150mm with ci body ss disc, insulated, nitrile rubber seal & o ring pn 16 pressure rating for chilled water / hot heater circulation complete all as specified & directed.make: castle, zoloto, sant, venus 64 description all as per boq item no. 58.00 here in before but size 100mm. 65 description all as per boq item no. 58.00 here in before but size 80mm. 66 description all as per boq item no. 58.00 here in before but size 50mm / 40mm. 67 s&f in replacement non return valve, size 150mm with dual plate of ci body ss plates vulcanized nbr seal flanged end & pn 16 pressure rating for chilled / hot water circulation including insulation complete all as specified & directed. make : audco, honeywell, intervalve, ksb, vtm 68 description all as per boq item no. 62.00 here in before but size 100mm. 69 description all as per boq item no. 62.00 here in before but size 80mm. 70 description all as per boq item no. 62.00 here in before but size 50mm / 40mm. 71 s&f in replacement y strainer size 150mm of ductile ci body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation complete all as specified & directed. 72 description all as per boq item no. 66.00 here in before but size 100mm. 73 s&f in replacement of gun metal gate valve isi marked including cutting / threading and welding to existing gi pipe of size 50mm dia complete all as specified & directed. 74 description all as per boq item no. 68.00 here in before but size 40mm dia. 75 description all as per boq item no. 68.00 here in before but size 25mm dia. 76 description all as per boq item no. 68.00 here in before but size 20mm dia. 77 m&l rewinding of condensor and chilled water electric motor of capacity 7.5hp to 12.5hp, three phase 415 volts by removing old unserviceable burnt copper winding wire, cleaning of slots and insertion of insulating paper in the slots in appropriate size and rewinding with super enameled copper wire isi markedof suitable sizealongwith insertion of superior quality of insulating material, winding, varnishing and drying, including dismantling of electric motors connections and refixing back after rewinding, replacement of connection plate and making necessary electric connection and testingcomplete all as specified & directed. 78 description all as per boq item no. 72.00 here in before but capacity 3hp to 5hp. 79 decoupling of monoblock pump from electric motor, dismantling from the foundation and shifting to local workshopfor repair / overhauling of monoblock pumping set capacity 7.5hp to 12.5hp ( condensor and chilled water pump ) taking out impeller bush bearing shaft stuffing box reassembling the same after replacing the defective parts & carrying out the necessary repair remetallingturning polishing the pump shaft replacement including replacement of steel studs and unserviceable nuts and bolts repair / replacement of ball bearing impellor stuffing box greasing etc and testing on completion and commisioning and installation at site complete all as specified & directed.notes: ( i ) the complete job includes making good the existing pumps water leakage proof. ( ii ) cost of the spare parts except gm bush, impeller, stuffing box and ball bearing shall deemed to be included in the quoted rate. 80 s&f bearing for 7.5hpto 12.5hp pumpsets complete all as specified & directed.make: skf / nbc 81 s&f bronze / gm impeller of pumpset of capacity 7.5hpto 12.5hp complete all as specified & directed. 82 s&f stuffing box alongwith pressure plate and hexa nuts studds etc required for gland packing and pump shaft as per existing make pumpset of capacity 7.5hpto 12.5hp complete all as specified & directed. 83 s&f gun metal bush of pumpset of capacity 7.5hp to 12.5hp complete all as specified & directed. 84 decoupling of monoblock pump from electric motor, dismantling from the foundation and shifting to local workshopfor repair / overhauling of monoblock pumping set capacity 3hp to 5hp ( condensor and chilled water pump ) taking out impeller bush bearing shaft stuffing box reassembling the same after replacing the defective parts & carrying out the necessary repair remetallingturning polishing the pump shaft replacement including replacement of steel studs and unserviceable nuts and bolts repair / replacement of ball bearing impellor stuffing box greasing etc and testing on completion and commisioning and installation at site complete all as specified & directed.notes: ( i ) the complete job includes making good the existing pumps water leakage proof. ( ii ) cost of the spare parts except gm bush, impeller, stuffing box and ball bearing shall deemed to be included in the quoted rate. 85 s&f bearing for 73hpto 5hp pumpsets complete all as specified & directed.make: skf / nbc 86 s&f bronze / gm impeller of pumpset of capacity 3hpto 5hp complete all as specified & directed. 87 s&f stuffing box alongwith pressure plate and hexa nuts studds etc required for gland packing and pump shaft as per existing make pumpset of capacity 3hpto 5hp complete all as specified & directed. 88 s&f gun metal bush of pumpset of capacity 3hp to 5hp complete all as specified & directed. 89 s&f in replacement gland packing for monoblock pumpset / centrifugal end suction pumpset of capacity 3hp to 15hp as per existing make complete all as specified & directed. 90 m&lattending day to day complaints pertainsto ac plant of any capacity as and when required with skilled refregeration mechanic / electrician & helper alongwith necessary t&pfor checking the equipment at existing location and find out the faults / defects and rectify the defects in situ and cleaning / normal maintenance to the equipments ( including lugs wire phase preventer, nuts, bolts etc as required on site ) complete to make the equipment functional in all respect complete all as specified & directed.note : ( i ) spare parts shall be measured and paid separately except minor items like thimbles / lugs wire etc. ( ii ) taking out / down & fixing of new spare parts included in quoted rates unless otherwise specifically not mentioned here in after. 91 supply only single phase preventer system of supply 415volt, 50hz model vsp2 of make minilec or equivalent of l&t / abb complete all as specified & directed 92 supply only auxiliary contactormnx a 2 for 415volt 10amps for contactor25amp complete all as specified & directed.make: l&t, havells, legrand 93 supply only contactor mnx 25 40 amp complete all as specified & directed make: l&t, havells, legrand 94 supply only contactor mnx 50 70 amp complete all as specified & directed make: l&t, havells, legrand 95 supply only contactor mnx 18 amp complete all as specified & directed make: l&t, havells, legrand 96 supply only side mounting add on block with aux contact 1no+1nc suitable for mnx 9 to 40amp contactor of complete all as specified & directed. make: l&t, havells, legrand 97 supply only electronic timers type et 100, 110 / 240 volt, 50 hz complete all as specified & directed. 98 supply only timer gt 200 complete with coilvoltage 220volt complete all as specified & directed.make: bch, l&t 99 supply only overload relay 6 to 10 amps, 3 pole, directly operated complete all as specified & directed.make: bch, l&t 100 supply only overload relay 9 to 14 amp 3 pole, directly operated complete all as specified & directed.make: bch, l&t 101 supply only overload relay 20 to 32 amp 3 pole, directly operated complete all as specified & directed.make: bch, l&t 102 supply only overload relay 28 to 42 amp 3 pole, directly operated complete all as specified & directed.make: bch, l&t 103 supply only selector switch 4 way for voltmeter complete all as specified & directed. 104 supply only toggle switch spst 10 amps complete all as specified & directed. make: kayceel, l&t 105 supply only voltmeter 0 500volt digital type, complete all as specified & directed.make: ae, crompton greaves 106 supply only ammeter0 100amps digital type, complete all as specified & directed.make: ae, crompton greaves 107 supply only mcb 25 amp to 63 amp triple pole complete all as specified & directed. 108 supply only mcb 16 amp to 32 amp, triple pole neutral complete all as specified & directed. 109 supply only mcb 40 amp to 100 amps, triple pole neutral complete all as specified & directed. 110 supply only mccb, adjustablethermal and adjustable magnetic setting of capacity 250amp, 415volt, four pole, 36 kacomplete all as specified & directed 111 supply only mccb, adjustablethermal and adjustable magnetic setting of capacity 200 amps, 415volt, four pole, 36 ka complete all as specified & directed 112 supply only mccb, adjustablethermal and adjustable magnetic setting of capacity 160 amps, 415volt, four pole, 36 ka complete all as specified & directed 113 supply only mccb, adjustablethermal and adjustable magnetic setting of capacity 125 amps, 415volt, four pole, 16 ka complete all as specified & directed 114 supply only mccb, adjustablethermal and adjustable magnetic setting of capacity 100 amps, 415volt, four pole, 16 ka complete all as specified & directed 115 supply only mpcb, thermal magnetic release and adjustable setting of capacity 9 to 13 amps, 415volt, three pole, 25 ka complete all as specified & directed 116 supply only mpcb, thermal magnetic release and adjustable setting of capacity 11 to 17 amps, 415volt, three pole, 20 ka complete all as specified & directed 117 m&l in replacement pvc insulated, armoured, shielded , multistranded copper conductor cable for instrumentation havingsignal capacity of ( 4 20 ) ma / 24vac / 24vdc of size 01 sqmm 4 core including saddles, & screws with laying in & including ms conduit light gradeperfectly complete all as specified & directed. 118 s&f in replacement ofcomplete set of heating element 220 / 380 volts or required for 63kilowatt hot water generator complete all as specified & directed.. 119 s&f in replacement of electric strip heaters3 kilowatt capacity isi marked complete all as specified & directed. 120 m&l in replacement to suction / discharge valve of teflon sheet ‘o’ ring etc complete all as specified & directed. 121 m&l in replacement for providing thermal insulation to supply air ducts / return air ducts with 32 mm thick , epdm rubber with factory laminated glass cloth 7mil, 200 gsm sheet, use adhesive fevicol sr 998, joint should be sealed withtape of at least2 wide ( standard type ) and finished withcoating of fevicol ac duct king lag coating af: 5590 and finally finish with uv resistance paint as per client choice complete all as specified & directed. 122 s&f in replacement pin up display board of wooden of size 2x3 feet alongwith 50 pins complete to pin up the fire safety orders, sop, standing orders for the ac plants complete all as specified & directed. 123 supply, installation, testing & commisioning ofpump suitable for 7.5hp electric motor, bronze / ss impeller, gm bushes, stuffing box and making all connection with existing condensor and chiller system complete with all accessories / pipe fittings including taking down of existing pump and making connections to starter complete all as specified & directed. 124 supply, installation, testing & commisioning of monoblock pump set of motors capacity 2 / 3 hp electric motor 3 phase 415 volt, ie3 and making all connection with existing condesor and chiller system complete with all accessories / pipe fittings includingtaking down of existing pump and making connections to starter complete all as specified & directed. 125 supply, installation, testing & commisioning of electric motor of capacity 7.5hp for prime mover of pumpset, 3 phase 415 volt, ie3 and making all connection with existing condesor and chiller system complete with all accessories / pipe fittings includingtaking down of existing electric motor and making connections to starter complete all as specified & directed. 126 description all as per boq item no. 120.00 here in before but capacity 5hp. 127 description all as per boq item no. 120.00 here in before but capacity 1 / 2hp. 128 s&f electrical insulating rubber mat of size ( 2mtr x 1mtr x 3mm ) tested for lt voltage 1100 volts complete all as specified & directed. 129 m&lfor spray painting to central ac plant completecomprisingof compressors, motors, condensor, cooling tower and cooling tower pumps, pump / monoblocks, ms / gi pipe lines of sizes etc after preparation of old painted surface as per colour code includingand marking arrow, sm / mes nos, colour for 11 to 100tr acs plantcomplete all as specified & directed. 130 s&f v belt of size a 50 / 54 / 65 / 81, b 47 / 56 / 59 / 70 / 72 / 75 / 76 / 78 / 80 / 82 / 90 / 94 / 101 / 102 / 103, c 107 complete all as specified & directed. 131 s&f in replacement outdoor fan of package type ac plant of capacity 17tr, suitable for plant of make bluestar, model no dpa2163r3 i. the moc of the fan blade shall be frp type complete all as specified & directed. 132 s&f in replacement outdoor fan of package type ac plant of capacity 11tr, suitable for plant of make bluestar, model no dpa1441r3 i. the moc of the fan blade shall be frp type complete all as specified & directed. 133 m&l for descaling and cleaning oftubes of condenser ( heat exchanger ) unit, tube of central ac plant including opening and refixing in original position all as required at site for shell and tube condensor unit of package type ac plant by using proper descaling solution by suitable size of drill rod, wire brush, cleaning by circulating pressure water by pressure pumps till the complete deposits / scale is removed as ordered, replacement of packing gasket, nuts, bolts with washer of both ends of condensor complete all as specified & directed. 134 s&f, testing & installation ofduct mounted temperature and rh transmitter with digital display complete all as specified & directed.. make: invotec / honeywell / danfoss. 135 m&l for writing sm / mes no. with suitable paint / color ( as approved ) on the ac ( window / split type ) , coolers / desert coolers, water coolers etc possessed by user complete all as specified & directed. note: contractor shall deploy his painter who will approach the user with the permission of department and shall write sm / mes no. and quoted rate deemed to be included the cost of visit of deployed painter to user. 136 s&f in replacement balancing valve of size 80mm with built in flow measuring facility with ci body flanged construction with epdm coated disc with long pitch with protected out pipe insulation & pn 16 pressure rating for chilled / hot water circulation complete all as specified & directed. 137 description all as per boq item no. 131.00 here in above but size 50mm. 138 for credit schedule, refer tender documents. the amount of credit schedule shall be deducted from total quoted amount of boq to arrive contract sum....

Northern Railway - Haryana

32872398 supply of (1)supply of anti corrosive paint for underframe of lhb coaches as per icf/md/spec 357 (2) application of anti corrosive paint for underframe of lhb coaches(1)supply of anti corrosive paint for underframe of lhb coaches as per icf/md/spec 357 (2) application of anti corrosive paint for underframe of lhb coaches,supply of anti corrosive paint for underframe of lhb coaches as per icf/md/spec 357 , application of anti corrosive paint for underframe of lhb coaches...

Northern Railway - Haryana

32860665 supply of (1) supply of anti corrosive painting of underframe of lhb coaches as per specification icf/md/spec 357. quantity required for per under frame is 12.5 gallon/50 ltrs. (2) application of anti corrosive paint for underframe of lhb coach(1) supply of anti corrosive painting of underframe of lhb coaches as per specification icf/md/spec 357. quantity required for per under frame is 12.5 gallon/50 ltrs. (2) application of anti corrosive paint for underframe of lhb coach,supply of anti corrosive painting of underframe of lhb coaches as per specification icf/md/spec 357. quantity required for per under frame is 12.5 gallon/50 ltrs. , application of anti corrosive paint for underframe of lhb coach...

Northern Railway - Haryana

32844380 supply of (1)supply of anti corrosive paint for underframe of lhb coaches as per icf/md/spec 357 (2) application of anti corrosive paint for underframe of lhb coaches(1)supply of anti corrosive paint for underframe of lhb coaches as per icf/md/spec 357 (2) application of anti corrosive paint for underframe of lhb coaches,supply of anti corrosive paint for underframe of lhb coaches as per icf/md/spec 357 , application of anti corrosive paint for underframe of lhb coaches...

Kendriya Vidyalaya Sangathan - Haryana

31979331 bids are invited for enamel paint , anti corrosive paint , emulsion paint matt , distemper , red oxide ochre , chuna for white wash , putty, chuna powder total quantity : 49160...

Northern Railway - Haryana

31951385 supply of supply application of anti corrosive paintingsupply application of anti corrosive painting,supply of anti corrosive paint for painting of 25 nos. underframe of lhb coaches as per specification icf/md/spec 357. quantity required per under frame is 50 ltrs. , application of anti corrosive paint for underframe of lhb coach...

Northern Railway - Haryana

31064655 supply of supply application of anti corrosive paintingsupply application of anti corrosive painting,supply of anti corrosive paint for painting of 25 nos. underframe of lhb coaches as per specification icf/md/spec 357. quantity required per under frame is 50 ltrs. , application of anti corrosive paint for underframe of lhb coach...

Northern Railway - Haryana

31064412 supply of supply application of anti corrosive paintingsupply application of anti corrosive painting,supply of anti corrosive paint for painting of 25 nos. underframe of lhb coaches as per specification icf/md/spec 357. quantity required per under frame is 50 ltrs. , application of anti corrosive paint for underframe of lhb coach...

Northern Railway - Haryana

31003356 supply of supply application of anti corrosive paintingsupply application of anti corrosive painting,supply of anti corrosive paint for painting of 25 nos. underframe of lhb coaches as per specification icf/md/spec 357. quantity required per under frame is 50 ltrs. , application of anti corrosive paint for underframe of lhb coach...

Northern Railway - Haryana

31003312 supply of supply application of anti corrosive paintingsupply application of anti corrosive painting,supply of anti corrosive paint for painting of 25 nos. underframe of lhb coaches as per specification icf/md/spec 357. quantity required per under frame is 50 ltrs. , application of anti corrosive paint for underframe of lhb coach...

Northern Railway - Haryana

30973596 supply of supply application of anti corrosive paintingsupply application of anti corrosive painting,supply of anti corrosive paint for painting of 25 nos. underframe of lhb coaches as per specification icf/md/spec 357. quantity required per under frame is 50 ltrs. , application of anti corrosive paint for underframe of lhb coach...

Northern Railway - Haryana

30059106 supply of supply and apply of anti corrosive paintingsupply and apply of anti corrosive painting,supply of anti corrosive painting as per specification icf/md/spec 357 on two lhb bogie set (4bogie frames and 4 bolsters). one set consists of 02 nos of lhb bogies. quantity required per set: 14 litres perset , application of anti corrosive painting on lhb bogies , supply of anti corrosive paint for two nos of underframe of lhb coach as per icf/md/spec 357 , application of anti corrosive paint for two nos of underframe of lhb coach...

Northern Railway - Haryana

30009232 supply of supply and apply of anti corrosive paintingsupply and apply of anti corrosive painting,supply of anti corrosive painting as per specification icf/md/spec 357 on two lhb bogie set (4bogie frames and 4 bolsters). one set consists of 02 nos of lhb bogies. quantity required per set: 14 litres perset , application of anti corrosive painting on lhb bogies , supply of anti corrosive paint for two nos of underframe of lhb coach as per icf/md/spec 357 , application of anti corrosive paint for two nos of underframe of lhb coach...

Northern Railway - Haryana

29878125 supply of supply and apply of anti corrosive paintingsupply and apply of anti corrosive painting,supply of anti corrosive painting as per specification icf/md/spec 357 on two lhb bogie set (4bogie frames and 4 bolsters). one set consists of 02 nos of lhb bogies. quantity required per set: 14 litres perset , application of anti corrosive painting on lhb bogies , supply of anti corrosive paint for two nos of underframe of lhb coach as per icf/md/spec 357 , application of anti corrosive paint for two nos of underframe of lhb coach...

Military Engineer Services - Haryana

25565877 repair of mt vehicle , m&l for removing the existing seats and cushioning alongwith seat covers from the vehicle and refixing properly including replacement of broken seat supports and accesories such as springs , rods , sheets , nuts , bolts etc for tata 207 ba no 11c 091819x complete all as specified and directed by engr in charge . , supply and fixing of new seat covers and cushioning as per existing and as approved for tata 207 ba no 11c 091819x complete all as directed by engineer in charge . note: seat covers will be as approved by engineer in charge . , supply and fixing of new floor blanket inside the complete cabin of vehicle & fixing and sticking alogwith clamping properly the blanket to the cabin floor as per existing and as approved for tata 207 ba no 11c 091819x complete all as directed by engineer in charge . , supply and fixing foot mats in the cabin of vehicle as per existing and as approved for tata 207 ba no 11c 091819x complete all as directed by engineer in charge . , m&l for replacement of cabin roof clothes and rexin suitable for tata 207 ba no . 11c 091819x complete all as specified and directed by engr in charge . note: clothes and rexin sample and colour will be decided by engr in charge . , m & l for complete servicing of vehicle including replacement of following parts as recommended by oem and testing on completion for tata 207 11c 091819x: , fuel filter 01 set , lub oil filter 01 no , air filter 01 no , engine oil make valvoline , rear oil , gear oil , grease , brake oil , coolent , clothes , m&l for opening the existing alternator from the vehicle for servicing and overhauling including replacement of carbon bushes , armature winding and bush bearing and re assembling & fixing to vehicle including testing complete suitable for tata 207 ba no . 11c 091819x complete all as specified and directed by engr in charge . note: make of parts shall be mico/lucas or equivalent as recommended by manufacturer . , m&l for opening the existing wiper blade with blade arm connected to blade and replacement of wiper blade with blade arm and testing on completion for tata 207 11c 091819x . make: bosch/trico or as recommended by oem complete all as specified and directed by engr in charge . , m&l for taking out front and rear wheels complete from vehicle , cleaning , polishing and overhauling of brake system ( of 02x02 nos of wheels ) by providing new wheel cylinder kit , brake shoe , brake liner , brake pipes complete ( make: tvs/bosch/tata genuine ) , cleaning & polishing of wheel drum , greasing of front and rear wheels bearing , taking out tyres , tubes of each wheels , cleaning of each wheels , disc and rims & applying two coats of anti corrosive paint after making smooth surface , re assembling of wheels and re fixing all parts & wheel alignment from authorised workshop complete with recommendations etc testing on completion for tata 207 11c 091819x complete all as as specified and directed by engr in charge . , m&l for supply & replacement of tail light assembly complete ( brake light , side indicator light and parking light with suitable wattage of lamps ) and testing on completion make kk/lucas/tata genuine complete all as specified and directed by engr in charge suitable for tata 207 11c 091819x . , m&l for opening the complete window with inner flap , locking , opening ( outer and inner ) arrangements , servicing and minor repair for opening and closing of window mirror including replacement of locking button , window opening handle from inner and outer side , window mirror up and down handle for tata 207 11c 091819x and re fitting all and testing on completion complete all as specified and directed by engr in charge . note: parts shall be as per sample approved by engr in charge . , m&l for opening the exising self starter from the vehicle for servicing and overhauling including replacement of worn out pinion , varnish of coil , replacement of solenoid switch , carbon bush , armature winding and re assembling with engine including testing complete suitable for tata 207 11c 091819x complete all as specified and directed by engr in charge . note: make of parts mico/lucas or equivalent as recommended by manufacturers . , m&l for taking out the existing un serviceable and detriorated wiring of tata 207 11c 091819x carefully including fuse box and ignition switch , replacement of complete vehicle wiring of headlight , deshboard light , cabin light , self starter and alternator etc as per standard manufacturer , replacement of fuse box minimum 8 nos of fuses with new fuses , ignition switch with key for tata 207 & testing on completion complete all as specified and directed by engr in charge . note: new complete wiring set as per existing size/make and colour coding . , m&l for taking down complete steering system from vehicle opening , dismentaling , taking out all parts , cleaning of serviceable parts and replacement of un serviceable parts ( steering column , tie rod , spindles , universal joints , pitman arm , steering gear box assembly , drag link assembly alongwith all connected parts etc . ) and re assembling and fixing to vehicle & testing on completion for tata 207 11c 091819x complete all as as specified and directed by engr in charge . make of un serviceable parts will be tata genuine/rane/zf . ...

Military Engineer Services - Haryana

25565789 repair of mt vehicle , m&l for removing the existing seats and cushioning alongwith seat covers from the vehicle and refixing properly including replacement of broken seat supports and accesories such as springs , rods , sheets , nuts , bolts etc for tata 207 ba no 98c 66591n complete all as specified and directed by engr in charge . , supply and fixing of new seat covers and cushioning as per existing and as approved for tata 207 ba no 98c 66591n complete all as directed by engineer in charge . note: seat covers will be as approved by engineer in charge . , supply and fixing of new floor blanket inside the complete cabin of vehicle & fixing and sticking alogwith clamping properly the blanket to the cabin floor as per existing and as approved for tata 207 ba no 98c 66591n complete all as directed by engineer in charge . , supply and fixing foot mats in the cabin of vehicle as per existing and as approved for tata 207 ba no 98c 66591n complete all as directed by engineer in charge . , m&l for replacement of cabin roof clothes and rexin suitable for tata 207 ba no . 98c 66591n complete all as specified and directed by engr in charge . note: clothes and rexin sample and colour will be decided by engr in charge . , m & l for complete servicing of vehicle including replacement of following parts as recommended by oem and testing on completion for tata 207 98c 66591n: , fuel filter 01 set , lub oil filter 01 no , air filter 01 no , engine oil make valvoline , rear oil , gear oil , grease , brake oil , coolent , clothes , m&l for opening and dismantling the existing wiper motor alongwith blade and blade arm and replacement of wear out and tearout parts of wiper motor alongwith replacing wiper blade with blade arm and testing on completion for tata 407 98c 66591n . make: bosch/trico or as recommended by oem complete all as specified and directed by engr in charge . , m&l for taking out front and rear wheels complete from vehicle , cleaning , polishing and overhauling of brake system ( of 02x02 nos of wheels ) by providing new wheel cylinder kit , brake shoe , brake liner , brake pipes complete ( make: tvs/bosch/tata genuine ) , cleaning & polishing of wheel drum , greasing of front and rear wheels bearing , taking out tyres , tubes of each wheels , cleaning of each wheels , disc , rims & applying two coats of anti corrosive paint after making smooth surface , re assembling of wheels and re fixing all parts & wheel alignment from authorised workshop complete with recommendations of oem and testing on completion for tata 407 98c 66591n complete all as as specified and directed by engr in charge . , m&l for supply & replacement of tail light assembly complete ( brake light and side indicator light alongwith parking light with suitable wattage of lamps ) and testing on completion make kk/lucas/tata genuine complete all as specified and directed by engr in charge suitable for tata 407 98c 66591n . , m&l for opening the complete window with inner flap , locking , opening ( outer and inner ) arrangements , servicing and minor repair for opening and closing of window mirror including replacement of locking button , window opening handle from inner and outer side , window mirror up and down handle for tata 407 98c 66591n and re fitting all and testing on completion complete all as specified and directed by engr in charge . note: parts shall be as per sample approved by engr in charge . , m&l for opening the exising self starter from the vehicle for servicing and overhauling including replacement of worn out pinion , varnish of coil , replacement of solenoid switch , carbon bush , armature winding and re assembling with engine including testing complete suitable for tata 407 98c 66591n complete all as specified and directed by engr in charge . note: make of parts mico/lucas or equivalent as recommended by oem . , m&l for taking out the existing un serviceable and detriorated wiring of tata 407 98c 66591n carefully including fuse box and ignition switch , replacement of complete vehicle wiring of headlight , deshboard light , cabin light , self starter and alternator etc as per standard manufacturer , replacement of fuse box minimum 8 nos of fuses with new fuses , ignition switch with key for tata 407 & testing on completion complete all as specified and directed by engr in charge . note: new complete wiring set as per existing size/make and colour coding . , m&l for taking down complete steering system from vehicle opening , dismentaling , taking out all parts , cleaning of serviceable parts and replacement of un serviceable parts ( steering column , tie rod , spindles , universal joints , pitman arm , steering gear box assembly , drag link assembly ) and re assembling and fixing to vehicle & testing on completion for tata 407 98c 66591n complete all as as specified and directed by engr in charge . make of un serviceable parts will be tata genuine/rane/zf . , taking down complete gear box from the vehicle opening , dismantling , taking out all parts , cleaning of serviceable parts with petrol and replacement of unserviceable parts and re assembling gear box and fixing to vehicle & testing on completion for smooth functioning of shifting of all forward and reverwse gear for tata 407 98c 66591n complete all as specified and directed . make of un serviceable parts will be tata genuine/telco genuine/zf or equivalent . ...

Military Engineer Services - Haryana

25565746 repair of mt vehicle , m&l for removing the existing seats and cushioning alongwith seat covers from the vehicle and refixing properly including replacement of broken seat supports and accesories such as springs , rods , sheets , nuts , bolts etc for tata 207 ba no 11c 091818a complete all as specified and directed by engr in charge . , supply and fixing of new seat covers and cushioning as per existing and as approved for tata 207 ba no 11c 091818a complete all as directed by engineer in charge . note: seat covers will be as approved by engineer in charge . , supply and fixing of new floor blanket inside the complete cabin of vehicle & fixing and sticking alogwith clamping properly the blanket to the cabin floor as per existing and as approved for tata 207 ba no 11c 091818a complete all as directed by engineer in charge . , supply and fixing foot mats in the cabin of vehicle as per existing and as approved for tata 207 ba no 11c 091818a complete all as directed by engineer in charge . , m&l for replacement of cabin roof clothes and rexin suitable for tata 207 ba no . 11c 091818a complete all as specified and directed by engr in charge . note: clothes and rexin sample and colour will be decided by engr in charge . , m & l for complete servicing of vehicle including replacement of following parts as recommended by oem and testing on completion for tata 207 11c 091818a: , fuel filter 01 set , lub oil filter 01 no , air filter 01 no , engine oil make valvoline , rear oil , gear oil , grease , brake oil , coolent , clothes , m&l for opening the existing alternator from the vehicle for servicing and overhauling including replacement of carbon bushes , armature winding and bush bearing and re assembling & fixing to vehicle including testing complete suitable for tata 207 ba no . 11c 091818a complete all as specified and directed by engr in charge . note: make of parts shall be mico/lucas or equivalent as recommended by manufacturer . , m&l for opening the existing wiper blade with blade arm connected to blade and replacement of wiper blade with blade arm and testing on completion for tata 207 11c 091818a . make: bosch/trico or as recommended by oem complete all as specified and directed by engr in charge . , m&l for taking out front and rear wheels complete from vehicle , cleaning , polishing and overhauling of brake system ( of 02x02 nos of wheels ) by providing new wheel cylinder kit , brake shoe , brake liner , brake pipes complete ( make: tvs/bosch/tata genuine ) , cleaning & polishing of wheel drum , greasing of front and rear wheels bearing , taking out tyres , tubes of each wheels , cleaning of each wheels , disc , rims & applying two coats of anti corrosive paint after making smooth surface , re assembling of wheels and re fixing all parts & wheel alignment from authorised workshop complete with recommendations etc testing on completion for tata 207 11c 091818a complete all as as specified and directed by engr in charge . , m&l for supply & replacement of tail light assembly complete ( brake light and side indicator light alongwith parking light with suitable wattage of lamps ) and testing on completion make kk/lucas/tata genuine complete all as specified and directed by engr in charge suitable for tata 207 11c 091818a . , m&l for opening the complete window with inner flap , locking , opening ( outer and inner ) arrangements , servicing and minor repair for opening and closing of window mirror including replacement of locking button , window opening handle from inner and outer side , window mirror up and down handle for tata 207 11c 091818a and re fitting all and testing on completion complete all as specified and directed by engr in charge . note: parts shall be as per sample approved by engr in charge . , m&l for opening the exising self starter from the vehicle for servicing and overhauling including replacement of worn out pinion , varnish of coil , replacement of solenoid switch , carbon bush , armature winding and re assembling with engine including testing complete suitable for tata 207 11c 091818a complete all as specified and directed by engr in charge . note: make of parts mico/lucas or equivalent as recommended by manufacturers . , m&l for taking out the existing un serviceable/detriorated wiring of tata 207 11c 091818a carefully including fuse box and ignition switch , replacement of complete vehicle wiring of headlight , deshboard light , cabin light , self starter and alternator etc as per standard manufacturer , replacement of fuse box minimum 8 nos of fuses with new fuses , ignition switch with key for tata 207 & testing on completion complete all as specified and directed by engr in charge . note: new complete wiring set as per existing size and make and colour coding . , m&l for denting and painting work where required on complete body of vehicle , removing old paint by scraping , cleaning with caustic soda or other suitable chemical and making surface even smooth by applying putty , rubbing , cutting , polishing all as required and applying one coat of primer and two coat of deco paint by spray painting as per existing paint and shape by preventing non painting parts ( as directed by engr in charge ) including applying two coats of anti corrosive black bitumen paint to flooring both sides of wheel mud gaurd under coverage and aluminium paint on silencer , writing vehicle ba number as per existing size complete all as specified and directed by engr in charge for tata 207 11c 091818a . ...

Military Engineer Services - Haryana

24513163 ge / sra / t 45 of 2019 2020 repairs maint of t and p plants rr plants with allied works at af stn sirsa , repairs to tata tipper , taking down the existing clutch system from tata tipper , with replacement of clutch plate , pressure plate , withdral bearing etc . and refixing to vehicle , testing on complition for smooth working , complete all as specified and as directed . ( make : tata genuine / ceekay / repco ) , opening dynamo from tata tipper for servicing / overhauling including replacement of carbon bushes , armature winding and bush bearing , re assembling and fixing to vehicle including testing , complete all as specified and as directed . make : mico / lucas or as approved . , opening self starter from tata tipper for servicing / overhauling including replacement of worn out pinoin , varnish of coil , solenoid switch , carbon bush , armature winding and re assembling with engine , complete all as specified and as directed . make : mico / lucas or equivalent as recommended by manufacturers . , complete servicing of diesel engine of tata tipper including replacement of air filter , fuel filters , lube oil filter , fan belt & other unserviceable fuel pipes / hose pipes etc and other accesories alongwith change of old engine oil all as per existing shape / size . make of filters / engine oil / fan belt / pipes used shall be as per oem . , repairing / servicing carefully of water pump alongwith waterbody assembly with necessary accessories for tata tipper , with repalcing unserviceable parts as existing shape / size , re fitting the same , testing on completion , complete all as specified and as directed . , s&f brake master cylinder kit suitable for tata tipper including taking out existing leakage brake master cylinder kit from the vehicle , complete all as specified and as directed . make : tata or as existing model , s&f cabin roof clothes / rexin ( as approved ) suitable for tata tippr including removing existing cabin roof clothes / rexin , complete all as specified and as directed . note : clothes / rexin sample and colour will be decided by engineer in charge . , front wind glass ( as approved / as per existing size / shape ) suitable for tata tipper , checking / servicing of locking system and minor repairing of opening / closing of window glass including taking down / out unserviceable front wind glass by inner board / cover , complete all as specified and as directed . make : tata or as approved , seat covers ( as approved / as per existing ) suitable for tata tipper and fixing properly including taking out wornout upholstry from vehicle , complete all as specified and as directed . note : seat covers will be as approved by ge / engineer in charge . , taking down the chocked radiator with hoses , clamps from the vehicle , cleaning of outer fins , repair the leakage copper fins with compressed air and internally with superior quality c cleaner and refixing the same with new hoses , clamps & testing on complition for tata tipper complete all as specified and directed by engr in charge . , denting work where needed on complete vehicle tata tipper , removing old paint by scraping , cleaning with caustic soda and making surfaces even and smooth by applying putty , rubbing , cutting , polishing all as required and applying one coat of primer and two coat of nc paint by spray painting as per existing paint / shape by preventing non painting parts ( as ordered by engineer in charge ) including application two coats of anti corrosive black paint to flooring both sides of wheel mud guard under coverage , writing vehicle ba no . , firm name , complete all as specified and as directed . note : colour of paint & writing vehicle ba no . & firm name will be approved by engineer in charge . , taking out front / rear wheels complete from tata tipper , cleaning , polishing & overhauling of brake system ( 2x4 no . of wheels ) by providing new wheel cylinder kit , brake shoe , brake liner , brake pipes complete ( make : tvs / rane / bosch ) , cleaning & polishing of wheel drum , greasing of front and rear wheels bearing , taking out tyres , tubes of each wheels , cleaning of each wheels / disc / rims and applying two coats of anti corrosive paint after obtaining a smooth surface , re assembling of wheels and other parts including wheel alignment from authorised workshop , testing on completion , complete all as as specified and as directed . , taking down complete gear box from tata tipper by opening , all parts , cleaning of serviceable parts with petrol , replacement of unserviceable parts , re assembling gear box and re fixing to vehicle , testing on completion for the smooth functioning of shifting of all forward and reverse gear , complete all as specified and as directed . make : tata genuine or as existing model . , repairs to ashok leyland tipper , taking out and opening carefully fuel injection pump from ashok leyland tipper , complete servicing / repair / replacement of following unserviceable parts ( as approved / as per existing size and make ) , grinding of nozzles complete and re fixing the same , testing on completion , complete all as specified and as directed : ( a ) bearing 06nos . ( b ) bearing bush 06 nos . ( c ) delivery valve 06 nos . ( d ) fuel pipe line 06 nos . ( e ) niddle valve 06 nos . ( e ) plunger 06 nos . , opening dynamo from ashok leyland tipper for servicing / overhauling including replacement of carbon bushes , armature winding and bush bearing , re assembling and fixing to vehicle including testing , complete all as specified and as directed . make : mico / lucas or as existing model . , opening self starter from ashok leyland tipper for servicing / overhauling including replacement of worn out pinoin , varnish of coil , replacement of solenoid switch , carbon bush , armature winding and re assembling with engine , complete all as specified and as directed . make : mico / lucas or as existing model . , complete servicing of diesel engine of ashok leyland tipper including replacement of air filter , fuel filters , lube oil filter , fan belt & other unserviceable fuel pipes / hose pipes etc and other accesories alongwith change of old engine oil all as per existing shape / size . make of filters / engine oil / fan belt / pipes used shall be as per oem . , repairing , servicing carefully of water pump alongwith waterbody assembly with necessary accessories for ashok leyland tipper , repalcing unserviceable parts with existing shape / size , re fitting the same , testing on completion , complete all as specified and as directed . , brake master cylinder kit suitable for ashok leyland tipper including taking out existing leakage brake master cylinder kit from the vehicle , complete all as specified and as directed . make : ashok leyland or as existing model . , cabin roof clothes / rexin ( as approved ) suitable for ashok leyland tipper including removing existing cabin roof clothes / rexin , complete all as specified and as directed . note : clothes / rexin sample and colour will be approved by engineer in charge . , taking down the existing clutch system from ashok leyland tipper , replacement of clutch plate , pressure plate , withdral bearing etc . and fixing to vehicle , testing on complition for smooth working , complete all as specified and as directed . make : ashok leyland genuine / ceekay / repco , seat covers ( as approved / as per existing ) suitable for ashok leyland tipper and fixing properly including taking out wornout upholstry from vehicle , complete all as specified and as directed . note : seat covers will be as approved by engineer in charge . , repairing / overhauling of complete hydraulic pumping set , valve block with all accessories ( as per existing size & make ) suitable for ashok leyland tipper including taking down / out unserviceable hydraulic pumping set , valve...

Military Engineer Services - Haryana

23973066 repair / maintenance of t and p plant ( rr plant ) with allied works at af stn sirsa , repairs to tata tipper , m&l taking down the existing clutch system from tata tipper , replacement of clutch plate , pressure plate , withdral bearing etc . and refixing to vehicle , testing on complition for smooth working , complete all as specified and as directed . ( make : tata genuine / ceekay / repco ) , m&l opening dynamo from tata tipper for servicing / overhauling including replacement of carbon bushes , armature winding and bush bearing , re assembling and fixing to vehicle including testing , complete all as specified and as directed . make : mico / lucas or as approved . , m&l opening self starter from tata tipper for servicing / overhauling including replacement of worn out pinoin , varnish of coil , replacement of solenoid switch , carbon bush , armature winding and re assembling with engine , complete all as specified and as directed . make : mico / lucas or equivalent as recommended by manufacturers . , m&l for complete servicing of diesel engine of tata tipper including replacement of air filter , fuel filters , lube oil filter , fan belt & other unserviceable fuel pipes / hose pipes etc and other accesories alongwith change of old engine oil all as per existing shape / size . make of filters / engine oil / fan belt / pipes used shall be as per oem . , m&l repairing / servicing carefully of water pump alongwith waterbody assembly with necessary accessories for tata tipper , repalcing unserviceable parts with existing shape / size , re fitting the same , testing on completion , complete all as specified and as directed . , m&l brake master cylinder kit suitable for tata tipper including taking out existing leakage brake master cylinder kit from the vehicle , complete all as specified and as directed . make : tata or as approved , m&l cabin roof clothes / rexin ( as approved ) suitable for tata tippr including removing existing cabin roof clothes / rexin , complete all as specified and as directed . note : clothes / rexin sample and colour will be decided by engineer in charge . , m&l front wind glass ( as approved / as per existing size / shape ) suitable for tata tipper , checking / servicing of locking system and minor repairing of opening / closing of window glass including taking down / out unserviceable front wind glass by inner board / cover , complete all as specified and as directed . make : tata or as approved , m&l seat covers ( as approved / as per existing ) suitable for tata tipper and fixing properly including taking down wornout upholstry from vehicle , complete all as specified and as directed . note : seat covers will be as approved by ge / engineer in charge . , m&l for taking down the chocked radiator with hoses , clamps from the vehicle , cleaning of outer fins / repair the leakage copper fins with compressed air and internally with superior quality c cleaner and refixing the same with new hoses , clamps & testing on complition for tata tipper complete all as specified and directed by engr in charge . , m&l denting work where needed on complete vehicle tata tipper , removing old paint by scraping , cleaning with caustic soda and making surfaces even and smooth by applying putty , rubbing , cutting , polishing all as required and applying one coat of primer and two coat of nc paint by spray painting as per existing paint / shape by preventing non painting parts ( as ordered by engineer in charge ) including application two coats of anti corrosive black paint to flooring both sides of wheel mud guard under courage , writing vehicle ba no . , firm name , complete all as specified and as directed . note : colour of paint & writing vehicle ba no . & firm name will be decided by engineer in charge . , m&l taking out front / rear wheels complete from tata tipper , cleaning , polishing & overhauling of brake system ( 2x4 no . of wheels ) by providing new wheel cylinder kit , brake shoe , brake liner , brake pipes complete ( make : tvs / rane / bosch ) , cleaning & polishing of wheel drum , greasing of front and rear wheels bearing , taking out tyres , tubes of each wheels , cleaning of each wheels / disc / rims and applying two coats of anti corrosive paint after obtaining a smooth surface , re assembling of wheels and re fixing all parts including wheel alignment from authorised workshop , testing on completion , complete all as as specified and as directed . , m&l taking down complete gear box from tata tipper by opening , dismantal ing , taking out all parts , cleaning of serviceable parts with petrol , replacement of unserviceable parts , re assembling gear box and re fixing to vehicle , testing on completion for the smooth functioning of shifting of all forward and reverse gear , complete all as specified and as directed . make : tata genuine or as approved . , repairs to ashok leyland tipper , m&l opening / dismantling carefully fuel injection pump from ashok leyland tipper , complete servicing / repair / replacement of following unserviceable parts ( as approved / as per existing size and make ) , grinding of nozzles complete and re fixing the same , testing on completion , complete all as specified and as directed : ( a ) bearing 06no . ( b ) bearing bush 06 no . ( c ) delivery valve 06 no . ( d ) fuel pipe line 06 no . ( e ) niddle valve 06 no . ( e ) plunger 06 no . , m&l opening dynamo from ashok leyland tipper for servicing / overhauling including replacement of carbon bushes , armature winding and bush bearing , re assembling and fixing to vehicle including testing , complete all as specified and as directed . make : mico / lucas or as approved , m&l opening self starter from ashok leyland tipper for servicing / overhauling including replacement of worn out pinoin , varnish of coil , replacement of solenoid switch , carbon bush , armature winding and re assembling with engine , complete all as specified and as directed . make : mico / lucas or equivalent , m&l for complete servicing of diesel engine of ashok leyland tipper including replacement of air filter , fuel filters , lube oil filter , fan belt & other unserviceable fuel pipes / hose pipes etc and other accesories alongwith change of old engine oil all as per existing shape / size . make of filters / engine oil / fan belt / pipes used shall be as per oem . , m&l repairing / servicing carefully of water pump alongwith waterbody assembly with necessary accessories for ashok leyland tipper , repalcing unserviceable parts with existing shape / size , re fitting the same , testing on completion , complete all as specified and as directed . , m&l brake master cylinder kit suitable for ashok leyland tipper including taking out existing leakage brake master cylinder kit from the vehicle , complete all as specified and as directed . make : ashok leyland or as approved , m&l cabin roof clothes / rexin ( as approved ) suitable for ashok leyland tipper including removing existing cabin roof clothes / rexin , complete all as specified and as directed . note : clothes / rexin sample and colour will be decided by engineer in charge . , m&l taking down the existing clutch system from ashok leyland tipper , replacement of clutch plate , pressure plate , withdral bearing etc . and fixing to vehicle , testing on complition for smooth working , complete all as specified and as directed . ( make : ashok leyland genuine / ceekay / repco ) , m&l seat covers ( as approved / as per existing ) suitable for ashok leyland tipper and fixing properly including taking down wornout upholstry from vehicle , complete all as specified and as directed . note : seat covers will be as approved by ge / engineer in charge . , m&l for repairing / overhauling of complete hydraulic pumping set , valve block with all accessories ( as per existing size & make ) ...

Haryana Vidyut Prasaran Nigam Limited - Haryana

18938739 tender for a ) painting work of electrical equipments in switch yard at 132k substation, kharkhoda. b ) painting work of electrical equipments in 220kv switch yard 1, ptps panipat. : 1 11 / 0.4kv, 200kva s / stn t / f 2 132 / 11kv, 10 / 16mva t 1 t / f 3 132 / 33kv, 20 / 25mva t 2 t / f & t 3 t / f 4 132kv bay mks 5 132kv cts & cvt 6 132kv la 7 132kv gcbs 8 132kv isolators , 9 132kv l&e switch 10 132kv isolator motor driving box 11 33kv cts / pts 12 33kv la 13 33kv vcbs 14 33kv isolators 15 33kv l&e switch 16 33kv isolator motor driving box1 scrapping , washing of t / f with caustic soda, painting with one coat of anticorrosive paint wherever required , one coat of spray painting of body of 220 / 132kv, 100 mva t / f t 1 and t 2 including 132kv ncts ( with lt gray isi mark paint ) with demarcation of red, yellow & blue paint on bushing tops. 2 scraping, washing and applying one coat of anti corrosive paint on rusted portions, one coat of primer & two coats of painting ( with lt grey asian / nerolac make paint, 1st quality, isi mark ) of 220 / 132kv mks. other repairs e.g. set right of locking system, door welding ( wherever required ) , included. 3 scraping, washing and applying one coat of anti corrosive paint on rusted portions, one coat of primer & two coats of painting ( with lt grey asian / nerolac make paint, 1st quality, isi mark ) of 220 / 132 kv gcbs. 4 scraping, washing and applying one coat of anti corrosive paint on rusted portions, one coat of primer & two coats of painting ( with lt grey asian / nerolac make paint, 1st quality, isi mark ) of 220 kv cts. 5 scraping, washing and applying one coat of anti corrosive paint on rusted portions, one coat of primer & two coats of painting ( with lt grey asian / nerolac make paint, 1st quality, isi mark ) of 220 kv isolator boxes....

Military Engineer Services - Haryana

14366041 provision of certain repair to internal water supply, sanitary items and day to day misc b r works at af stn gurgaon under ge p af gurgaon, ge ( p ) af / gur 70 / 2017 18 ( 2nd call ) 1. (a) factory made panel/ flush door shutters 2. plywood 3. laminated sheets 4. prelaminated particle board 5. pvc water tank 6. chemical water proofing compound 7. intergral water proofing treatment (liquid) 8. steel windows/ ventilators (as per is:1038:1983) 9. cold rolled steel doors & windows 10. glazed tiles, water resistant tiles/non skid tiles 11. aluminium sections 12. vitrified tiles 13. putty 14. ac pipes and fittings 15. ac sheets 16. pcc interlocking tiles/pavers 17. pcc tiles/terrazzo tiles/chequered tiles 18. acid resistant tiles 19. pvc flushing cistern is 774 1984 20. looking mirror 21. sanitary fittings 22. seat & cover for wc 23. galvalume/zincalume sheet 24. aluminium and brass mongry 25. galvanised iron tube 26. door closers 27. mortice locks 28. cement based paint 29. synthetic enamel paint 30. red oxide primer 31. oil bound distemper 32. plastic emulsion paints (distemper and emulsion) 33. chlorinated rubberised paint/epoxy paint/anti corrosive paint. 34. 100% acrylic weather proof exterior paint 35. wood primer pink 36. glass(plain frosted tinted)/ mirrors 37. cement base putty 38. pvc rain water pipes 39. ci rain water pipes 40. pvc flooring tiles /sheets 41. water proofing membrane 42. fire clay bricks and tiles 43. glazed fire clay kitchen sinks 44. bib tap, stop valve, pillar taps 45. fancy bib tap, stop valves, pillar taps, wall mixing unit 46. false ceiling with grid and boards 47. rolling shutters 48. rust prevention anti corrosive chemicals 49. sealing compound for joints in concrete 50. fibre reinforced concrete (pfrc) manhole covers 51. pressed steel door/ window frames...