Food Corporation Of India - Haryana

39807411 tender for annual repair and maintenance of and misc. repair works for the year 2023 24 at fsd karnal; 1 dismantling barbed wire or flexible wire rope in fencing including making rolls and stacking within 50 metres lead. 2 dismantling steel work in single sections including dismembering and stacking within 50 metres lead in:channels, angles, tees and flats 3 demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge.in cement mortar 4 dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead 5 demolishing r.c.c. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge 6 dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: asbestos cement sheet 7 earth work in excavation by mechanical means ( hydraulicexcavator ) / manual means over areas ( exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan ) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by engineer in charge.all kinds of soil 8 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level :1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) 9 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.cold twisted bars 10 centering and shuttering including strutting, propping etc. and removal of form for :foundations, footings, bases of columns, etc. for mass concrete 11 centering and shuttering including strutting, propping etc. and removal of form for :lintels, beams, plinth beams, girders, bressumers and cantilevers 12 structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 13 providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all work up to plinth level : 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources ) 14 centering and shuttering including strutting, propping etc. and removal of form for : columns, pillars, piers, abutments, posts and struts 15 reinforced cement concrete work in walls ( any thickness ) , including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing andreinforcement :1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources ) 16 centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platform 17 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources ) . 18 removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m ( stacks of cleaned bricks shall be measured ) :from brick work in cement mortar 19 brick work with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in foundation and plinth in: cement mortar 1:6 ( 1 cement : 6 coarse sand ) with available bricks ( with available bricks ) 20 brick work with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in : cement mortar 1:6 ( 1 cement : 6 coarse sand ) with available bricks ( with available bricks ) 21 brick work with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in : cement mortar 1:6 ( 1 cement : 6 coarse sand ) 22 centering and shuttering including strutting, propping etc. and removal of form for small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like 23 supplying at site angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete. 24 providing and laying cement concrete in retaining walls, return walls, walls ( any thickness ) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:2:4 ( 1 cement : 2 coarse sand ( zone iii ) : 4 graded stone aggregate 20 mm nominal size 25 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 ( 1 cement: 6 fine sand ) 26 12 mm cement plaster of mix :1:6 ( 1 cement: 6 fine sand ) 27 6 mm cement plaster of mix : 1:3 ( 1 cement : 3 fine sand ) 28 fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m ( minimum ) , between the two posts fitted and fixed with g.i. staples, turn buckles etc. complete. ( cost of posts, struts, earth work and concrete work to be paid for separately ) . payment to be made per metre cost of total length of barbed wire used. with g.i. barbed wire 29 distempering with 1st quality acrylic distemper, having voc ( volatile organic compound ) content less than 50 grams / litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.two coats 30 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : one or more coats on old work 31 regrading terracing of mud phaska covered with tiles or brick, in cement mortar by dismantling tiles or bricks, removing mud plaster, preparing the surface of mud phaska to proper slope, relaying mud plaster gobri leaping and tiles or bricks, grouted in cement mortar 1:3 ( 1 cement : 3 fine sand ) , including replacing unserviceable tiles or bricks with new ones and disposal of unserviceable material to the dumping ground ( the cost of the new tiles or brick excluded ) , all complete as per direction of engineer in charge. 32 structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 33 credit of old iron scrap including loading / unloading / disposal etc as per direction of engineer in charge 34 credit for old unserviceable ac sheets 35 disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by engineer in charge, beyond 50 m initial lead, for all leads including all lifts involved....

Public Health Engineering Department - Haryana

39577509 tender for annual maintenance water supply scheme sherpura , taking out filter media all layer & bed plate after washing and replacing the same at at water works sherpura and all other works contingent thereto...

Public Health Engineering Department - Haryana

39269442 manheru village providing installing of 05 nos shallow tubewell near dadri feeders taking out washing and placing of filter media upto bed plates and washing of drains and providing and placing of top layer filter media in 3 no filter bed of size 4 manheru village providing an installing of 05 nos shallow tubewell near dadri feeders taking out washing and placing of filter media upto bed plates and washing of drains and providing and placing of top layer filter media in 3 no filter bed of size...

Public Health Engineering Department - Haryana

37236362 providing functional house hold tap connection and laying of pipe line under jjm in village hazampur “taking out new filter mediaall layers of filter media, bed plates & placing the same after washing 4 nos. filter beds, repair of v notch at water works dhandheri and all other works contingent thereto...

Public Health Engineering Department - Haryana

36194794 badala and dhani mahabir providing functional house hold connection and laying of di pipe line for w s under jjm taking out of new filter media and washing of filter media beds plates and placing the same after washing 2 nos. filter bed, repair of s s tank, repair of inlet channel in village badala and all other works contingent thereto...

Public Health Engineering Department - Haryana

35232755 dhandheri – providing functional house hold tap connection and laying of di balance pipe line under jjm “taking out of new filter media all layers of filter media, beds plates & placing the same after washing 3 nos. filter beds, repair of v notch at w / works dhandheri and all other works contingent theret...

Military Engineer Services - Haryana

34996897 special repair of equipment shed no g 149, g 150, g 151 g 152 of 140 ad regt and provision of drainage from offrs mess bldg no p 144 to main drain in b area, allenby line of age br i under ge ( south ) ambala cantt material and labour for brick work with sub class ‘b’ bricks, straight or curved on plain exceeding 6 metre mean radius in cement mortar ( 1:6 ) including demolition of brick work built in cement mortar including demolition of old brick / stone masonry built in cement mortar of any description including all quoins, archs, pillars etc complete all as specified and directed. 2 material and labour for brick work ( except bricks ) straight or curved on plan exceeding 6 metre mean radius built in cm 1:6 ( old size brick ) including demolition of old brick masonry built in cement mortar of any description including all quoins, archs, pillars etc complete all as specified and directed. 3 taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed. 4 material and labour for rendering 15 mm thick on any faces of old brick work in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed. 5 material and labour for rendering 15 mm thick on fair faces of new brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and directed. 6 material andlabour for preparation of exposed brick wall surface by cleaning the surface wire brush to remove all dirt / loose materials from the bricks and from the joints between the bricks. prepared surface should be then washed with diluted hcl acid ( dilution ratio of 1:50 ) for three times in a day for two days. after acid wash surface should be allowed to be air dried for one day. note : further treatment over the surface so achieved will be carried out only after approved of the same by ge. 7 material and labour for carrying out efflorescence treatment to unplastered wall surface comprising of the following specifications and sequence with and including 15 mm thick rendering in cm 1:4 finished even and smooth without using extra cement : ( a ) prime the prepared surface with one of the following product mixed with cement in 1:1 ratio as bonding agent : ( i ) pidicrete urp of m / s pidilite. ( ii ) sika latex of m / s sika. ( iii ) nitobond sbr latex of m / s fosroc. ( b ) immediately after priming the surface pmm ( polymer modified mortar ) to be applied “by hand” while the prime is tacky. pmm should be prepared by mixing one of the following compounds in cement mortar 1:3 as per manufacturer’s instructions: ( i ) pidicrete urp of m / s pidilite. ( ii ) sika latex of m / s sika. ( iii ) nitobond sbr latex of m / s fosroc. ( c ) pmm surface should be allowed to dry for one day. after that it should painted with two coats of one of the following compound mixed with cement only in ratio of 1 ( selected compound ) : 1:5 ( cement ) : ( i ) pidicrete urp of m / s pidilite. ( ii ) sika latex of m / s sika. ( iii ) nitobond sbr latex of m / s fosroc. ( d ) now apply two coats of one of the following compound over the surface. these compounds are to be used as per manufacturer’s instructions: ( i ) pidifin 2k of m / s pidilite. ( ii ) brush coat of m / s sika. ( iii ) brush bond of m / s fosroc.note : both coats should be perpendicular to each other and gap between two coats shall be minimum 6 hours. ( e ) sprinkle loose coarse sand after second coat while surface is tacky.note: ( i ) the item will be executed by authorized applicator only of the selected / approved company. contractor shall submit details of authorised applicator for approval of ge before commencement of work in respect of above item. ( ii ) every stage of work will be approved by ge, then only next layer will be executed by contractor. 8 material and labour for rough cast plaster with and including 15mm thick rendering in cm 1:3 on brick wall or concrete surface as specified in clause 14.22 of ssr part i complete all as specified and directed.note: ( i ) after applying the under coat of cement and sand mortar 1:3 not less than 10 mm thick andwhile it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravelaggregate ( which is generally of size between 6 to 12 mm depending on the texture required ) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even. ( ii ) the mix of cement and sand shall be made slightly wetter than normal for rendering to ensurethat larger aggregates are thoroughly covered 9 material and labour for preparation of new plastered surfaces of walls and applying three coats of white wash on wall, complete all as specified and directed. 10 material and labour for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of alkali resistant primeron walls complete all as specified and directed. 11 material andlabour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper with hand roller, over a coat of alkaline resistant primer over a coat of wall care puttynot less than 1mm thick as per manufacturers instruction complete all as specified and directed. 12 material andlabour for preparation of old plastered surfaces of walls and applying two coats of white wash complete all as specified and directed. 13 material and labour preparation of old plastered surfaces of walls and applying one coat of cement base paint complete all as specified and directed. 14 supply andfixing of pre painted galvalume aluminium zinc coating gi based corrugatedsteel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa tensile strength as in roof covering / cladding to wall, fixed with self tapping screws or j type hooks including rubber washer etc complete including dismantling asbestos cement corrugated or semi corrugated sheets etc; complete all as specified and as directed. 15 supply andfixing of pre painted galvalume aluminium zinc coating gi based galvanised plain mild steel sheeting 0.50 mm thick of any colour, having 550 mpa tensile strength as in roof covering / ridges and fixed with self tapping screws or j type hooks including rubber washer etc complete including dismantling asbestos cement corrugated or semi corrugated sheets etc; complete all as specified and as directed. 16 dismantling timber scantling 40 sq. cm and over in section, in any position of unframed / framed work complete all as specified and directed. 17 material and labour for preparation of old painted steel surfaces of any description not otherwise described, over 10 cm in width or girth and applying one coat of synthetic enamel paint with approved shade complete all as specified and directed. 18 material and labour for taking down of rolled mild steel roof trusses ( framed ) of clear span above 08.00 metre and upto 12.00 metre any type, taking in safe costudy and refixing the same with and including using new nut bolts, welding & distance pieces, cleats etc., after completion of truss connected repair work etc complete all as specified anddirected. note: any damage to the existing truss during dismantling or refixing etc, shall be made good by the contractor with the same specifications as per existing work, without any extra cost to the govt. 19 dismatling of mild steel beam, purlin of existing truss andrefixing the same ( using nut bolt, welding ) rolled mild steel plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases, splices, angle brackets, cleats & other connections gde fe410 0 or fe 310 o complete all as specified and as directed. 20 supply and fixing of rolled mild steel sections as in main & cross beams, hip & jack rafters; purlins where connected to common rafters & running rails & guides for sliding doors; fixed with angle cleats or other connecting plates gde fe410 0 or fe 310 o complete all as specified and as directed. 21 supply andfixing of rolled mild steel work in roof trusses ( framed ) , trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing ( beam, tee, angle, channel or flat sections ) including distance pieces, cleats etc., quality confirming tofe 410 w ( gde e 250 ) quality a, complete, all as specified and as directed. 22 supply andfixing of mild steel plates ( plain or chequered ) channels, square cut or notched ( ordinary and counter sunk ) forming holes, with riveted, bolted or welded attachment conforming to grade fe 410 ( gde 250 ) , complete all as specified and directed. 23 material and labour for steel screw bolts, machine made, dia of neck 11 to 15mm with hexagonal or square head one end and screwed the other or screwed both ends, each screwed end to be fitted with washer and one hexagonal or square nut exceeding 22.5 cm and not exceeding 30cm long, complete all as specified and directed. 24 material and labour for two coats of synthetic enamel paint on steel surfaces over a coat of red oxide primerincludingpreparation of new steel surfaces of any description not otherwise described over 10 cm width or girth, complete all as specified and as directed. 25 material and labour for hardcore of gauge not exceeding 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. 26 material and labour for 150mm thick pcc 1:2:4 type b2 using 40mm graded mechanically crushed stone aggregate as in hardstanding / paths, finishing the concrete surface even and smoothwithout using extra cement including formingjoints and fillingwith mixture of bitumen and sand in ratio ( 1:1 ) by weight including necessary formwork etc and including demolition of existing old cement concrete in ground floors and pavings n.exc 15cm thickness ( below or above ) ground level complete all as specified and directed. 27 material and labour for 50mm thick pcc ( 1:3:6 ) type c 1 using 20mm graded mechanically crushedstone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10mm wide, 30mm deep joints at the rate of 3.00 mtr centre to centre and at every turning & filling the joints with bitumen & sand mixture including demolition of cement concrete in ground floor and pavings not exceeding 15 cm below or above ground level etc complete all as specified and directed. 28 surface excavation not exceeding 30 cm deep, averaging 15 cm deep and getting out in soft / loose soil, complete all as specified and directed. 29 material and labour for 100mm thick pcc ( 1:4:8 ) type d 2 using 40mm graded mechanically crushed stone as in sub base of floor / hard standing finished, complete all as specified and directed. 30 material and labour for providing and laying 80mm thick factory made chamfered edge cement concrete paver block of m 40 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size / shape, made by table vibratory method using pu mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed 31 material and labour for providing and laying of precast pcc solid concrete block, grade c confirming to is 2185 ( part i ) 2005 of 45 cm high, 10 cm thick and of suitable width including chamfers, weatherings, throating etc as in kerb continuous edging jointed in cement mortar 1:4 and struck flush pointing as the work proceeds and finishing with neat cement flush joint, complete all as specified and directed. 32 material andlabour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.11sqm but not exceeding 0.18 sqm, 7 to 8 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg / square metre and pointed in white or coloured cement to match the surface over and including15mm thick screed bed or layer in cement mortar ( 1:4 ) including dismantling of existing tiles etc including cement mortar bedding ( but not backing ) andrubbish off the premises complete all as specified and directed. 33 material and labour forpremium quality coloured glazed ceramic tiles ( 300x 450x 7mmthick ) in vertical surfacesand jointed in neat cement slurry @ 3.00 kg / square metre and pointed in white or coloured cement to match including rendering 10mm thick in cement plaster 1:3 including dismantling of old floor or wall tiling including cement mortar bedding and removing the rubbish outsidethe defence land complete all as specified and as directed. 34 material and labour for machine cut kota stone slab 20 25 mm thick ( size of each stone not less than 55cm x 55cm ) , laid in flooring, over and including cement screed bed 20mm thick in cement mortar ( 1:4 ) base set and jointed in neat cement slurry @ 3.00 kg / sqm and pointed in white or coloured cement to match the surface mixed with pigment to match shade of the slab over and including 25 mm thick cement concrete type b 0, 1:2:4 ( 12.5 mm graded aggregate ) as in levelling course, including cutting, waste, rubbing and polishing ( mirror finish ) including dismantling of existing stone slab / tiles etc including pcc and cement mortar bedding andrubbish off the premises complete all as specified and directed. 35 material and labour for machine cut kota stone slab 18 20 mm thick ( size of each stone not less than 55cm x 55cm ) , laid on vertical surfaces of skirting / dado, over and including cement screed bed 15 mm thick in cement mortar ( 1:3 ) and set and jointed in neat cement slurry @ 3.00 kg / sqm and pointed in white or coloured cement to match the surface mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing ( mirror finish ) including dismantling of existing stone slab / tiles etc including cement mortar bedding ( but not backing ) andrubbish off the premises complete all as specified and directed. 36 supply and fixing in repair of 5.5mm thick looking mirror of selected quality, beveled edge 450mmx600mm glass mounted on 6mm thick ac building board with aluminiumbeading andrubber packing and fixed to wall with wooden plug with chromium plated brass screw and cup washer complete all as specified and directed. 37 supply & fixing ( in repair ) vitreous china wash down water closet pedestal pattern ( ewc ) , white including connection to trap and to flushing pipe with ‘p’ or ‘s’ trap, making good to floor, plastic water closet seat cover with mild steel chromium plated hinges and chromium plated jet spray with 1.5 meter flexible ldpe pipe jointed with pipe complete all as specified and directed. 38 supply and fixing in repair of health faucet with 8mm dia, 1metre long flexible tube and wall hook complete all as specified and directed. 39 supply & fixing in repair of vitreous china wash hand basin white flat back of size 550x440mm including ci brackets and 15mm chromium plated pillar tap, pvc connection 450 mm long having ptmt nuts and 32 mm dia brass chromium plated waste coupling and making good to disturbed portion including32 mm dia pvc waste pipe etc., complete all as specified and directed. 40 supply and fixing in repair of 10 litre capacity virgin polypropylene cistern, white, isi marked, coloured at low level complete including supply and fixing45 cm pvc connection, pvc bend / flush pipe andmaking all connection , and removal old complete all as specified and directed. 41 supply and fixingin repair of vitreous china half stall urinal complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, pvc waste pipe, flush pipe, cp waste fitting, grating and union for discharge pipe complete all as specified and directed. 42 supply and fixing in repair of cp bib tap screwed down high pressure, long body, cast copper alloy, chromium plated with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified. ( note : weight of bib tap shall not be less than 0.575 kg ) 43 supply and fixing of gi tubing, isi marked, 15mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors including necassary cutting / chasing / pinning in wall and making good the disturbed surfaces as per existing whereever required, including taking down of old tubing as existing at site and removal, complete all as specified and as directed. 44 supply and fixing of gi tubing, isi marked, 20mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors including necassary cutting / chasing / pinning in wall and making good the disturbed surfaces as per existing whereever required, including taking down of old tubing as existing at site and removal, complete all as specified and as directed. 45 refixing old serviceable steel water tubing of 15 mm bore, in new or old position, any grade, including s&f new fittings as required, fixed to walls and ceilings or laying in floors including necassary cutting / chasing / pinning in wall and making good the disturbed surfaces as per existing whereever required , including taking down of old tubing as existing at site and removal, complete all as specified and as directed 46 refixing old serviceable steel water tubing of 20 mm bore, in new or old position, any grade, including s&f new fittings as required, fixed to walls and ceilings or laying in floors including necassary cutting / chasing / pinning in wall and making good the disturbed surfaces as per existing whereever required , including taking down of old tubing as existing at site and removal, complete all as specified and as directed 47 supply and fixing in repairs, water storage tank of 500 ltr capacity, hdpe double layer, isi marked, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, isi marked, screwed andsuitable for iron pipe 20 mm bore complete all as specified and directed. note: make of tank shall be engraved on the tank. 48 supply andfixing in repair of angle valve, 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with capstain head, heavy with adjustable wall flange, and removal old complete all as specified and directed. 49 supply & fixed in repair of stop cock, fancy type, chromium plated, long shank and cup ( concealed type ) screwed down high pressure with crutch or butterfly handle screwed both ends suitable for 15mm bore pipe, complete all as specified and directed. ( note : weight of stop cock shall not be less than 0.575 kg ) 50 supply and fixingin repair of chromium plated shower rose with swivel joints and including fixed to gi tubing 15mm bore size of shower not less than 125mm complete all as specified and directed. 51 supply and fixing in repair of chromium plated soap dish with fitting fixed with brass screws complete all as specified and directed. 52 supply and fixing in repair of 20 mm dia gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed. 53 supply andfixing in repair of brass chromium plated tubular towel rail, 20 mm dia, ‘d’ type 60 cm long between flanges complete all as specified and directed. 54 excavating in trenches, not exceeding 1.50 m wide & not exceeding1.5m depth & getting out in hard / dense soil complete all as specified and directed. 55 supply and fixing of pvc ( swr ) 75 mm pipe single socket in any length with rubber ring joints laid in floor or trenches includingdismantling ofpipes of any description any length etc complete all as specified and as directed. 56 supply and fixing of pvc ( swr ) 110 mm pipe single socket in any length with rubber ring joints laid in floor or trenches includingdismantling ofpipes of any description any length etc complete all as specified and as directed. 57 supply and fixing of pvc ( swr ) 110 mm pipe single socket in any length with rubber ring joints fixed to wall with ms clamps including dismantling ofpipes of any description any length etc complete all as specified and as directed. 58 supply and fixingin repair of 110 mm bore pvc ( swr ) bend with access door including jointing with solvent cement, complete all as specified and directed. 59 supply and fixingin repair of pvc ( swr ) 110 mm to 75 mm dia, reducers complete all as specified and directed. 60 supply and fixing in repair of 110 mm bore pvc ( swr ) , junction single t ( equal or unequal ) , including jointing with solvent cement, complete all as specified and directed. 61 supply and fixing in repair of pvc ( swr ) floor trap 75mm dia plain with pvc grating including jointing with solvent cement complete all as specified and directed. 62 taking down chowkats or frames with shutter, areanot exceeding 1.50 square metre ( w / o taking off shutters from frames ) and removing from site, including cutting holes in wall / concrete for taking out existing hold fasts and making good the disturbed portion of jambs andadjoining surfacesin cm ( 1:3 ) and finishing the surfaces to match with existing finish complete all as specified and directed. 63 taking down chowkats or frames with shutter, areaexceeding 1.50 square metrebut not exceeding 4 square metre ( w / o taking off shutters from frames ) and removing from site, including cutting holes in wall / concrete for taking out existing hold fasts and making good the disturbed portion of jambs andadjoining surfacesin cm ( 1:3 ) and finishing the surfaces to match with existing finish complete all as specified and directed. 64 supply and fixing of pressed steel frames for doors of size 125 x 60mm, 1mm thick, with one or more rebates including, hold fasts of 25mm x 4mm fi, 25cm long, 6 nos in each chowkhat, necessary lugs, 3 nos 100 mm ms butt hinges medium weight, cold rolled, welded for each shutters of frame, lock strike plate, including sanding, tarring backs of chowkhats, pcc 1:3:6 type c 0filling in frame and for holdfast, 2 nos 12 mm dia ms tie bars at the bottom of frame and one shop coat of red oxide primer etc complete all as specified and as directed. 65 supplyand fixing of factory made 35 mm thick, second class hard wood rail and style, plain framed, panelled shutter ( two panel ) with lock rail and panel of 9 mm b.w.p commercial ply or 12 mm veneered particle board with commrcial veneering on both faces ace, size of rails and stiles asper is 1003 ( part i ) kiln seasoned and chemical pressure treated complete all as specified and directed. 66 supply and fixing of iind class ( hollock ) factory made 35mm thick glazed skelton door shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass / gauge etc. with sizes of members of shutters as specified in para 8.24 ( a ) of ssr 2009 ( part i ) , complete all as specified and directed. 67 supply and fixing factory of made pvc hollow door frame of size 50mm x 47mm with wall thickness of 5 mm made out of extended 5 mm rigid pvc foam sheet cut at corner and jointed with 02 nos, 150 mm long brackets of size 15 mm x 15 mm mild steel square tubes 19 gauge including vertical door profiles reinforced with 19 mm x 19 mm steel square tube of 19 gauge ( epdm ) rubber gasket weather seal provided through out the frame and fixed to wall with 65 / 100 mm long mild steel screws through the frame by using pvc fasteners ( minimum of 04 nos of screws to be provided for each vertical numbers & minimum 02 nos for horizontal member ) complete all as specified and directed. 68 supply andfixing factory made solid pvc moulded door shutter, 28 to 30 mm thick ( stiles ) with 2, 4 or 6 raised panel design with 2 mm thick moulded pvc sheet on the front face & 2 mm plain colour pvc sheet on back face includingfixing in frame at site with 03 nos ss hinges, 02 nos aluminium tower bolt 150 mm, 02 nos aluminium handle 150 mm for each shutter all as per specification & drawing complete all as specified and directed. 69 supply and fixing in repair of steel window box type using erw hollow p section comprising double frame for and including gauged and glazed skelton shutter 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs etc. all as shown on drawing no. td 219 ( c ) sheet 1 / 3 to 3 / 3 and td 220 ( c ) sheet 1 / 3 to 3 / 3 as applicable including pcc ( c o , 1:3:6 using 12.5 graded agg ) bed blocks for hold fasts and one shop coat of red oxide primer etc complete all as specified and directed.note: ( i ) for the purpose of measurement & payment double shutter with frame shall be considered as one unit. ( ii ) unit rate quoted against this item shall also include the iron mongery , grills 10mm square bars. ( iii ) only glazing, wire mesh & painting grill shall be measured & paid for separately ) 70 supply and fixingin repairs of mild steel ventilator of section framed fixed type and fixed wire mesh with flat bends 10 mm x 3 mm with nuts / bolts complete including fixing lugs, necessary pcc 1:3:6 type c 1 for filling bed blocks of hold fasts / lugs, etc complete all as specified and directed. 71 supply and fixing of mild steel pressed handle, 150mm long, oval type, stove enameled black, complete all as specified and directed. 72 supply and fixing of mild steel barrel tower bolt stove enamelled black with bright bolt 200mm long complete all as specified and directed. 73 supply and fixing of250 mm long mild steel sliding door bolts , plate type, stove enamelled black, with bright bolt not less than 12mm with and including a minimum of 6 bolts and nuts , four on bolt plate and two on staple plate complete all as specified and directed. 74 returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in soil complete all as specified and directed. 75 removing surplus excavated material ( soil ) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed. 76 material and labour for pcc 1:3:6 type c 2 using 40mm graded mechanically crushed stone aggregate as in foundation filling, mass concrete, sub base etc. complete all as specified and directed 77 material and labour for plain cement concrete 1:2:4 type b 1 ( using 20mm graded mechanically crushed stone aggregate ) as in surface channels and drains, complete all as specified and as directed. 78 material and labour for pcc 1:2:4 type b 1 ( using 20 mm graded mechanically crushed stone aggregate ) ascopings, bed plates, kerbs, and other bands and the like, finished the surface fair andeven, including necessary form work etc including demolition of existing cement concrete of any description and in any position complete all as specified and directed. 79 material and labour for providing and laying of precast cement concrete solid concrete block, type b 1, 1:2:4 ( using 20mm graded stone aggreagate ) confirming to is 2185 ( part i ) 2005 of 30 cm high, 10 cm thick and of suitable width including chamfers, weatherings, throating etc as in kerb continuous edging jointed in cement mortar 1:4 and struck flush pointing as the work proceeds and finishing with neat cement flush joint etc complete all as specified and directed. 80 dismantling / taking down carefully aluminium / copper point wiring ( light, fan, socket or power ) complete, including fixtures and fittings such as switches, ceiling roses, pendants, regulators , sockets, light fittings etc., removing materials to stores for keeping in safe custody for taking credit and making good the disturbed surfaces of wall, floors, ceiling etc to match with the existing surfaces with matching obd / white wash / distemper complete all as specified and as directed. 81 material and labour for concealed point wiring with 1.50 sqmm single core pvc insulated, unsheathed cable frlsh, 1100 volt grade with multi stranded copper conductor drawn through and including medium grade, isi marked, pvc conduit not less than 25 mm dia with frlsh accessories, concealed and including provision of 1.50 sqmm single core pvc insulated, unsheathed cable frlsh 1100 volt grade with multi stranded copper conductorgreen colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to is 5139 ( pt i ) of 1969 and is:14772 2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer bothinternally and externally including provision of new 3 mm thick plastic laminated sheet top cover extended up to 25 mm over sunken box for housing the switches , socket outlets, fan regulators etc. with brass screws and brass washersand making goodthe disturbed surfaces as per existing for one light / fan point / bell point controlled by one switch complete all as specified and directed. notes : ( i ) the quoted rates shall be deemed to be inclusive for cutting chases by chase cutter in wall / pillars / columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. the portion of point wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using necessary accessories / fittings. ( ii ) point wiring & earth wire shall be connected to each & every flush / sunken box. ( iii ) all screws, fasteners, bolts, nuts & washer shall be cadmium plated & the cost of which is deemed to be included in the quoted unit rates. 82 description all as per item no 81.00 above but for socket out let point 5 amps on same board complete all as specified and directed. 83 description all as per item no 81.00 above but for socket out let point 5 amps on independentboard complete all as specified and directed. 84 description all as per srl item no 81.00 above but point wiring for one socket out let 15&5 amps ( independent ) controlled by one switchwith using 2.5 sq mm ( nominal area ) stranded copper conductor complete all as specified and directed. 85 supply and fixing of switch piano 6 amps, flush type, single pole, one way, 230 volt , ac supply, isi marked, complete all as specified and directed. 86 supply and fixing of switch piano 15 amps flush type one way 230 volts, 50 hz, ac supply, isi marked, complete all as specified and directed. 87 supply and fixingsocket outlet 3 pin 5 amps, 230 volts flush type , isi marked, complete all as specified and directed. 88 supply and fixing of socket outlet 2 in 1, 6 / 16 amps, 5 pin 230 volt flush type, isi marked complete all as specified and directed. 89 supply and fixing of ceiling rose surface bakelite 65x50mm, 3 terminal complete all as specified and directed. 90 supply and fixing offan regulator electronic step type , 230 volts, ac supply, suitable for ceiling fan any type / make / sweep, complete all as specified and directed. 91 supply and fixing lamp holder, pvc / polycarbonate type with back plate suitable for batten fittings, complete all as specified. 92 supply and fixing of led lamp 9 watt suitable for batten holder complete all as specified and directed 93 supply and fixing of double stiff pendants, comprising of galvanised steel or chromium plated brass bell mouth connectors 2 nos. with back plate and 2×1.50 metre long parallel 20mm dia galvanised or stove enamelled screwed steel conduit with two check nuts for fixing tube light fitting and upto 1.5 metre long twin core 0.5 sq. mm copper conductor flexible wire / cable including disconnecting and taking down old existing light fitting of any description and in any position complete all as specified and directed. 94 supply and fixing of industrial box channel for fixing of led tube rod, in crca body suitable for 2x18 / 20 watt led tube, high efficient, ac 220 240 volts, 50 hz and connecting with copper conductor flexible cable of size 0.50 sqmm from ceiling rose to connector of the light including disconnecting and taking down old existing light fitting of any description and in any position complete all as specified and directed. note : ( i ) tube rod shall be measured and paid for separately. ( ii ) channel must be get approved from engr in charge to check fesibilty i.e. one end contact or two end contact. 95 supply and fixing of channel for fixing of led tube rod, in crca body suitable for 18 / 20 watt led tube, high efficient, ac 220 240 volts, 50 hz and connecting with copper conductor flexible cable of size 0.50 sqmm from ceiling rose to connector of the light including disconnecting and taking down old existing light fitting of any description and in any position complete all as specified and directed. note : ( i ) tube rod shall be measured and paid for separately. ( ii ) channel must be get approved from engr in charge to check fesibilty i.e. one end contact or two end contact. 96 supply and fixing of 18 w / 20w polycarbonate led tube light, environment friendly, high efficient, t8 with aluminium extrusion heat sink for optimum performance with high luminous efficiency and easy and taking down existing tube light and removal complete all as specified and directed. note: tube rod must be get approved from engineer in charge to check fesibilty i.e. one end contact or two end contact for fixing in existing led fittings. 97 supply and fixing ofbulk head light fitting, 15 watt, energy efficient withlamp 15 watt with provision of 2 / 3 core pvc copper conductor cable 0.5 sqmm size from ceiling rose to light fitting completeincluding disconnecting and taking down old existing light fitting of any description and in any position complete all as specified and directed. 98 supply and fixing in repair bracket for security light made up of 25mm dia, 0.9 metre long gi pipe, light grade, bent to required length, fixed to wall with two clamps made of 20 x 3 mm mild steel flat minimum 15cm long, 4 nos 8mm dia bolts with nuts complete all as specified and directed. 99 supply and fixing led security light luminaire 50 watt , pressure die cast aluminum housing, toughened heat resistant glass, ip65 protection, better optics for uniform distribution with multiplte leds not less than 2 w each and having optical grade polycarbonate lens with all accessories internally pre wired and including connecting up with two core 1.5 sq mmcopper conductor cable from connector to ceiling rose to connection of light including disconnecting and taking down oldunserviceable security light fitting of any description and in any position complete all as specified and directed. 100 supply and fixing led high efficient bay light 50 watt, die cast aluminum housing, toughened heat resistant glass, ip66 protection, better optics for uniform distribution with all accessories internally pre wired and including connecting up with two core 1.5 sq mmcopper conductor cable from connector to ceiling rose to connection of light including disconnecting and taking down oldunserviceable security light fitting of any description and in any position complete all as specified and directed. 101 supply and fixing of sheet metal enclosures vertical distribution board vtpn, ( mccb db ) 4 ways, double door, 415 volts with 200 amps rated bus bar ip 54 protection, with shrouded neutral bar and insulated bus bar and earth link, with and includingmccb 4 pole thermal release type, 100 amps, 16 kaas incomer and mcbsas out going complete with making suitable size of ms cabinet 2 mm thick dully grouted on the wall ( flush ) with opening arrangement including making connections with suitable size of lugs / thimbles / glands and making good the disturbed surface matching with existing surface including taking down existing unserviciable mccb / dbs including mcbs complete all as specified and directed. 102 supply, installation, testingofspn distibution board 8 way, double door , ip 43, as per is 8623including 200 amps fully insulated copper bus bar, insulated neutral bar, earth bar, door earthing, reversible doors, pan assembly for easy installation and also incoming and outgoing connections with suitable size of lugs / thimblesincluding taking down existing unserviciable mcb / dbs including mcbs complete all as specified and directed. 103 supply, installation, testingofspn distibution board 4 way, double door , ip 43, as per is 8623including 200 amps fully insulated copper bus bar, insulated neutral bar, earth bar, door earthing, reversible doors, pan assembly for easy installation and also incoming and outgoing connections with suitable size of lugs / thimblesincluding taking down existing unserviciable mcb / dbs including mcbs complete all as specified and directed. 104 supply and fixing of mcb single pole, 240 volts, 50hz , breaking capacity 10ka, b curve 6 to 32 amps, including connection with suitable size copper lugs complete all as specified and directed. 105 supply and fixing of mcb single pole, 240 volts, 50hz , breaking capacity 10ka, b curve 40 to 63 amps, including connection with suitable size copper lugs complete all as specified and directed. 106 supply and fixing of mcb single pole and neutral, 240 volts, 50hz , breaking capacity 10ka, b curve 40 to 63 amps, including connection with suitable size copper lugs complete all as specified and directed. 107 material and labour for concealed sub main wiring with two single core frlsh pvcinsulatedunsheathed copper conductor cable 2.5 sqmm drawnin and including rigid non metallic pvc medium grade 25 mm dia concealed conduit with accessories onwall or ceiling withone additional pvc insulated , strandedcopper conductor frlshof 2.5 sqmm, green colourfor earthcontinuity conductor including taking down old unserviceable sub main wiringand making good the disturbed surface complete all as specified and directed.note : 3 run of cable and 1 run ofconduit shall be measured as 1 unit. ( ii ) the quoted rates shall be deemed to be inclusive for cutting chasesin wall / pillars / columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. the portion of sub main wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using necessary aceessories / fittings. 108 material and labour for concealed sub main wiring with two single core frlsh pvcinsulatedunsheathed copper conductor cable 4.00 sqmm drawnin and including rigid non metallic pvc medium grade 25 mm dia concealed conduit with accessories onwall or ceiling withone additional pvc insulated , strandedcopper conductor frlshof 4.00 sqmm, green colourfor earthcontinuity conductor including taking down old unserviceable sub main wiringand making good the disturbed surface complete all as specified and directed.note : 3 run of cable and 1 run ofconduit shall be measured as 1 unit. ( ii ) the quoted rates shall be deemed to be inclusive for cutting chasesin wall / pillars / columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. the portion of sub main wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using necessary aceessories / fittings. 109 material and labour for concealed sub main wiring with two single core frlsh pvcinsulatedunsheathed copper conductor cable 6.00 sqmm drawnin and including rigid non metallic pvc medium grade 25 mm dia concealed conduit with accessories onwall or ceiling withone additional pvc insulated , strandedcopper conductor frlshof 6.00 sqmm, green colourfor earthcontinuity conductor including taking down old unserviceable sub main wiringand making good the disturbed surface complete all as specified and directed.note : 3 run of cable and 1 run ofconduit shall be measured as 1 unit. ( ii ) the quoted rates shall be deemed to be inclusive for cutting chasesin wall / pillars / columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. the portion of sub main wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using necessary aceessories / fittings. 110 taking out of unserviceable earthing and material and labour for earthing and material & labour for earthing with galvanised steel earth plate electrode 60cmx 60cm x 6.0 mm thick buried directly in ground vertically at a depth not less than 2.25metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, earth plate surrounded from all sides by 15cm thick packed layer ofcharcoal dust and common salt filling in alternate layers and electrode connections by usinggalvanised iron wire 4mmas earthing lead ( upto terminal point ) by means ofbolts, nuts, check nuts and washers made of galvanised iron and thimbles and protected by light grade 15 mm diagi pipe connected to main switch board or main control board and gi pipe medium grade 20mm bore for watering and including funnel , wire mesh, 50 mm thick precast rcc 1:2:4 type b1using 20 mm graded stone aggregate , reinforced with 8 mm dia dedormed / tmt bars 3 nos both way 12 mm dia round bar handle and pcc chamber pit with pcc ( 1:3:6 ) type c 2 using 40mm graded stone aggregate, including excavation and earth work in any type ofsoil , returning , filling in approved soil and disposal of surplus soil to a distance not exceeding 50m all as specified and shown in electrical plate no 3 ofssr 2009 ( part i ) complete all as specified and as directed. note : ( i ) earth lead wire and its protection pipe upto and including 7.50 mtr only from top of earth electrode are included under this item. ( ii ) on testing if the earth resistance is not obtained within permissible limit, earthing will be re done at no extra cost , till the desired earth resistance is obtained. ( iii ) any joint in earth lead from earth electrode to test point shall not be allowed / permitted. 111 supply, laying and testing of cable xlpe insulated, armoured heavy duty electric cable with standred aluminium conductor, 1100 volts grade, cross sectional area of size 25 sqmm 4 core including dismantling existing any type and any size cable complete all as specified and directed. 112 supply, laying and testing of cable xlpe insulated, armoured heavy duty electric cable with standred aluminium conductor, 1100 volts grade, cross sectional area of size 10 sqmm 2 core including dismantling existing any type and any size cable complete all as specified and directed. 113 supply and fixing in repair of gi protection pipe of 40mmdia light grade for cable protection including all fittings laid in trenches or fixed on pole, complete all as specified and as directed. 114 material and labour for supply and filling sand with clean dry fine sand unwashed including gently punning around cables in trenches for cable protection complete all as specified and directed. note: punned thickness shall be measurement & paid. 115 material and labour for brick protection covers over cable using sub class b old size brick laid along length of cable complete all as specified and directed. 116 supply and fixing 1100 volts grade heavy duty cable pvc insulated aluminium conductor, served with inner sheathing of pvc tape and overall pvc sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular of size 16sqmm including all incoming and outgoing connection with proper size of thimble including disconnecting and taking down existing cables etc. complete all as directed and specified. 117 supply and fixing in repair of house service bracket ( hook type ) complete with 3.0 m long gi pipe 40mm dia medium grade pipe, two 90 degree bends. ms hook, stay or guy including fixing clamps etc complete all as specified and directed. 118 note: amount of credit ofrs. 74, 062.00 for retrieved materials is mentioned in schedule of credit page no 19 & 20 of tender documents in pdf form which will be deducted offline while acceptance of tender....

Public Health Engineering Department - Haryana

34991202 annual maintenance water supply scheme narnaul town, district mohindergarh. taking out all layer of filter media and placing the same after washing, taking out of rcc bed plates and placing the same after washing of drains & plates, placing of top layer filter media and rcc bed plates in lieu of damaged plates in 3 nos. filters beds of wtp unit at existing 2nd canal based water works nasibpur in narnaul town and all other works contingent thereto”...

Public Health Engineering Department - Haryana

33665983 tender for outsourcing of works/ hiring of jcb hiring of jcb per hour / ajitpura hrs. 2 2 pipes / pvc pipe 6kgf 150mm / ajitpura mtrs. 4 3 cid joints/ c i d joints class 20 cid joint 6` / ajitpura nos. 2 4 miscellaneous items/ misc. items cement / ajitpura nos. 1 5 miscellaneous items/ misc. items curesre. / per ft. nos. 10 6 miscellaneous items/ misc. items filter bed plate. / water works. nos. 20 7 miscellaneous items/ misc. items fitter / ajitpura nos. 1 8 miscellaneous items/ misc. items labour / ajitpura nos. 4 9 miscellaneous items/ misc. items mistri / ajitpura nos. 2...

Public Health Engineering Department - Haryana

32279314 bhuna town annual maintenance water supply scheme bhuna town tehsil & distt. fatehabad. taking out all five layer of 5 nos. filter beds of size = 33 0 diarelaying in proper gradient after washing, screening and cleaning and taking out and relaying of filter bed plates washing corss drains and central drains with brush at water supply scheme bhuna town and all other works contingent thereto => limited...

Public Health Engineering Department - Haryana

32199501 recalled rohtak mtc ws scheme bohar providing and placing of horizontal layer filter media of top layer and washing of second layer, third layer, forth layer and bottom layer and bed plates of 4 no filter bed...

Public Health Engineering Department - Haryana

32016137 annual maintenance of water supply scheme rohtak towndistt. rohtak providing and placing of horizontal layer filter media of top layer and washing of second layer, third layer, forth layer and bottom layer and bed plates of 4 no filter bed at bohar bhopanand all other works contingent thereto....

Department Of Technical Education - Haryana

31324177 supply of tool and equipment 1 welding helmet fiber 2 welding hand shield fiber 3 chipping hammer 4 chisel cold 5 centre punch 6 dividers 7 stainless steel rule 8 scriber 9 flat tongs 10 hack saw frame 11 file half round 12 file flat 13 hammer ball pane 14 tip cleaner 15 try square 16 spindle key 17 screw driver 18 number punch 19 letter punch 20 magnifying glass 21 universal weld measuring gauge 22 earth clamp 23 spanner d.e. 24 c clamps 25 hammer sledge 26 s.s tape 27 electrode holder 28 h.p. welding torch 29 oxygen gas pressure 30 acetylene gas pressure 31 co2 gas pressure regulator 32 argon gas pressure regulator 33 metal rack 34 first aid box 35 steel lockers 36 steel almirah / cupboard 37 black board and easel with stand 38 flash back arrester ( torch mounted ) 39 flash back arrester ( cylinder mounted ) 40 welding transformer 41 welding transformer ( or ) inverter based welding machine 42 d.c arc welding rectifiers set with all accessories 43 gmaw welding machine 44 ac / dc gtaw welding machine 45 air plasma cutting equipment 46 air compressor suitable for above air plasma cutting system. 47 auto darkening welding helmet 48 spot welding machine 49 portable gas cutting machine 50 pedestal grinder fitted with coarse and medium grain size grinding wheels 51 bench grinder fitted with fine grain size silicon carbide green grinding wheel 52 ag 4 grinder 53 suitable gas welding table 54 suitable arc welding table 55 trolley for cylinder ( h.p. unit ) 56 hand shearing machine capacity 57 power saw machine 58 portable drilling machine 59 oven, electrode drying 60 work bench 61 oxy acetylene gas cutting blow pipe 62 oxygen, acetylene cylinders ** 63 co2 cylinder ** 64 argon gas cylinder ** 65 anvil 12 sq. inches working area with stand 66 swage block 67 die penetrant testing kit 68 magnetic particle testing kit # 69 fire extinguishers ( foam type and co2 type ) 70 fire buckets with stand 71 portable abrasive cut off machine 72 suitable gas cutting table 73 welding simulators for smaw / gtaw / gmaw 74 leather hand gloves 75 cotton hand gloves 76 leather apron leather 77 s.s wire brush 78 leather hand sleeves 79 safety boots for welders 80 leg guards leather 81 rubber hose clips 82 rubber hose oxygen 83 rubber hose acetylene 84 arc welding cables multi cored copper 85 arc welding single coloured glasses 86 arc welding plain glass 87 gas welding goggles 88 safety goggles plain 89 spark lighter 90 ag 4 grinding wheels 91 instructor’s table and chair ( steel ) 92 students chairs with writing pads 93 white board 94 instructors lap top with latest ( vista & above ) configuration pre loaded with operating system and ms office package. 95 lcd projector with screen. 96 welding process, inspection & codes dvd / cds 97 drawing board 98 models : solid & cut section 99 table for trainees 100 stool for trainees 101 cupboard ( big ) 102 white board 103 trainer’s table 104 trainer’s chair 105 measuring steel tape 106 combination plier insulated 107 screwdriver insulated 108 screwdriver insulated 109 electrician screwdriver thin stem insulated handle 110 heavy duty screwdriver insulated 111 electrician screwdriver thin stem insulated handle 112 punch centre 113 knife double bladed electrician 114 neon tester 115 steel rule graduated both in metric and english unit 116 hammer, cross peen with handle 117 hammer, ball peen with handle 118 pincer 119 c clamp 120 spanner adjustable drop forged, ss 121 blow lamp brass 122 chisel cold 123 chisel firmer with wooden handle 124 allen key alloy steel 125 grease gun 126 bradawl 127 pully puller with 3 legs 128 bearing puller ( inside and outside ) 129 pipe vice cast iron with hardened jaw open type 130 scissors blade, ss 131 scissors blade, ss 132 crimping tool 133 134 wire cutter and stripper 135 mallet hard wood 136 hammer extractor type 137 hacksaw frame 138 try square 139 outside calliper 140 inside calliper 141 divider 142 pliers long nose insulated 143 pliers flat nose insulated 144 pliers round nose insulated 145 tweezers 146 snip straight and bent heavy duty 147 d.e. metric spanner double ended 148 drill hand brace 149 drill s.s. twist block 150 plane cutters 151 smoothing cutters 152 gauge, wire imperial stainlees steel marked in swg & mm 153 file flat 154 file half round 155 file round 156 file flat rough 157 file flat bastard 158 file flat smooth 159 file rasp, half round 160 copper bit soldering iron. 161 de soldering gun 162 hand vice 163 table vice 164 oil can 165 contactor & auxiliary contacts 166 167 contactor & auxiliary contacts. 168 limit switch 169 rotary switch 170 relay a. cut out relays b. reverse current c. over current d. under voltage 171 pin type, shackle type, egg type & suspension type insulators including hardware fitting 172 hydrometer 173 hand drill machine 174 portable electric drill machine 175 load bank ( lamp / heater type ) 176 brake test arrangement with two spring balance rating 177 laboratory type induction coil 178 out side micrometer 179 thermometer digital 180 series test lamp 181 knife switch dpdt fitted with fuse terminals 182 knife switch tpdt fitted with fuse terminals 183 miniature breaker 184 earth plate 185 earth electrode 186 mccb 187 elcb and rccb 188 fuses 189 rheostat ( sliding type ) 190 191 capacitors 192 various electronic components 193 various lamps 194 plug socket piano switch lamp holder 195 cables: twisted pair non metallic sheathed cable underground feeder cable ribbon cable metallic sheathed cable multi conductor cable coaxial cable direct buried cable 196 bus bar with brackets 197 rubber mat 198 electrician helmet 199 rcc pole with accessories ( ms angle iron, ‘c’ clamp, stay insulator etc. ) and materials 200 safety belt 201 ohm meter; series type & shunt type, portable box type 202 digital multi meter 203 a.c. voltmeter m.i. analog, portable box type housed in bakelite case 204 milli voltmeter centre zero analog, portable box type housed in bakelite case 205 ammeter mc analog, portable box type housed in bakelite case 206 ac ammeter mi, analog, portable box type housed in bakelite case 207 kilo wattmeter analog 208 digital wattmeter 209 a.c. energy meter 210 a.c. energy meter 211 power factor meter digital 212 frequency meter 213 magnetic flux meter 214 lux meter 215 tachometer 216 tachometer 217 tong tester / clamp meter 218 megger 219 3 point d.c. starter 220 4 point d.c. starter 221 wheat stone bridge with galvanometer and battery 222 single phase variable auto transformer 223 phase sequence indicator 224 growler 225 ac starters: a. resistance type starter b. direct online starter c. star delta starter manual d. star delta starter – semi automatic e. star delta starter – fully automatic f. star delta starter soft starter g. auto transformer type 226 oscilloscope dual trace 227 function generator 228 soldering iron 229 temperature controlled soldering iron 230 discrete component trainer 231 linear i.c. trainer 232 digital i.c. trainer 233 domestic appliances – 234 a. electric induction plate 235 b. electric kettle 236 c. electric iron 237 d. immersion heater 238 e. a.c. ceiling fan and ac table fan 239 f. geyser ( storage type ) 240 g. mixture & grinder 241 h. washing machine semi automatic 242 i. motor pump set 243 oil testing kit 244 inverter with battery 245 voltage stabilizer 246 dc power supply 247 battery charger 248 current transformer 249 potential transformer 250 solar panel with battery 251 pentium iv computer or latest 252 ink jet / laser printer 253 d.c. shunt generator with control panel 254 motor generator ( ac to dc ) 255 d.c. compound generator with control panel including fitted rheostat, voltmeter, ammeter and breaker 256 dc series motor coupled with spring balance load 257 dc shunt motor 258 dc compound motor with starter and switch 259 motor generator ( dc to ac ) set consisting of shunt motor with starting compensator and switch directly coupled to ac generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. set complete with cast iron bed plate, fixing bolts, foundation bolts and flexible coupling. 260 ac squirrel cage motor with star delta starter and triple pole iron clad switch fuse with mechanical load. 261 ac phase wound slip ring motor with starter switch 262 universal motor with starter / switch 263 synchronous motor with accessories like starter, excitation arrangements. 264 thyristor / igbt controlled d.c. motor drive with tacho generator feedback arrangement 265 thyristor / igbt controlled a.c. motor drive with 266 single phase transformer, core type, air cooled 267 three phase transformer, shell type oil cooled with delta / star 268 electrical machine trainer – 269 diesel generator set with changeover switch, over current breaker and water / air cooled with armature, star delta connections ac 3 phase 270 used dc generators series, shunt and compound type for overhauling practice 271 pillar electric drill machine motorized 272 motorised bench grinder 273 a.c. series type motor 274 single phase capacitor motor with starter switch 275 manual motor coil winding machine 276 ceiling fan coil winding machine 277 primary current injection set 278 stepper motor with digital controller 279 shaded pole motor 280 working bench 281 wiring board 282 instructor’s table 283 instructor’s chair 284 metal rack 285 lockers with drawers 286 almirah 287 black board / white board 288 fire extinguisher co2 289 fire buckets...

Public Health Engineering Department - Haryana

31117677 kumbha – providing functional house hold tap connection and upgradation and replacing damaged distribution system taking out of new filter media all layers of filter media, beds plates & placing the same after washing 3 nos. filter beds at water works kumbha and all other works contingent thereto...

Public Health Engineering Department - Haryana

27925435 taking out all layer of filter media and placing the same after washing , taking out of rcc bed plates and placing the same after washing of drains and plates , placing of top layer filter media and rcc bed plates in lieu of damaged plates in 8 nos . fi...

Public Health Engineering Department - Haryana

27795154 taking out all layer of filter media and placing the same after washing , taking out of rcc bed plates and placing the same after washing of drains and plates , placing of top layer filter media and rcc bed plates in lieu of damaged plates in 8 nos . fi...

Public Health Engineering Department - Haryana

27729979 annual maintenance . water supply scheme narnaul town , district mohindergarh . repairing of existing 4 . 50 mld wtp , taking out of all layer of filter media , rcc bed plates and placing the same after washing of drains and filters beds , placing of top layer filter . . . repairing of existing 4 . 50 mld wtp , taking out of all layer of filter media , rcc bed plates and placing the same after washing of drains and filters beds , placing of top layer filter media and new rcc bed plates , 1 no . blower set including electric m...

Public Health Engineering Department - Haryana

27626868 annual maintenance water supply scheme 121 nos. census villages, district mohindergarh. taking out all layer of filter media and placing the same after washing, taking out of rcc bed plates and placing the same after washing of drains & plates, placing of top layer filter media and rcc bed plates in lieu of damaged plates in 8 nos. filters beds of 2 nos. wtp unit having capacity 7.00 & 7.25 mld at existing canal based water works lehroda and all other works conting thereto...

Public Health Engineering Department - Haryana

26598732 annual maintenancer water supply scheme 121 nos . census villages , district mohindergarh . taking out all layer of filter media and placing the same after washing , taking out of rcc bed plates and placing the same after washing of drains and plates , placing of top...

Public Health Engineering Department - Haryana

26078097 annual maintenance water supply scheme 121 nos . census villages , district mohindergarh . taking out all layer of filter media and placing the same after washing , taking out of rcc bed plates and placing the same after washing of drains and plates , placing of top...

Public Health Engineering Department - Haryana

25032258 annual maintenance work for water supply. 1 outsourcing of works/ job work for filter media washing etc. taking out rcc bed plates and placing outside /taking out rcc bed plate from filter bed and replacing of rcc bed plate after cleaning of drains / at water works dharoli bed no.2 2 outsourcing of works/ job work for filter media washing etc. taking out top layer to bottom layer of filter media from filter beds /taking out top layer to bottom layer / at water works dharoli bed no.2...

Department Of Technical Education - Haryana

24076650 supply of tools and equipments 1 connecting screwdriver 100 mm 2 neon tester 500 v. 3 screw driver set ( set of 5 ) 4 insulated combination pliers 150 mm 5 insulated side cutting pliers 150 mm 6 long nose pliers 150 mm 7 soldering iron 25 w. 240 v. 8 electrician knife 9 tweezers 100mm 10 digital multimeter 11 soldering iron changeable bits 15 w 12 de soldering pump 13 soldering iron 25w 14 magneto spanner set 15 steel rule 150mm 16 tubular box spanner ( set of 6nos ) 17 continuity tester 18 cold chisel 20mm 19 scissors 200mm 20 handsaw 450mm 21 server computer 22 laptop, notebook for demonstration 23 laptop, notebook 24 intel mobile desktop based pc with lcd monitor 25 network printer 26 5kva online ups 27 lcd / dlp projector 28 computer spares: 29 motherboards ( of different make ) 30 processors ( of different make ) 31 hard disk ( 500 gb or better ) 32 optical drives 33 external hard disk 34 digital multimeters 35 external hard disk 36 digital camera 37 hd display 38 network storage 39 game video card 40 web cam 41 surround sound speakers 42 laptop kits 43 laptop spares: 44 smps trainer kit 45 ups trainer kit 46 power electronics trainer kit 47 post error debugging card 48 smps tester 49 pci slot testing tool 50 windows server operating system 51 windows operating system 52 linux operating system 53 network management software 54 ms office 55 anti virus software 56 air conditioners ( optional ) 57 scanner 58 modem 59 fire fighting equipments 60 hardware and network trainer kit 61 wireless network adapter 62 network training system 63 lan protocol simulation and analyser software 64 network and internet security trainer 65 lan cable tester 66 network cables – utp 67 network cables – coaxial, flat, ribbon 68 connectors for cables 69 24 port utp jack panel 70 sc pigtails 71 rj 45 connector 72 multimeter 73 crimping tools 74 nvr 75 poe adapters kit 76 network camera ( outdoor / indoor ) 77 measuring tape 78 seam ripper 79 thimble 80 tailors card scale triangular 81 tailors square 82 french curve 83 thread cutter 84 scale plastic 85 scissors 86 pinking shears 87 leg shaper 88 garment hangers 89 screw driver set 90 table sharpener 91 pressing table 92 blanket for padding of pressing table 93 rubber mat 94 sprayer 95 waste bin big / small 96 pattern punch 97 pattern notcher 98 pattern hanging stand 99 water tub 100 stand for hanging dresses 101 trial room with arrangements of hanging dressestrial room with arrangements of hanging dressestrial room with arrangements of hanging dressestrial room with arrangements of hanging dressestrial room with arrangements of hanging dressestrial room with arrangements of hanging dressestrial room with arrangements of hanging dressestrial room with arrangements of hanging dressestrial room with arrangements of hanging dresses 102 electric automatic steam press 103 sewing machine 104 over lock machine 3 thread 105 zigzag multi purpose machine 106 double needle machine 107 button hole machine 108 button sewing machine 109 machine attachments 110 chairs with low back rest or stools for the machineschairs with low back rest or stools for the machineschairs with low back rest or stools for the machineschairs with low back rest or stools for the machineschairs with low back rest or stools for the machineschairs with low back rest or stools for the machineschairs with low back rest or stools for the machineschairs with low back rest or stools for the machineschairs with low back rest or stools for the machines 111 drafting table 112 display board covered with glass or acrylic sheetdisplay board covered with glass or acrylic sheetdisplay board covered with glass or acrylic sheetdisplay board covered with glass or acrylic sheetdisplay board covered with glass or acrylic sheetdisplay board covered with glass or acrylic sheetdisplay board covered with glass or acrylic sheetdisplay board covered with glass or acrylic sheet 113 instructor table 114 instructor chair 115 steel almirah 116 pigeon hole almirah 117 locks for above pigeon hole 118 wall clock 119 calculator desk type 120 white board with accessories 121 dummy lady, men, kid 122 computer system 123 printer 124 work station with chair 125 single desks for trainees with arrangements of keeping books etc.single desks for trainees with arrangements of keeping books etc.single desks for trainees with arrangements of keeping books etc.single desks for trainees with arrangements of keeping books etc.single desks for trainees with arrangements of keeping books etc.single desks for trainees with arrangements of keeping books etc.single desks for trainees with arrangements of keeping books etc.single desks for trainees with arrangements of keeping books etc. 126 revolving chairs without arms 127 faculty table & chair set 128 computer set with ups & multimedia projectorcomputer set with ups & multimedia projectorcomputer set with ups & multimedia projectorcomputer set with ups & multimedia projectorcomputer set with ups & multimedia projectorcomputer set with ups & multimedia projectorcomputer set with ups & multimedia projector 129 white magnetic board with felt board & accessorieswhite magnetic board with felt board & accessorieswhite magnetic board with felt board & accessorieswhite magnetic board with felt board & accessorieswhite magnetic board with felt board & accessorieswhite magnetic board with felt board & accessorieswhite magnetic board with felt board & accessories 130 display board 131 storage almirah 132 book shelf 133 a / c unit split type 134 measuring steel tape 135 combination plier insulated 136 screwdriver insulated 137 screwdriver insulated 138 electrician screwdriver thin stem insulated handel 139 heavy duty screwdriver insulated 140 electrician screwdriver thin stem insulated handel 141 punch center 142 knife double blades electrician 143 neon tester 144 steel rule graduated both in matric and english unit 145 hammer , cross peen with handel 146 scissors blade, ss 147 crimping tool 148 wire cuuter and stripper 149 smoothing cutter 150 guage wore imperial stainlees steel marked in swg&mm 151 file flat 152 contactor&auxilliary contacts 153 limit switch 154 rotary switch 155 under voltage 156 pin type shackle type egg type&suspension type insulators including hardware fittinf 157 hand drill machine 158 portable electric drill machine 159 load bank ( lamp / heater type ) 160 earth plate 161 earth electroad 162 capacitors 163 rubber mat 164 electrician halmet 165 rcc pole with accessories ( ms angle ironc clamp stay insulator etc. ) and , aterials 166 safety belt 167 ohm meter ;series type&shunt type portable box type 168 digital multi meter 169 digital wattmeter 170 a.c. energy meter 171 tachometer 172 tong tester / clamp meter 173 megger 174 wheat stone bridge with galvanometer 175 phase sequence indicator 176 a. resistance type starter, ( b ) direct online starter ( e ) star delta starter fully automatic ( f ) star delta starter soft starter 177 temperature controlled soldering iron 178 discrete component trainer 179 ( g ) mixture& grinder ( h ) washing machine semi automatic 180 soler panel with battery 181 ink jet / laser printer 182 d.c compound generator with control panel including fitted rheostate , voltmeter ammeter and breaker 183 motor generator ( dctoac ) set consisting of shunt motor with starting coupled to ac generator with exciter and switch board mounted with regilator , breack ammeter voltmeter frequency meter knife blade switch and fuses etc, set complete with cast iron bed plate fixing bolts foundation bolts and flexible coupling. 184 universal motor with starter / switch 185 synchronous moptor with accessories like starter excitation arrangements. 186 thyristor / igbt controlled d, c motor drive with tacho generator feedback arrangement 187 thyristor / igbt controlled a.c motor drive with 188 diesel generator set with changeover switch over current breaker and water / air cooled with aemature star delta connection ac 3 phase 189 manual motor coil winding machine 190 primary current injection set 191 shaded pole motor 192 welding helmet fiber 193 welding hand shield fiber 194 chipping hammer 195 chisel cold 196 centre punch 197 dividers 198 stainless steel rule 199 scriber 200 flat tongs 201 hack saw frame 202 file half round 203 file flat 204 hammer ball pane 205 tip cleaner 206 try square 207 number punch 208 co2 gas pressure regulator 209 argon gas pressure regulator 210 black board and easel with stand 211 air plasma cutting equipment 212 air compressor suitable for above air plasma cutting system 213 ag 4 grinder 214 oxygen acetylene cylinders** 215 welding simulators for smaw / gtaw / gmaw 216 leather hand gloves 217 cotton hand gloves 218 leather apron leather 219 safety boots for walders 220 gas welding goggles 221 ag 4 grinding wheels 222 students chairs with writing pads 223 lcd projector with screen. 224 welding process, inspection&codes dvd / cds. 225 lecture stand 226 pa system with wireless mic...

Department Of Supplies And Disposals - Haryana

23309911 tender for wire man, electrician and electronic machinery items for i.t.is of the state 1 wire man, electrician and electronic machinery items for i.t.is of the state 2 d.c. compound motor 3 h.p 250 v with 4 point starter and field regulator ( laboratory type ) 3 d.c. shunt motor 3 h.p 250 v with 3 point starter and speed regulator ( laboratory type 4 work bench , 2.5x1.20x0.75meters 5 electrical machine trainer – nsuitable for demonstrating the construction and functioning of different types of dc machines and ac machines ( single phase and three phase ) . should be fitted with friction brake arrangement, dynamo meter, instrument panel and power supply unit ( specifications attached ) n 6 motor generator ( dc to ac ) set consisting of shunt motor with starting compensator and switch directly coupled to ac generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. set complete with cast iron bed plate, fixing bolts, foundation bolts and flexible coupling. nshunt motor rating : 5 hp, 440v ac generator rating : 3 phase, 4 wire, 3.5 kva, 400 / 230 volts, 0.8 pf, 50cycles n 7 motor generator ( ac to dc ) consisting of : nsquirrel cage induction motor with star delta starter and directly coupled to dc shunt generator and switch board mounted with regulator, air breaker, ammeter, voltmeter, knife blade switches and fuses, set complete with case iron and plate, fixing bolts, foundation bolts and flexible coupling. ninduction motor rating: 7 hp, 400v, 50 cycles, 3 phase ndc shunt generator rating: 5 kw, 440v n...

Public Health Engineering Department - Haryana

21693629 tender for banawali shifting of rcc i / c from banawali minor to f / branch, special repair of w / w structures and cost.b / stn at banawali district fatehabad “painting and distempering of water works structures, supply of filter media ( for 3 no. filter bed of 27’ dia and 1 no. 16’x24’ ) and taking out filter media 2nd to bottom layer with the help of basket and stacking average depth about 10 and placing of filter media all layer after screened and washed and taking out and relaying of filter bed plates washing cross drains central drains with brush etc. complete in all respect. and all other works contingent thereto. at water works banawali...

Public Health Engineering Department - Haryana

20308980 tender for annual maintenances work for water supply 1 outsourcing of works/ job work for filter media washing etc. placing all layers of filter media after washing screening and cleaning / kherainti, outsourcing of works/ job work for filter media washing etc. taking out of all layer of filter beds of size and relaying in proper gradient after washing, screening and cleaning and taking out and relaying of filter bed plates washing cross etc. with mannual labour / kherainti,3 outsourcing of works/ job work for filter media washing etc. taking out rcc bed plate from filter bed and replacing of rcc bed plate after cleaning of drains / kherainti...

Industrial Training Institute - Haryana

19624450 supply of petty tools & equipment a. electric induction plate, b. electric kettle, c. electric iron, d. immersion heater, e. a.c. ceiling fan and ac table fan, f. geyser (storage type), g. mixture & grinder, h. washing machine semi automatic, i. motor pump set, oil testing kit, inverter with battery, voltage stabilizer, dc power supply, battery charger, current transformer, potential transformer, solar panel with battery, computer (i 3)or latest, ink jet/ laser printer, d.c. shunt generator with control panel, motor generator (ac to dc), d.c. compound generator with control panel including fitted rheostat, voltmeter, ammeter and breaker, dc series motor coupled with spring balance load, dc shunt motor, dc compound motor with starter, and switch, motor generator(dc to ac) set consisting of shunt motor with starting compensator and switch directly coupled to ac generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. set complete with cast iron bed plate,, fixing bolts, foundation bolts and flexible coupling., ac squirrel cage motor with star delta starter and triple pole iron clad switch fuse with mechanical load., ac phase wound slip ring motor with starter switch, universal motor with starter/switch, synchronous motor with accessories like starter, excitation arrangements., thyristor /igbt controlled d.c. motor drive with tacho generator feedback arrangement, thyristor/igbt controlled a.c. motor drive with, single phase transformer, core type, air cooled, three phase transformer, shell type oil cooled with delta/ star, electrical machine trainer –, diesel generator set with change over switch, over current breaker and water/ air cooled with armature, star delta connections ac 3 phase, used dc generators series, shunt and compound type for overhauling practice, pillar electric drill machine motorized, motorised bench grinder,...

Industrial Training Institute - Haryana

18814885 supply of petty tools & equipments for giti chhachhrauli : 513. motor generator ( dc to ac ) set consisting of shunt motor with starting compensator and switch directly coupled to ac generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. set complete with cast iron bed plate, fixing bolts, foundation bolts and flexible coupling. 514. ac squirrel cage motor with star delta starter and triple pole iron clad switch fuse with mechanical load. 515. ac phase wound slip ring motor with starter switch 516. universal motor with starter / switch 517. synchronous motor with accessories like starter, excitation arrangements. 518. thyristor / igbt controlled d.c. motor drive with tacho generator feedback arrangement 519. thyristor / igbt controlled a.c. motor drive with 520. single phase transformer, core type, air cooled 521. three phase transformer, shell type oil cooled with delta / star 522. electrical machine trainer –529. single phase capacitor motor with starter switch 530. manual motor coil winding machine 531. ceiling fan coil winding machine 532. primary current injection set 533. stepper motor with digital controller 534. shaded pole motor 535. working bench 536. wiring board 537. instructor’s table 538. instructor’s chair 539. metal rack 540. lockers with drawers 541. almirah 542. black board / white board 543. fire extinguisher co2 544. fire buckets 545. measuring tape 546. seam ripper 547. thimble 548. thread cutter 549. color plate 550. color brush 551. scale plastic 552. compass 553. hangers...

Industrial Training Institute - Haryana

18814873 supply of petty tools & equipments for giti chhachhrauli : 498. inverter with battery 499. voltage stabilizer 500. dc power supply 501. battery charger 502. current transformer 503. potential transformer 504. solar panel with battery 505. pentium iv computer or latest 506. ink jet / laser printer507. d.c. shunt generator with control panel 508. motor generator ( ac to dc ) 509. d.c. compound generator with control panel including fitted rheostat, voltmeter, ammeter and breaker 510. dc series motor coupled with spring balance load 511. dc shunt motor 512. dc compound motor with starter and switch513. motor generator ( dc to ac ) set consisting of shunt motor with starting compensator and switch directly coupled to ac generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. set complete with cast iron bed plate, fixing bolts, foundation bolts and flexible coupling. 514. ac squirrel cage motor with star delta starter and triple pole iron clad switch fuse with mechanical load. 515. ac phase wound slip ring motor with starter switch 516. universal motor with starter / switch 517. synchronous motor with accessories like starter, excitation arrangements. 518. thyristor / igbt controlled d.c. motor drive with tacho generator feedback arrangement 519. thyristor / igbt controlled a.c. motor drive with 520. single phase transformer, core type, air cooled 521. three phase transformer, shell type oil cooled with delta / star 522. electrical machine trainer –...

Public Health Engineering Department - Haryana

18762048 tender for estimate for providing and placing new filter media top layer and taking out top layer to bottom layer filter media from filter beds & replacing the same after washing, cleaning and screening & washing of rcc bed plate into filter bed at various rural w/s scheme, prov. & fixing of floating arms of sizes, 8x4mtr. long at existing in s/s tank at water works bajina and all other works contingent thereto....

Industrial Training Institute - Haryana

18759782 supply of machinery petty tools equipment and furniture 277 motor generator ( dc to ac ) set consisting of shunt motor with starting compensator and switch directly coupled to ac generator with exciter and switch board mounted with regulator, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. set complete with cast iron bed plate, fixing bolts, foundation bolts and flexible coupling. 278 synchronous motor with accessories like starter, excitation arrangements 279 thyristor / igbt controlled d.c moter drive with tacho generator feedback arrangement 280 single phase transformer, core type, air cooled 281 electrical machine trainer 282 diesel generator set with change over switch, over current breaker and water air cooled with armature, star delta connections ac 3 phase 283 pillar electric drill machine motorized 284 a.c series type motor 285 single phase capacitor motor with starter switch 286 manual motor coil winding machine 287 ceiling fan coil winding machine 288 primary current injection set 289 wiring board 290 fire extinguisher co2...

Industrial Training Institute - Haryana

18743268 supply of machinery, tool and equipment and furniture : 159 function generator 160 soldering iron 161 temperature controlled soldering iron 162 discrete component trainer 163 linear i.c. trainer 164 digital i.c. trainer 165 domestric appliances a. electric induction plate b. electric kettle c. electric iron d. immersion heater e. a.c celling fan and ac table f. geyser ( storage type ) g. mixture & grinder h. washing machine semi automatic i. motor pump set 166 oil testing kit 167 inverter with battery 168 voltage stabilizer 169 dc power supply 170 battery charger 171 current transformer 172 potential transformer 173 solar panel with battery 174 pentium iv computer or latest 175 ink jet / laser printer 176 d.c. shunt generator with control panel 177 motor generator ( ac to dc ) 178 dc compound generator with control panel including fitted rheostat, voltmeter , ammeter and breaker 179 dc series motor coupled with spring balance load 180 dc shunt motor 181 dc compound motor with starter and switch182 motor generator ( dc to ac ) set consisting of shunt motor with starting compensator and switch directly coupled to acgenerator with exciter and switch board and mounted with regulator, breaker ammeter voltmeter frequency meter , knife blade switch and fusese etc. set complete with cast iron bed plate, fixing bolts, foundation bolts and flexible coupling 183 ac squirrel cage motor with star delta starter and triple pole iron clad switch fuse with mechanical load...

Department Of Supplies And Disposals - Haryana

18247159 1. d.c. compound motor 3 h.p 250 v with 4 point starter and field regulator ( laboratory type ) estimated cost: 0.002. d.c. shunt motor 3 h.p 250 v with 3 point starter and speed regulator ( laboratory typeestimated cost: 0.003. m.g. set consisting of squirrel cage induction motor 5 h.p. 400 v cycle with directly coupled compound generator 3k.w. 250 v with built in panel board consisting of ( sr. no. 1 to 8 ) :estimated cost: 0.004. work bench , 2.5x1.20x0.75metersestimated cost: 0.005. electrical machine trainer – suitable for demonstrating the construction and functioning of different types of dc machines and ac machines ( single phase and three phase ) . should be fitted with friction brake arrangement, dynamo meter, instrument panel and power supply unit ( specifications attached ) estimated cost: 0.006. motor generator ( dc to ac ) set consisting of shunt motor with starting compensator and switch directly coupled to ac generator with exciter and switch board mounted with regulator, breaker, ammeter, voltmeter frequency meter, knife blade switch and fuses etc. set complete with cast iron bed plate, fixing bolts, foundation bolts and flexible coupling. shunt motor rating : 5 hp, 440v ac generator rating : 3 phase, 4 wire, 3.5 kva, 400 / 230 volts, 0.8 pf, 50cyclesestimated cost: 0.007. motor generator ( ac to dc ) consisting of : squirrel cage induction motor with star delta starter and directly coupled to dc shunt generator and switch board mounted with regulator, air breaker, ammeter, voltmeter, knife blade switches and fuses, set complete with case iron and plate, fixing bolts, foundation bolts and flexible coupling. induction motor rating: 7 hp, 400v, 50 cycles, 3 phase dc shunt generator rating: 5 kw, 440vestimated cost: 0.008. signal generator, 10 100 khz with digital display for frequency amplitude estimated cost: 0.009....

Public Health Engineering Department - Haryana

18140775 dnit for the work of repair and renovation of water supply scheme at village iqbalpur group of 5 no. villages, distt. gurugram “all layer taking out and replenishment of filter media from filter beds, drawing out rcc bed plates and all other works contingent thereto at village iqbalpur, distt. gurgram...

Public Health Engineering Department - Haryana

17900736 improvement of various rural water supply scheme recoupment top layer of filter media to a depth of 2 3 and taking out and washing of filter media of chocked filter beds in various rural water supply schemes under phe division hansi providing and placing top layer, taking out top, 2nd, 3rd, 4th layer and bed plates of filter media from filter beds and placing the same after washing, cleaning in filter beds, construction of filter media washing plate form and all other works contingent thereto...

Public Health Engineering Department - Haryana

17887830 replenishment of top layer and washing of filter media layers for smooth running of filter beds for rural water supply scheme under the jurisdictions of public health engineering division bahadurgarh. taking out all five layers of filter media and placing out, taking out rcc bed plate of size 16x16x2 from filter bed and replacing the same after washing and brushing, washing of cross drains and central drains with brush etc., providing and laying of top layer of filter media and all other works contingent thereto ( under public health engineering division bahadurgarh. ( water works dulhera, 4 nos. 29 i / d, water works kablana 4 nos. 24x23 ( only washing ) , water works chhudani 4 nos. 26x18 ( only washing ) , water works silothi 2 nos. of 32x20, water works mattan i.e. 4 nos. of 34x23, water works bhaproda i.e. 2 nos. of 34 i / d, 1 no. 25x37, water works rewari khera 1 no. 45x30, water works isher heri 4 no. 23 i / d, water works hassanpur parnala 4 no. 23x15 and old water works chhara i.e. 2 nos. 35 i / d, 1 no. 60x80, 2 nos. 32x50 and all other works contingent thereto...

Public Health Engineering Department - Haryana

17824702 tender for dnit for the work of repair and renovation of water supply scheme at village iqbalpur group of 5 no. villages, distt. gurugram “all layer taking out and replenishment of filter media from filter beds, drawing out rcc bed plates and all other works contingent thereto at village iqbalpur, distt. gurgram 1. workestimated cost: 565000.00...

Cooperative Sugar Mills Societies - Haryana

17543899 contract for dismantling, fabrication and erection work 76. dismantling, reparing and refitting of id fans of skoda boiler no. 1, 2, 3 and id fan of apcm. 77. repair of sugar grader no. 1 & 2 78. dismantling and errection of cooling coils of crystillizer. .83. repairing of internal structure of apcm wet scrubber. 84. dismantling , fabrication and errection of crystilizer driving drum 85. dismantling , fabrication and errection of vacuum filer mud shoot 700 mm x 3000 mm x 300 mm made of 8 mm m.s. plate. 86. dismantling, fabrication and errection of mud azitator of vacuum filture 87. dismantling, fabrication and errection of cane cutter foundation bed plate. 88. dismantling, fabrication and errection of 2 nos. under feed roller with grooving of 1 1 / 2 & 2 pitch 89. fabrication and errection of inter carrier structure ( 2 no. ) .90. dismantling, fabrication and errection of bagasse chute of bagasse elevator ( after mill no. 6 ) . 91. cleaning, digging and filling of sand, stone & bazri of 4 nos. apcm ash pit, size 12.5 mt x 13.5 mt x 1.3 m depth 92. dismantling, fabrication and erection of ms ducting per sqft. 93. dismantling of flanges 2dia to 6 dia and refitting after cleaning of the equipment ( without fabrication ) per inch dia. 94. dismantling of flanges 8dia to 40 dia and refitting after cleaning of the equipment ( without fabrication ) per inch dia. 95. dismantling of pipe lines 2 dia to 8 dia and refitting per inch dia per feetlength after cleaning the equipment ( without fabrication ) 96. dismantling and refitting of any reduction gear box. 97 dismantling of any reduction gear box and refitting of planetary reduction gear box with drive 98 opening of frp flanges and refitting after cleaning size 6 dia ( per pc ) 99 dismantling of frp pipe of size 6 dia and refitting after cleaning per length ( 64 to 104 length ) . 100 dismantling and refitting of frp cross of size 6 dia after cleaning ( per pc ) ....

Public Health Engineering Department - Haryana

17494899 tender for taking out all layer filter media from filter bed no.1 & 2 of size 20 dia and replacing after washing, screening, taking out bed plates & replacing after washing and rejointing of rcc pipe channel, repair of hodies, construction of sv hodi, open pucca inlet chhanel, v notch hodi cover, taking out filter media & replacing after washing, cleaning of water works shahpuria and all other works contingent thereto...

Public Health Engineering Department - Haryana

16187577 tender for taking out 2nd, 3rd, 4th, bottam layer including bed plates & replacing after washing, screening, cleaning and providing & placing top layer of filter media and all other works contingent thereto at water works rupana bishnoian (filter bed no.1 of size 20.00 dia)...

Public Health Engineering Department - Haryana

15885846 repair of various water works structures and taking out all layer filter media and filter bed no.1 of size 24.00x14.00 dia each and including bed plates and replacing the same after washing, screening and all other works contingent thereto at water works village mehna khera (ellenabad) (filter bed no.1 of size 24.00x14.00 each)”...

Public Health Engineering Department - Haryana

15884813 tender for repair of various water works structures and taking out all layer filter media and filter bed no.1 of sie 20.00 dia and including bed plates and replacing the same after washing, screening and all other works contingent thereto at water works village bacher (filter bed no.1 of size 20.00 dia)...

Public Health Engineering Department - Haryana

15434695 providing and laying of top layer of filter media, taking out all five layer of filter media and placing out, taking out rcc bed plates of size 16x16x2 from filter bed and replacing the same after washing and brushing, washing of cross drains and central drains with brush etc. and all other works contingent thereto”....

Public Works Department - Haryana

14897121 taking out all layer of filter media and rcc bed plate of size 16x16x2 from filter bed and placing of filter media all layer and bed plate after screening and washing and providing and placing top layer filter media and all other works contingent thereto at water works village kumharia ( filter bed no.1 of size 25.00 dia )...

Public Works Department - Haryana

14881514 annual maintenance water supply scheme danoda kalan takingout filter media of all layers with the help of basket ladder and stacking av depth 10 feet and placing of filter media of all layers after screening and washing complete in all respect takingout rcc bed plate of size 16x16x2 from filter bed and replacing the same after washing brushing washied of cross drains and central drain with brush etc and all other works contignent thereto...

Public Works Department - Haryana

14881494 annual maintenance water supply scheme danoda khurd takingout filter media of all layers with the help of basket ladder and stacking av depth 10 feet and placing of filter media of all layers after screening and washing complete in all respect takingout rcc bed plate of size 16x16x2 from filter bed and replacing the same after washiong brushing washied of cross drains and central drain with brush etc and all other works contignent thereto...

Public Works Department - Haryana

14103791 providing of filter media top layers taking out of all layers of filter media bed plates and placing the same after washing screening and cleaning at ww sanagtpura and all other works contingent thereto...

Public Works Department - Haryana

13842207 providing of filter media top layers, taking out of all layers of filter media bed plates and replacing the same after washing screening and cleaning and all other works contingent thereto....