Food Corporation Of India - Haryana

39807411 tender for annual repair and maintenance of and misc. repair works for the year 2023 24 at fsd karnal; 1 dismantling barbed wire or flexible wire rope in fencing including making rolls and stacking within 50 metres lead. 2 dismantling steel work in single sections including dismembering and stacking within 50 metres lead in:channels, angles, tees and flats 3 demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge.in cement mortar 4 dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead 5 demolishing r.c.c. work manually / by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge 6 dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: asbestos cement sheet 7 earth work in excavation by mechanical means ( hydraulicexcavator ) / manual means over areas ( exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan ) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by engineer in charge.all kinds of soil 8 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level :1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) 9 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.cold twisted bars 10 centering and shuttering including strutting, propping etc. and removal of form for :foundations, footings, bases of columns, etc. for mass concrete 11 centering and shuttering including strutting, propping etc. and removal of form for :lintels, beams, plinth beams, girders, bressumers and cantilevers 12 structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 13 providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all work up to plinth level : 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources ) 14 centering and shuttering including strutting, propping etc. and removal of form for : columns, pillars, piers, abutments, posts and struts 15 reinforced cement concrete work in walls ( any thickness ) , including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing andreinforcement :1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources ) 16 centering and shuttering including strutting, propping etc. and removal of form for suspended floors, roofs, landings, balconies and access platform 17 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources ) . 18 removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m ( stacks of cleaned bricks shall be measured ) :from brick work in cement mortar 19 brick work with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in foundation and plinth in: cement mortar 1:6 ( 1 cement : 6 coarse sand ) with available bricks ( with available bricks ) 20 brick work with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in : cement mortar 1:6 ( 1 cement : 6 coarse sand ) with available bricks ( with available bricks ) 21 brick work with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in : cement mortar 1:6 ( 1 cement : 6 coarse sand ) 22 centering and shuttering including strutting, propping etc. and removal of form for small lintels not exceeding 1.5 m clear span, moulding as in cornices, window sills, string courses, bands, copings, bed plates, anchor blocks and the like 23 supplying at site angle iron post & strut of required size including bottom to be split and bent at right angle in opposite direction for 10 cm length and drilling holes upto 10 mm dia. etc. complete. 24 providing and laying cement concrete in retaining walls, return walls, walls ( any thickness ) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing: 1:2:4 ( 1 cement : 2 coarse sand ( zone iii ) : 4 graded stone aggregate 20 mm nominal size 25 15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 ( 1 cement: 6 fine sand ) 26 12 mm cement plaster of mix :1:6 ( 1 cement: 6 fine sand ) 27 6 mm cement plaster of mix : 1:3 ( 1 cement : 3 fine sand ) 28 fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m ( minimum ) , between the two posts fitted and fixed with g.i. staples, turn buckles etc. complete. ( cost of posts, struts, earth work and concrete work to be paid for separately ) . payment to be made per metre cost of total length of barbed wire used. with g.i. barbed wire 29 distempering with 1st quality acrylic distemper, having voc ( volatile organic compound ) content less than 50 grams / litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.two coats 30 painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : one or more coats on old work 31 regrading terracing of mud phaska covered with tiles or brick, in cement mortar by dismantling tiles or bricks, removing mud plaster, preparing the surface of mud phaska to proper slope, relaying mud plaster gobri leaping and tiles or bricks, grouted in cement mortar 1:3 ( 1 cement : 3 fine sand ) , including replacing unserviceable tiles or bricks with new ones and disposal of unserviceable material to the dumping ground ( the cost of the new tiles or brick excluded ) , all complete as per direction of engineer in charge. 32 structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 33 credit of old iron scrap including loading / unloading / disposal etc as per direction of engineer in charge 34 credit for old unserviceable ac sheets 35 disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by engineer in charge, beyond 50 m initial lead, for all leads including all lifts involved....

Haryana Board Corporation - Haryana

39704188 supply of furniture items to the fatehabad central cooperaive bank ltd supply installation of officer chair almirah metal rack three seater chair in head office of the fatehabad central co operative bank ltd , details , fixed chair : fixed visitor chair, overall dimension: 530w ±10 x 580d ±10 x 840h ±10 mm, seat & back of chair is made 12mm thick hot pressed plywood cushioned with pu moulded foam fabric upholstery, pvc beading used in seat & back, seat & back fixed with ms powder coated plate, used pu foam on seat of d 45 kg / m3, used foam on back of d 45 kg / m3, seat size: 460w ±10x 405d ±10 x 60thick. ±5 mm, back size: 460w ±10 x 415h ±10 x 60thick. ±5mm, armrest: armrest made of good quality injection moulded ppcp cover fixed with 16gauge powder coated round pipe of 25.4mm, armrest fixed with seat & back, under structure: cantilever frame made of 25.4mm round pipe with 14 gauge thickness duly powder coated with plastic bushes . , revolving chair:: medium back revolving chair, overalldimension: 715w:1:10 x 715d :1:10 x 1020h :1:10 mm . seat of medium back chair is made of 12mm thick hot pressed plywood pasted with pu moulded foam with fabric upholstery on seat , used pu moulded foam on seat of d 45 kg / m3 , back of medium back chair is made of injection moulded pp material structure in black colour upholstered with mesh fabric , seat size: 510w :1:10 x 510d :1:10 x 60thick. :1:5 mm , back size: 460w :1:10 x 490h :1:10 mechanism: centre tilt mechanism single point control, pmvides maximum adjustability and scope for comfort , seat & back are fixed together with arms & whole structure moves together in one direction , single / upright position locking , tilt tension knob to loosen or tighten the tension according to users body weight . gaslift: lift used gaslift of 85 mm size of class iv grade , pllastic gas lift cover . armrest: fixed pp armrest in black colour, seat & back connected with arms . chair base & wheels: revolving pedestal metalinserted ppcp base consists of 5 prongs with 660:1:5 mm pitch circle diameter, 50mm dia. black nylon twin wheel pin castor , almirah:: overall size 915w x 485d x 1980h , top , bottom , side panel & shelve made up of 0.8mm thick crca sheet powder coated , legs made up of 0.8mm thick crca sheet powder coated , shutter made up of 1mm thick crca sheet powder coated , no sharp edges of almirahends , all shelve rack divided into equal parts , door die cast chrome plated handles fitted with washer & double nut , handles ring made ofpvc cap , almirah all metallic panelsscrew with nut & bolt , all metal pieces shall be welded properly strongly and conformity with regulations with co2 welding shall be used , crca metal shall be coated after being treated with at least three stages and cleaned from oil , grease dust and other dirt using special thermal control coating for metal furniture to form a layer of base coating of ( iron phosphating ) ( 0.4 – 0.8 ) gm / m² automatic spray coating shall be applied to be followed by a drying process in a thermal furnace with suitable temperature and time for the process , metal pipe & 7 tank treatment with minimum 45 50 micron powder coating . , slotted angle rack :: slotted angle rack overall size : 900wx450dx1800h mm, angle made up of crca 40x40x2mm thick duly powder coated, shelve made up of crca 0.8 mm thick duly powder coated, corner plate made up of crca 1 mm thick duly powder coated, slotted angle rack should be supplied in knock down condition , high quality ppcp shoes should be used on bottom to avoiding scratches on the floor , all metal components should be pre treated with zinc phosphating in minimum 7 tank process and the powder coated with epoxy polyester with approved shade , thickness of coating should be minimum 50 microns . , three seater waiting chair ::dimensions : 200x60x30 cm, chrome plated, no. of seats 3, heavy duty steel frame that is strong and stable. the frame is powder coated for added strength and durability and features adjustable legs for a perfect fit. the chair also features a breathable mesh backrest and upholstered armrests for extra support and comfort....

Urban Local Bodies - Haryana

39572825 tender for for construction at dhanak sabha fatehabad 1 [10.100.2]cement concrete 1:8:16 flooring 2. cement concrete 1:8:16 with stone aggregate 40 mm size in foundation and plinth. 2 [10.51]providing and fixing granite stone in all shades 15mm to 18 mm thickin skirting /dado, risers of steps, pillars and wall facing, laid in any pattern as specified over base of 12mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade ofgranite including labour for fixing cramps pins and dowels etc. 3 [10.58]providing and fixing 1st quality ceramic glazed wall tiles conforming to is : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by engineer in charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. 4 [10.77]providing and laying 80mm thick factory made cement concrete interlocking paver block of m 35 grade made by block making machine with strong vibratory compaction, of approved size, design and shape, laid in required colour and pattern over (bis 15658:2006) and including 60mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of engineer in charge. 5 [11.5.3]12 mm cement plaster of mix : 3. 1:4 (1 cement: 4 fine sand) 6 [11.57]providing and laying average 6mm thick pop coatingon walls, ceiling, beams and lintels etc. complete in all respects as approved by the engineer in charge. 7 [11.6.1]15 mm cement plaster on the rough side of single or half brick wall of mix : 1. 1:4 (1 cement: 4 fine sand) 8 [11.67.1]applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : 1. water thinnable cement primer 9 [11.68.2]applying priming coat: 2. with ready mixed aluminium primer of approved brand and manufacture on resinous wood and plywood 10 [11.71.1]wall painting on a cement plaster surface with acrylic emulsion paint of approved brand and manufacture to give an even shade : 1. two or more coats on new work 11 [11.78]painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. 12 [13.35]providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of t iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer. 13 [13.41]providing and fixing stainless steel ( grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories and stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of engineer in charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). 14 [4.14.1]earth work in excavation by mechanical means (hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 1. all kinds of soil. 15 [5.7.4]demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge. 4. in cement mortar 16 [6.16]reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone iii): 3 graded stone aggregate 20 mm nominal size). 17 [6.30.3]centering and shuttering including strutting, propping etc. and removal of form for 3. suspended floors, roofs, landings, balconies and access platform 18 [6.30.5]centering and shuttering including strutting, propping etc. and removal of form for 5. lintels, beams, plinth beams, girders, bressumers and cantilevers 19 [6.34.6]steel reinforcement for r.c.c. work, where not included in the complete rate of rcc, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect above plinth level. 6. thermo mechanically treated bars of grade fe 500d or more. 20 [7.21.1]brick work with common burnt clay non modular bricks of class designation 10.5 in foundation and plinth in: 1. cement mortar 1:4 (1 cement : 4 coarse sand) 21 [7.22.1]brick work with common burnt clay non modular bricks of class designation 10.5 in superstructure above plinth level up to floor iv level in all shapes and sizes in : 1. cement mortar 1:4 (1 cement : 4 coarse sand) 22 [9.10.1]painting top of roofs with bitumen of approved quality @ 17kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm, including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil complete : 1. with residual type petroleum bitumen of grade vg 10 23 [9.14.1]providing and laying brick tiles over mumty roofs, grouted with cement mortar 1:3 (1 cement : 3 fine sand) mixed with 2% of integral water proofing compound by weight of cement, over 12 mm layer of cement mortar 1:3 (1 cement : 3 fine sand) and finished neat: 1. with common burnt clay non modular brick tiles of class designation 10 24 [9.57.1]providing and fixing on wall face unplasticised rigid pvc rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, leaving 10 mm gap for thermal expansion, (i) single socketed pipes. 1. 75 mm diameter ...

Northern Railway - Haryana

39340569 auction sale of scrap re & signaling material consisting of pillers, post, pipes, rounds, g. i.& m.s pipes,junction box with or w/o electrical fitting if any, s & t boxes,tia bar, rods,signaling light fitting, fire extinguisher, and other fs/ nfs attachments if any, angles,trd items,signal pipes & electric poles, poles,signal post,galv. wire, mast (trd),cantilever,signal post, ladder, wire ropes, lever,mast, girder,other structure, mixed with other m.s. & c.i. scrap including nut bolts etc of sorts & sizes with or w/o nfs attachment if any, us & ur,as it is. (qty are in approx.basis) remarks: [1] loading by purchaser[2].cutting allowed for loading purpose only.[3].cutting will be allowed after following all the fire prevention related instruction of judw depot[4].private road crane allowed for loading purpose....

J.C. BOSE University of Science and Technology - Haryana

39292637 tender for office furniture for r&d cell 01 executive table specification : providing and placing in position table. overall size of table shall be 1650 width x 700 depth x 743 height (main desk) 1000 width x 450depth x 743 height (eru).top shall be of 18 mm thickness made of plt board with 2 mm edge banding. wenge and savannah maple plt board shall be used. the understructure shall be in pre laminated panels made with plt boards. 2 drawer and 3 drawer storage units with different combinations to support tops made with 18 mm plt boards of different colours. modesty and back panels made with 18 mm plt boards. the pedestals / storages shall be fitted with necessary locks. 01 02 work table specification : providing and placing in position table. over all size of table shall be 1200 width x 600 depth x 750 height mm. the table panels shall be made from 18 ±0.5mm thk pre laminated exterior grade plt ( grade i, type ii )(is 12823) with pvc edge banding on all sides. drawer bottom panels shall be made up of 9mm thick (±1mm)prelaminated particle board. locking shall have been provided on top drawer only. table shall have provision of cpu monitor, drawer and sliding kbpt. the table shall have a knock down construction 04 03 storage unit low height specification : providing and placing in position storage unit . construction shall be a knockdown construction of 25mm thk and 18mm thk pre laminated boards with metal cladding of 0.8mm thk c.r.c.a (as per is:513) from outside. side metal cladding shall be coated with epoxy polyester powder of 50±10 microns thickness. wooden top shall be made of 25mm thick pre laminated board. the doors shall be made of 18mm thk pre laminated boards with decorative laminate on one side and backing laminate on the other side. height wise adjustable shelf mounting holes provided on side panels for easy interchange of shelf height as required. uniformly distributed load capacity for each shelf shall be be 40kg maximum. the skirting units shall be provided with 150mm high skirting made of 0.8mm thick c.r.c.a (as per is: 513) which shall be coated with epoxy polyester powder of 50±10 microns thickness. screw type adjustable leveler with plastic base shall be provided for vertical adjustment for floor unevenness and leveling of units. back panels shall be made of 18mm thick pre laminated boards with options of decorative laminate as well as fabric finishes. it shall consist of single back panel.3 way nickel plated wooden furniture lock to be provided for effective and positive locking of doors. aesthetically appealing recessed handles of aluminium extrusion shall be provided for easy opening and closing. 02 04 storage unit full height specification 03 : providing and placing in position almirah. almirah with 4 shelves shall have an overall size of 900mm(w)x450mm(d)x1830mm(h). the construction shall be rigid knock down construction and material used shall be prime quality crca steel panels from 0.6 mm thick & front frame. shelf shall be 0.8 mm thick. configuration (door) shall be full height steel hinged door . locking shall be plastic recessed handle cum cam lock with 3 way locking mechanism with shooting bolt arrangement. height wise adjustable shelf mounting, uniformly distributed load capacity per each full shelf shall be 80 kg maximum. the top shall be metal and epoxy powder coated finish to the thickness of 50 microns. product shall be green guard (ul) certified. 05 director’s chair specification : providing and placing in position high back chair for ms cabin. overall size of 76.1 cm w x 76.1 cm d x 112.7 – 130.2 cm h x 43.1 – 53.1 cm seat height. the seat is cushioned seat made of injection molded plastic outer & inner. plastic inner is upholstered with leatherette and molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per is:7888 for 25% compression. seat size is 47.0 w cm x 48.0 d cm. the back is cushioned made of pu foam with insitu molded m.s. erw round tube of size 1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. the back size is 47.7 w cm x 76.4 d cm. the armrest top is molded from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of ø3.81±0.03cm x 0.2±0.01cm thick m.s. erw tube having chrome plated finish. the armrest is height adjustable up to 6.5±0.5 cm in 5 steps. the adjustable tilting mechanism is designed with following features : 360° revolving type, front pivot for tilt with feet resting on ground and continuous lumbar support ensuring more comfort, tilt tension adjustment can be operated in seating position, 5 position tilt limiter giving option of variable tilt angle to the chair, seat/back tilt ratio 1:2, the mechanism housing is made up of hpdc aluminium black powder coated. seat depth adjustment is integrated in the seat through a sliding mechanism. seat depth adjustment range is of 6.0±0.5cm. back frame is connected to the up/down mechanism in plastic t spine. it can be adjusted in the range of 7.42±0.5 comfort the comfortable back support to suit individual need. the pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm. the pedestal is high pressure die cast polished aluminium & fitted with 5 nos. of twin wheel castors. the pedestal is 65.0±0.5cm pitch centre dia. (75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection molded in plastic having 6.0±0.1cm wheel diameter and assembled to pedestal. product shall be green guard (ul) and bifma level 2 certified 01 06 executive chair specification : providing and placing in position high back chair the cushioned seats shall be made of injection moulded plastic outer and inner. plastic inner shall be upholstered with pure leather and moulded high resiliance polyurethane foam of density = 45±2 kg/m³, and hardness load 16±2 kgf as per is:7888 for 25% of compression. seat size shall be 47.6 cm w x 49.2 cm d. the back shall be cushioned and shall be made up of pu foam with insitu moulded ms erw round tube of size 1.9±0.03 cm x 0.16±0.0128 cm, upholstered with pure leather. back size shall be 47.5 cm w x 77 cm d. the armrest top shall be moulded from polurethane, and shall be upholstered with pure leather and mounted on ot a drop lift adjustable type tubular armrest support made up of ø3.81±0.03 cm x 0.2±0.01 cm thick ms erw tube having chrome plated finish. the armrest hieght shall be adjustable upto 6.5±0.5 cm in 5 steps. the adjustable tilting mechanism shall be designed with the following features : 360° revolving type, front pivot for tilt with feet resting on ground and contionuous lumbar support ensuring more comfort, tilt tension adjustment can be operated in seating position, 5 position tilt limiter giving options of variable tilt angle to the chair, seat/backtilting ratio 1:2, the mechanism housing is made up of hpdc aluminium black powder coated. seat depth adjustment shall be integrated in the seat through a sliding mechanism. seat depth adjustment range shall be 6.0±0.5 cm. back frame shall be connected to the up/down mechanism housed in plastic t spine. it can be adjusted in the range of 7.42±0.5 cm for the comfortable back support to suit individual need. the pneumatic height adjustment shall have an adjustment stroke of 10±0.3 cm. the pedestal shall be high pressure die cast polished aluminium and fitted with 5 nos. of twin wheel castors. the pedestal shall be 65.0±0.5 cm pitch centre dia. 5 nos. of twin wheel castors shall be injection moulded in plastic having 6.0±0.1 cm wheel diameter and assembled to pedestal. product shall be green guard (ul) and bifma level 2 certified 07 visitor chair specification: providing and placing in position visitor back chair.seat/back assembly: the cushioned seat shall be made of injection molded plastic outer & inner. plastic inner shall be upholstered with stitched cover and moulded high resilience polyurethane foam of density 45±2 kg/m3,and hardness load 16 ± 2 kgf for 25% compression.the stitched cover shall be made from spacer fabric and leatherette. cushioned back shall be made of pu foam with insitu molded ms e.r.w round tube of size 1.9±0.03cm x 0.16 ±0.0128cm. it upholstered with spacer fabric and leatherette. seat size : 47.0 cm. (w) x 48.0 cm. (d) back size : 45 cm. (w) x 60.5 cm. (d) visitor tubular frame: the powder coated (dft 40 60 micron) tubular frame shall be cantilever type & made of 02.54±0.03 cm x 0.2±0.016 cm thk ms erw tube.the back connected to frame through powder coated (dft 40 60 micron) high pressure die cast connector piece. overall dimensions of chair shall be seat height 44.8cm. height 99.5cm. width 60.9 cm and depth 64.3 cm product shall be green guard (ul) and bifma level 2 certified 08 08 centre table specificatoin: providing and placing in position centre table. overall size of the table shall be width : 100cm x depth : 65cm x height : 45cm. table top material shall be 10 mm thk tempered glass. table top material shall be 6 mm thk tempered glass. table legs material & size : l x w x t 70 x 70 mm with pu coating 01 09 3 seater sofa specification : providing and placing in position 3 seater sofa . overall size of sofa shall be w 1750 x d 800 x h 835 mm material of sofa upholstery shall be syn leather of 1 mm thickness. frame material shall be pine wood. moisture content : 10 12 %. thickness of plywood used shall be: 12 mm & 18 mm seat foam :material : slab stock density : 32 kg/m3 at seat back foam :material : slab stock density : 28 kg/m3 at seat webbing material : nylon legs : material : pvc ...

National Highways Authority Of India - Haryana

38761323 tender for hiring of agency for providing & fixing of cantilever sign board (6100x3050mm) and advance direction sign board (2440x2440mm) single sided as per irc 67 2012 (including all subsequent revisions thereof) with retro reflective high intensity micro prismatic grade reflective sheeting type xi as per astm d4956 09 for indication of direction of narnaul ambala section through nh 152d...

Northern Railway - Haryana

38463999 auction sale of scrap re & signaling material consisting of pillers, post, pipes, rounds, wire ropes, pullies of c.i / cast aluminium pullies, junction box with or w / o electrical fitting if any, s & t boxestia bar, rods, signaling light fitting, fire extinguisher, and other fs / nfs attachments if any, angles, trd items, signal pipes & electric poles, poles, signal post with or w / o nfs attachment, galv. wire, mast ( trd ) , cantilever, , ladder, wire ropes, lever, mast, girder, other structure, mixed with other m.s. & c.i. scrap etc of sorts & sizes with or w / o nfs attachment if any, us & ur, as it is. ( qty are in approx.basis ) loc: lying at two places: 1. lying at bin no. b 13 and 2. lying at open ground umb end in scrap yard judw remarks: [ 1 ] loading by purchaser [ 2 ] .cutting allowed for loading purpose only. [ 3 ] .cutting will be allowed after following all the fire prevention related instruction of judw depot [ 4 ] delivery will be given first from bin no.b 13 and after that from open ground umb end. [ 5 ] . private road crane allowed for loading purpose....

Northern Railway - Haryana

38184505 auction sale of scrap re & signaling material consisting of pillers, post, pipes, rounds, g.i. pipes, junction box with or w / o electrical fitting if any, s & t boxestia bar, rods, signaling light fitting, fire extinguisher, and other fs / nfs attachments if any, angles, trd items, signal pipes & electric poles, poles, signal post, galv. wire, mast ( trd ) , cantilever, signal post, ladder, wire ropes, lever, mast, girder, other structure, mixed with other m.s. & c.i. scrap etc of sorts & sizes with or w / o nfs attachment if any, us & ur, as it is. ( qty are in approx.basis ) loc: lying at near gate no.02 in scrap yard judw. remarks: [ 1 ] loading by purchaser [ 2 ] .cutting allowed for loading purpose only. [ 3 ] .cutting will be allowed after following all the fire prevention related instruction of judw depot [ 4 ] . private road crane allowed for loading purpose....

Board Of School Education - Haryana

38137147 tender for purchase of student desks and chairs 2 student chairspecification: chair with ergonomic design for user comfort. the seat and back shall be made of moulded polypropylene shell supported on powder coated metal frame. the frame structure shall be supplied with cantilever type made of ms crca powder coated 40 60 ( dft ) thick tubular pipe of size 38mm x 19mm with 1.6mm with 1.6 mm thick. one nos. footstep shall be welded between both legs for structural support. grooves handle shall be made the back of the chair for easily keeping and moving of the chair. there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 400±10mm ( d ) x 375±10 mm ( w ) and back size shall be 425+10 mm ( w ) x 350±10 mm ( h ) from seat. overall height shall be =710±10mm, overall depth=510±10mm &overall width=440mm±10mm 3 student desk specification: single seater student table. the top shall be made of 18mm thick pre laminated particle board of grade ii of is 12823 with approved laminate. the profile of the table shall be in rectangle shape with round corner and the edges shall be sealed with 2 mm thick thin strip of impermeable pvc that is cut to fit the size of board panel with the assistance of edge banding machine at 200 degree celsius. the top shall be supported on crca powder coated tubular pipe having size 38mm x 19mm with 1.6mm thick. the table shall be supplied with shelf made of powder coated round wires of dia. 5mm and 8 mm. the shelf shall be supported with tubular pipe having cross section area 38mm x 19mm which is placed between both legs and welded together. the table understructure shall be supplied on cantilever support type frame made of crca powder coated pipe having size 38mm x 19mm. one nos. footstep shall be provided between both sides of the leg and welded together. there shall be hooks provided at both side of the table for carrying the bag or bottle. ppcp shoe shall be provided at the base to avoid scratches on the floor as well as uneven flooring. the overall size of the table shall be 600mm ( w ) x 400mm ( d ) x 760mm ( h ) ...

Panchayat Raj Department - Haryana

38132368 tender for supply of furniture for 11 no. vkc building in distt. kaithal 1 supply of furniture for 11 no. vkc building in distt. kaithal 2 sarpanch table providing and placing of table with dimensions 2100 width x 900 depth x 740 height . the top shall be made from 25 mm thick pre laminated board . all the edges are sealed with 2 mm thick pvc edge band all around . side panels shall be made from 25 mm thick pre laminated paticle board . all the edges are sealed with 2 mm thick pvc edge band on the user side and 0.8 mm on the top and bottom side .the side panels have 2 glide screws each for levelling of the desk.modesty panel shall be made from 18 mm thick pre laminated particle board . all the edges are sealed with 0.8 mm thick pvc edge band all around. freestanding pedestal shall be made from 18 mm pre laminated particle board with a combination of 2 mm and 0.8 mm pvc edge band on all the exposed surfaces as per requirement .the drawers are provided with suitable slides for smooth operation . all the pedestal drawers are centrally locked with a single key . the oem should be havig valid iso 9001:2015, iso 14001:2015 , iso 50001:2018 , iso45001:2018 certificates as per nabcb guidelines. the certifying agencies should be accredited by nabcb. 3 sarpanch revolving chair high back : providing and placing of valid iaq gold certified high back chair. the seat and back should be made up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should be designed with contoured lumbar support for extra comfort. the seat has extra thickfoam on front edge to give comfort to popliteal area. back size should be 47.5 cm. ( w ) x 69.5 cm ( h ) and seat size should be 47.0 cm. ( w ) x 48.0 cm. ( d ) the hr polyurethane foam should be moulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgf for 25% compression. the one piece armrests should be injection moulded from black co polymer polypropylene. the mechanism should be central tilt synchro designed with the following features: • 360° revolving type. • upright position locking • tilt tension adjustment• seat / back tilting ratio of 1:3. the pneumatic height adjustment has an adjustment stroke of 12.0 ±0.3cm.the bellow should be 3 piece telescopic type and injection moulded in black polypropylene. the pedestal should be injection moulded in black 33% glass filled nylon 66 and fitted with 5 nos. twin wheel castors. the pedestal should be 66.3±0.5cm. pitch center dia. ( 76.3 ±1.0cm with castors ) . .the twin wheel castors should be injection moulded in black nylon. overall dimensions of chair seat height min 42.5 to max 54.5cm. height min97.0 to max 109.0cm. width & depth of chair as measured from pedestal width 76.3 cm and depth 76.3 cm. the oem should be havig valid iso 9001:2015, iso 14001:2015 , iso 50001:2018 , iso45001:2018 certificates as per nabcb guidelines. the certifying agencies should be accredited by nabcb. the product certifications likegreen guard, iaq gold, green pro, bifma from valid certification bodies to be uploaded with the bid and quoted model name to be present on thecertification website. 4 sarpanch visitor chair : providing and placing of valid iaq gold certified visitor chair . the seat and back should be made up of 1.2 ±0.1cm. thick hot pressed plywood and upholstered with .fabric upholstery covers and moulded polyurethane foam. the back foam should be designed with contoured lumbar support for extra comfort. the seat has extra thick foam on front edge to give comfort to popliteal should be area back size 47.5 cm. ( w ) x58.0 cm ( h ) seat size 47.0 cm. ( w ) x 48.0 cm. ( d ) the hr polyurethane foam should be moulded with density = 45±2 kg / m3 and hardness load 16 ± 2 kgf for 25% compression. the one piece armrests should be injection moulded from black co polymer polypropylene. the powder coated ( dft 40 60 microns ) tubular frame should be cantilever type & made of 0 2.54 ±0.03cm. x 0.2±0.016cm.thk. m.s. er.w. tube.overall dimensions of chair seat height 46.5cm. height 89.5cm. width & depth of chair as measured from pedestal width 61.4 cm and depth 64.5 cm. the oem should be havig valid iso 9001:2015, iso 14001:2015 , iso 50001:2018, iso 45001:2018 certificates as per nabcb guidelines. the certifying agencies should be accredited by nabcb. the product certifications like green guard, iaq gold, green pro, bifma from valid certification bodies to be uploaded with the bid and quoted model name to bepresent on the certification website. 5 table for meeting room : providing and placing in place of iaq certified conference table. the overall dimensions of the table shall be 4200 x 1200 x 750mm. these terminating leg structure shall be in m.s. crca sheet / tubes / rods as per is. 513 / 7138 / 432 finished with epoxy power coating of the approved colour as per the project designer.worktop shall be made of 25mm thickpre laminated board conforming to is: 12823. all the edges of work surface shall be provided with machine pressed 2 mm thick pvc lipping glued with hot melt eva glue. cross members in the upbeat system are made from 50 mm x 25 mm x1.2 mm thick. cross members are assembled by friction fit pdc joinery and grub screws. all cross members are mounted at a distance of 165 mm from worktop sides. wire management: wire tray with integrated power box made with a combination of 0.6 mm thick crca outer body and 0.8 mm thick crca switch plate ( 8+3 anchor roma ) module cut out as standard. they are mounted on worktop. the oem should be havig valid iso 9001:2015, iso 14001:2015 , iso 50001:2018 , iso 45001:2018 certificates as per nabcb guidelines. the certifying agencies should be accredited by nabcb. the product certifications like green guard, iaq gold, green pro, bifma from valid certification bodies to be uploaded with the bid and quoted model name to be present on the certification website. 6 chairs for meeting room : providing and placing of valid iaq gold certified visitor chair . the seat and back should be made uo injection moulded high impact strenght polypropylene polymer compound with indoor graade uv resistance.the tubular weled frame is made from dia2.22 + / 0.03cmx 0.12+ / 0.0128 cm and 3.5+ / 0.03 cm x 0.12+ / 0.0128 am stainless steel 202 grade tube.the tube are buff polished to give shiny finish. cm. the shoes are made of high impact strenght polypropylene polymer compond with indoor grad uv resistance and pressed fitted with tubularfram. size : ( w ) 52.5cm* ( d ) 55.8cm* ( h ) 84.5cm* ( seat h ) 45.0 cm. seat size 52.5cm ( w ) *53.2 cm ( d ) back size51.6 cm ( w ) *40.5 cm ( h ) . the oem should be havig valid iso 9001:2015, iso 14001:2015 , iso 50001:2018 , iso 45001:2018 certificates as per nabcb guidelines. the certifying agencies should be accredited by nabcb. the product certifications like green guard, iaq gold, green pro, bifma from valid certification bodies to be uploaded with the bid and quoted modelname to be present on the certification website. 7 staff chair : providing and placing of valid iaq gold certified chair wherein the chair should have one common frame of seat and back. the cushioned seat assembly consists of seat base moulded inglass filled poly amide, moulded polyurethane foam & upholstered with high stretch knitted polyester fabric. the cushioned back assembly consists of back inner moulded in polypropylene in situ moulded with polyurethane foam & upholstered with high stretch knitted polyester fabric. full back size : 45.5 cm. ( w ) x 53.0 cm. ( h ) *seat size :48.5 cm. ( w ) x 49.0 cm. ( d ) the hr polyurethane foam used in seat and back cushion is moulded in density 45±2 kg / m3, and hardness load 16 ± 2 kgf as per 15:7888 for 25%compression. the seat and back are firmly connected to the base frame and are cantilevered in such a way that it gives a multi dimensional movement possibility just with a simple lean on the sides or back, without need for complex manual adjustments. the cantilevered seat offers impact cushioning while sitting and synchronises with the back movement during posture changes. the 5 shaped spines moulded in high strength glass filled poly amide and the spine connector moulded in glass filled poly am ) de form theback spine structure involved inmulti dimensional recline motion. the variable tilt angle recline motion can be adjusted with 3 position tilt limit feature which is inbuilt in seat base and the tension ( return force ) is user weight dependent. the assembly consists of armrest housing sliding over the armrest structure, both moulded in glass filled poly amide. the height adjustment feature is button operated having adjustment of 6.6±0.5cm. the armrest top is made up of integral skin pu moulded over plastic inner moulded in glass filled poly amide.the seating height can be adjusted with a pneumatic gas lift having an adjustment stroke of 9.2 ± 0.3 cm the pedestal is injection moulded in glass filled poly amide and fitted with 5 nos. in wheel castors. the pedestal is 66.0±0.5 cm. pitch centre diameter and 76.0±1.0 cm. with castors. twin wheel castors are injection moulded inpoly amide having 5.0±0.1cm heel diameter and assembled to the pedestal. the powder coated ( dft 40 60 micron ) tubular frame is cantilever type & lade of 02.54±0.03 cm x 0.3±0.016 cm thk ms erw tube. shoes are made of glass filled poly amide and fixed the tubular frame.dimensions measured out to out extreme point ) on components in knockdown condition, variations within ±1.0 cm. ( w ) 76 ( d ) 76* ( h ) 99.5 108.8cm seat ( h ) 44.5 53.8cm. the oem should be havig valid iso 9001:2015, iso 14001:2015 , iso 50001:2018 , iso 45001:2018 certificates as per nabcb guidelines. the certifying agencies should be accredited by nabcb. the product certifications like green guard, iaq gold, green pro, bifma from valid certification bodies to be uploaded with the bid and quoted model name to be present on the certification website...

Northern Railway - Haryana

37898859 auction sale of scrap re & signaling material consisting of pillers, post, pipes, rounds, wire ropes, pullies of c.i/ cast aluminium pullies,aluminium sign plate,junction box with or w/o electrical fitting if any, s & t boxestia bar, rods,signaling light fitting, fire extinguisher, and other fs/ nfs attachments if any, angles,trd items,signal pipes & electric poles, poles,signal post,galv. wire, mast (trd),cantilever,signal post, ladder, wire ropes, lever,mast, girder,other structure, mixed with other m.s. & c.i. scrap etc of sorts & sizes with or w/o nfs attachment if any, us & ur,as it is. (qty are in approx.basis)loc: lying at two places: 1. lying at bin no. c 96 and 2. lying at bin no. a 37 in scrap yard judw remarks: [1] loading by purchaser[2].cutting allowed for loading purpose only.[3].cutting will be allowed after following all the fire prevention related instruction of judw depot[4] delivery will be given first from bin no.c 96 and after that from bin no. a 37. [5]. private road crane allowed for loading purpose....

Northern Railway - Haryana

37770558 auction sale of scrap re & signaling material consisting of pillers, post, pipes, rounds, wire ropes, pullies of c.i/ cast aluminium pullies,junction box with or w/o electrical fitting if any, s & t boxestia bar, rods,signaling light fitting, fire extinguisher, angles,trd and s & t items , token box machine, parts of point machine,signal pipes & electric poles, poles,signal post,galv. wire, mast (trd),cantilever,signal post, ladder, wire ropes, lever,mast, girder,other structure, mixed with other m.s. & c.i. scrap etc of sorts & sizes with or w/o nfs attachment if any, us & ur,as it is. (qty are in approx.basis)loc: lying at back side of despatch section in scrap yard judw remarks: [1] loading by purchaser[2].cutting allowed for loading purpose only.[3].cutting will be allowed after following all the fire prevention related instruction of judw depot[4]. private road crane allowed for loading purpose....

Northern Railway - Haryana

37342895 auction sale of scrap re & signaling material consisting of pillers, post, pipes, rounds, wire ropes, pullies of c.i / cast aluminium pullies, junction box with or w / o electrical fitting if any, s & t boxestia bar, rods, signaling light fitting, fire extinguisher, and other fs / nfs attachments if any, angles, trd items, signal pipes & electric poles, poles, signal post, galv. wire, mast ( trd ) , cantilever, signal post, ladder, wire ropes, lever, mast, girder, other structure, mixed with other m.s. & c.i. scrap etc of sorts & sizes with or w / o nfs attachment if any, us & ur, as it is. ( qty are in approx.basis ) loc: lying at two places: 1. lying at bin no. b 13 and lying at open ground umb end in scrap yard judw remarks: [ 1 ] loading by purchaser [ 2 ] .cutting allowed for loading purpose only. [ 3 ] .cutting will be allowed after following all the fire prevention related instruction of judw depot [ 4 ] delivery will be given first from bin no.b 13 and after that from open ground umb end. [ 5 ] . private road crane allowed for loading purpose....

Northern Railway - Haryana

37015158 auction sale of scrap re & signaling material including angles, trd items, signal pipes & electric poles, poles, signal post, galv. wire, mast ( trd ) , cantilever, signal post, ladder, wire ropes, lever, mast, girder, other structure, mixed with other m.s. & c.i. scrap etc of sorts & sizes with or w / o nfs attachment if any, us & ur, as it is. ( qty are in approx.basis ) loc: lying at near bin no. b 18, umb end open ground in scrap yard judw remarks: [ 1 ] loading by purchaser [ 2 ] .cutting allowed for loading purpose only. [ 3 ] .cutting will be allowed after following all the fire prevention related instruction of judw depot [ 4 ] . private road crane allowed for loading purpose....

Northern Railway - Haryana

36881764 auction sale of scrap re & signaling material including angles, trd items, signal pipes & electric poles, poles, signal post, galv. wire, mast ( trd ) , cantilever, signal post, ladder, wire ropes, lever, mast, girder, other structure, mixed with other m.s. & c.i. scrap etc of sorts & sizes with or w / o nfs attachment if any, us & ur, as it is. ( qty are in approx.basis ) loc: lying at near bin no. b 18, umb end open ground in scrap yard judw remarks: [ 1 ] loading by purchaser [ 2 ] .cutting allowed for loading purpose only. [ 3 ] .cutting will be allowed after following all the fire prevention related instruction of judw depot [ 4 ] . private road crane allowed for loading purpose....

Northern Railway - Haryana

36446853 auction sale of scrap re & signaling material including angles, trd items, signal pipes & electric poles, poles, signal post, galv. wire, mast ( trd ) , cantilever, signal post, ladder, sign board, junction box, lamps, wire ropes, lever, mast, girder, other structure, mixed with other m.s. & c.i. scrap etc of sorts & sizes with or w / o nfs attachment if any, us & ur, as it is. ( qty are in approx.basis ) loc: lying at in front of sh guru ravidas mandir in scrap yard judw remarks: [ 1 ] loading by purchaser [ 2 ] .cutting allowed forloading purpose only. [ 3 ] .cutting will be allowed after following all the fire prevention related instruction of judw depot [ 4 ] . private road crane allowed for loading purpose....

Northern Railway - Haryana

36361511 auction sale of scrap re & signaling material including angles, cast iron block, signal pipes & electric poles, poles, signal post, w. rope, rly line pcs, mast ( trd ) , cantilever, signal post, ladder, sign board, junction box, pullies, lamps, signaly lever, mast, signal rod of different types.girder, other structure, mixed with other m.s. & c.i. scrap, electric wire of different types etc of sorts & sizes with or w / o nfs attachment us & ur.as it is. ( qty are in approx.basis ) remarks: [ 1 ] loading by purchaser [ 2 ] .cutting allowed for loading purpose only. [ 3 ] .cutting will be allowed after following all the fire prevention related instruction of judw depot...

Municipal Corporation - Haryana

36258427 bids are invited for providing and placing of godrej furniture modular conference table , cantilever conference chair , high back conference chair , medium back conference chai total quantity : 216...

Northern Railway - Haryana

36119027 auction sale of scrap re & signaling material including angles, trd items, signal pipes & electric poles, poles, signal post, galv. wire, mast ( trd ) , cantilever, signal post, ladder, sign board, junction box, lamps, wire ropes, lever, mast, girder, other structure, mixed with other m.s. & c.i. scrap etc of sorts & sizes with or w / o nfs attachment if any, us & ur, as it is. ( qty are in approx.basis ) loc: lying at back side of dispatch section in scrap yard judw remarks: [ 1 ] loading by purchaser [ 2 ] .cutting allowed forloading purpose only. [ 3 ] .cutting will be allowed after following all the fire prevention related instruction of judw depot...

Indian Oil Corporation Limited - Haryana

35875461 design, engineering, supply, fabrication, installation and construction of cantilever car parking sheds integrated with solar panel roof along with successfully testing and commissioning of solar plant system at panipat refinery, iocl....

Northern Railway - Haryana

35872005 auction sale of scrap re & signaling material including angles, trd items, signal pipes & electric poles, poles, signal post, galv. wire, mast ( trd ) , cantilever, signal post, ladder, sign board, junction box, pullies, lamps, wire ropes, lever, mast, girder, other structure, mixed with other m.s. & c.i. scrap etc of sorts & sizes with or w / o attachment if any, us & ur, as it is. ( qty are in approx.basis ) remarks: [ 1 ] loading by purchaser [ 2 ] .cutting allowed forloading purpose only. [ 3 ] .cutting will be allowed after following all the fire prevention related instruction of judw depot [ 4 ] non ferrous items will be taken back if found in lot at the time of delivery....

Indian Oil Corporation Limited - Haryana

35706324 civil repair jobs for warehouse and accessibility on bcr roof at pta terminal, ppmc civil repair jobs for warehouse rcc columns, cantilever roof, battery charging room and for provision of accessibility on bcr roof at pta terminal, ppmc...

Northern Railway - Haryana

35215073 auction sale of scrap re & signaling material including angles, cast iron block, signal pipes & electric poles, poles, signal post, , mast ( trd ) , cantilever, signal post, ladder, sign board, junction box, pullies, lamps, signaly lever, mast, signal rod of different types.girder, other structure, mixed with other m.s. & c.i. scrap etc of sorts & sizes with or w / o attachment us & ur.as it is. ( qty are in approx.basis ) remarks: [ 1 ] loading by purchaser [ 2 ] .cutting allowed for loading purpose only. [ 3 ] .cutting will be allowed after following all the fire prevention related instruction of judw depot [ 4 ] non ferrous items will be taken back if found in lot at the time of delivery....

Department Of Irrigation - Haryana

35186076 tender for extension of gangwani minor from rd.22000 40200 demolishing rcc work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 meters lead as per direction of engineer in charge( hsr item no. 5.25) 2 demolishing cement concrete manually/ by mechanical means including disposal of material within 50m lead as per direction of engineer in charge nominal concrete 1 :2:4 or leaner mix (i/c equivalent cumdesign mix) (hsr no. 5.23.2). 3 demolishing brick masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50m lead as perdirection of engineer in charge in cement mortar ( hsr item no. 5.7.4) 4 extra for leveling & neatly dressing of disposal soil completely (hsr no. 4.6). 5 earth work in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5m, as directed by engineer in charge all kind of soil ( hsr item no. 4.12.1) 6 earth work in excavation by mechanical means (hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m all kind of soil (hsr no. 4.14.1). 7 earth work in excavation by mechanical means (hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m, as directed by engineer in chargewith lead of 180 mtr all kind of soil (hsr no. 4.12.1+3.1.2). 8 extra compactions for laying earth/fly ash as per specifications in 20 cm layers and dressing with cost of rolling and extra for watering the earth/fly ash laid in 20 cm layers as per specifications all kind of soil (hsr no.17.8.1+17.8.3+17.8.2) 9 providing and laying in position ready mixed plain cement concrete with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agigated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of r.m.c from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per is : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the engineer in charge. (note: less cement used as per design mix is recoverable. however no extra payment shall be made if excess cement is used as per design mix): all works upto plinth level :m 15 grade plain cement concrete cum (cement content considered @ 240 kg/cum) (hsr no. 6.22.2.2). 10 providing and laying in position machine batched and machine mixed design mix m 25 grade cement concrete for reinforced concrete works, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the engineer in charge. (note : cement content considered in this item is @330 kg/cum. less cement used as per design mix is recoverable. however no extra payment shall be made if excess cement is used as per design mix) :all works upto plinth level (hsr no.6.25.1) 11 providing and laying in position machine batched and machine mixed design mix m 25 grade cement concrete for reinforced concrete works, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per is : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the engineer in charge. (note : cement content considered in this item is @330 kg/cum. less cement used as per design mix is recoverable. however no extra payment shall be made if excess cement is used as per design mix) :all works above plinth level up to floor iv level (hsr no. 6.25.2) 12 centering and shuttering including strutting, propping etc. and removal of form work for : foundations, footings, bases for columns (hsr no. 6.29.1). 13 centering and shuttering including strutting, propping etc. and removal of form work for :lintels, beams, plinth beams, girders, bressumers and cantilevers (hsr no. 6.30.5). 14 centering and shuttering including strutting, propping etc. and removal of form work for : columns, pillars, piers, abutments, posts, struts (hsr no. 6.29.3). 15 providing and laying of brick on edge flooring with bricks of class designation 7.5 on a bed of 12 mm cement mortar, including filling the jointsmortar, with common burnt clay non modular bricks: 1:6 (1cement : 6 coarse sand) (hsr no. 10.33.2). 16 providing and fixing in position 20mm thick premoulded joint filler in expansion joint for fixed ends of simply supported spans not exeeding 10m to cater for a horizontal movement upto 20mm, covered with sealant complete as per drawing and mort&h specifications (hsr no. 27.51.3). 17 painting two coats on new concrete surfaces:painting two coats after filling the surface with synthetic enamel paint on new plastered concrete surfaces (hsr no. 34.49). 18 sign board (n.s.) 19 steel reinforcement for r.c.c work where not include in the complete rate of r.c.c, including straightening, cutting, bending, placing in position, binding wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect (note: reinforcement shall be measured in length including hooks, if any, seperately for different diameters as actually used in work, excluding overlaps. wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of bindings & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement).:thermo mechanically treated bars of grade fe 500d (hsr no. 6.33.6.1 or 6.34.6). 20 providing weep holes in brick masonary/plain/ reinforced concrete abutment, wing wall/ return wall with 100 mm dia ac pip, extending through the full width of the structure with slope of 1v:20h towards drawing force. complete as per drawing and mort&h specifications (hsr no. 27.15). 21 10 mm thick 1:3 cement plaster hsr item no.11.4.2). 22 lining with design mix concrete of grade m 15 with minimum cement content 240kg/cum, 75mm thick in curve portion and bed manually i/c rendering with cement sand (1:3) slurry, form work, dressing and preparation of sub grade as per directions of engineer in charge bending and fixing iron rungs in lined slopes. on bed 75mm thickness in slope (hsr item no.14.10.1.1.1 hsr 14.13) excluding cement sand slurry 1:3 23 lining with design mix concrete of grade m 15 with minimum cement content 240kg/cum, 75mm thick in curve portion and bed manually i/c rendering with cement sand (1:3) slurry, form work, dressing and preparation of sub grade as per directions of engineer in charge bending and fixing iron rungs in lined slopes. on side slope bed 75mm thickness in slope (hsr item no.14.10.1.2.1 hsr 14.13) excluding cement sand slurry 1:3 24 brick work with common burnt clay non modular bricks of class designation 7.5 in foundation and plinth in: cement mortar 1:6 (1 cement : 6 coarse sand) (sleeper underneath) (hsr no. 7.21.2). 25 filling expansion joint with special imperivious hot pour 12.5 mm wide (hsr no. 14.18). 26 boundary pillar reinforced cement concrete m 15 grade boundary pillars of standard design as per irc:25 1967, fixed in position including finishing and lettering but excluding painting (hsr no. 34.28). 27 kilometre stone ( rd stone)reinforced cement concrete m25 grade kilometre stone of standard design as per irc:8 1980,fixing in position including painting and printing etc complete as per technical clause 804 of morth specifications (hsr no. 34.27.2). 28 credit for old steel 29 credit for old bricks 30 earth work for lip cutting for lining of irrigation channels, inclusive of all allowances, lead and dressing by mechanical/ mannual means: 0 to 1.5m depth. hsr no.14.24.1 ...

Northern Railway - Haryana

35107317 auction sale of scrap re & signaling material including angles, cast iron block, signal pipes & electric poles, poles, signal post, w. rope, mast ( trd ) , cantilever, signal post, ladder, sign board, junction box, pullies, lamps, signaly lever, mast, signal rod of different types.girder, other structure, mixed with other m.s. & c.i. scrap etc of sorts & sizes with or w / o attachment us & ur.as it is. ( qty are in approx.basis ) loc: lying back side of dispatch section in scrap yard judw. remarks: [ 1 ] loading by purchaser [ 2 ] .cutting allowed for loading purpose only. [ 3 ] .cutting will be allowed after following all the fire prevention related instruction of judw depot [ 4 ] non ferrous items will be taken back if found in lot at the time of delivery....

Kaithal Cooperative Sugar Mills Limited - Haryana

35077841 tender for extension of pa to md office. ( civil work ) 1.01 earth work in excavation by mechanical means ( hydraulic excavator ) / manual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 sqm on plan ) , including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 50 cum 1.02 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work below plinth level and up to floor iv level : 6.1.6 ) 1:4:8 ( 1 cement : 4 coarse sand ( zone iii ) : 8 graded stone aggregate 40 mm nominal size ) 3.9 cum 1.03 centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns, etc. for mass concrete 10 sqm 1.04 suspended floors, roofs, landings, balconies 10 sqm 1.05 lintels, beams, plinth beams, girders, and cantilevers 10 sqm 1.06 providing and laying damp proof course with cement concrete 1:1:2: 4 ( 1 cement : 1.5 coarse sand ( zone iii ) : 3 graded stone aggregate 20 mm nominal size ) 40 mm thick 2 sqm 1.07 brick work with common burnt clay non modular bricks of class designation 12.5 in foundation and plinth in : cement mortar 1:6 ( 1 cement: 6 coarse sand ) ( derived rate ) ( 7.40 7.39 ) 5 cum 1.08 brick work with common burnt clay nonmodular bricks of class designation 12.5 in super structure above plinth level up to floor four level in all shapes and sizes in : cement mortar 1:6. 8 cum 1.09 half brick masonry with common burnt clay non modular bricks of class designation 7 .5 in superstructure above plinth level up to floor iv level. cement mortar 1 :4 ( 1 cement :4 coarse sand ) 1.1 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level , excluding the cost of centering, shuttering, finishing and reinforcement with 1 :1.5:3 ( 1 cement coarse sand ( zone 111 ) : 3 graded stone aggregate 20 mm nominal size ) . 7 cum 1.11 15 mm thick cement plaster on the rough side of single or half brick wall of mix. cement mortar 1:6 ( 1 cement : 6 fine sand ) 38 sqm 1.12 12mm thick cement plaster of mix 1:6 on the brick wall 1:6 ( 1cement : 6 fine sand ) 38 sqm 1.13 providing and laying of base course of floors consisting of 100 mm thick cement 1 :8 :16 and 100 mm sand or stone filling re compacting excavated soil in plinth under floors, including watering, ramming, consolidating and dressing complete 17 sqm 1.14 painting top of roofs with bitumen of approved quality @ 17 kg per 10 sqm impregnated with a coat of coarse sand at 60 cudm per 10 sqm, including cleaning the slab surface with brushes and finally with a piece of cloth lightly soaked in kwrosene oil complete with residual type petroleum bitumen of grade vg io 17 sqm 1.15 10 cm thick ( average ) mud phaska of damped brick earth on roofs laid to slope consolidated and plastered with 25 mm thick mud mortar mixed with bhusa @ 35 kg per cum of earth and gobri leaping with mix 1:1 ( 1 clay : 1 cow dung ) and covered with flat tiles bricks, grouted with cement mortar 1:3 ( 1 cement: 3 fine sand ) mixed with 2 % of integral water proofing compound by weight of cement and finished neat : with common burnt clay non modular brick tile of class sqm designation 12.50 17 sqm 1.16 providing & fixing on wall face unplasticised rigid pvc rain water pipe conforming to is : 13592b type a, including jointing with seal ring conforming to is : 5382, 10 mm gap for thermal expansion, ( i ) single sockted pipes. 110mm diameter 6 rmtr. 1.17 providing & fixing on wall face unplasticised rigid pvc moulded fittings / accessories for unplasticised rigid rain water pipes conforming to is : 13592 type a, including jointing with seal ring conforming to is : 5382, 10 mm gap for thermal expansion. pipes. bend 87.5 degree 110 mm bend 4 each . 10 1.18 wall painting on a cement plaster surface with acrylic emulsion paint of approved brand and manufacture to give an even shade .two or more coats on new work 38 sqm 1.19 distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: new work ( two or more coats ) over and including water thinnable priming coat with cement primer 38 sqm 1.2 providing gola 75x75 mm in cement concrete 1:2:4 ( 1 cement:2 coarse sand : 4 stone aggregate 10 mm and down gauge ) , including finishing with cement mortar 1:3 ( 1 cement: 3 fine sand ) as per standard design : in 75x75 mm deep chase. 10 mtr. 1.21 making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 ( 1 cement :2 coarse sand :4 graded stone aggregate of 20 mm nominal size ) over p.v.c. sheet 1 mx 1 m x 400 micron, finished with 12 mm cement plaster 1:3 ( 1 cement: 3 coarse sand ) and a coat of neat cement, rounding the edges and making finishing the outlet complete . 2 each 1.22 dismantling stone slab roofing over wooden karries or r.c.c. cum battens ( dismantling karries and battens to be paid for separately ) , including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. 17 cum 1.23 demolishing brick work manually / by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge 5 cum 1.24 steel reinforcement for r.c.c. work, where not included in the complete rate of rcc, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect note: reinforcement shall be measured in length including hooks, if any, separately for different diameters as actually used in work , excluding overlaps. wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement . thermo mechanically treated bars of grade fe 500d or more 275 kg. 11 1.25 painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. 18.2 sqm 1.26 applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping etc. 18.2 sqm 1.27 providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows ( area of opening for panel inserts excluding portion inside grooves or rebates to be measured ) . panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick: kiln seasoned and chemically treated hollock wood 1.5 sqm 1.28 providing & fixing in place door frame of section 170x58mm metre made of gpsp sheet ( is277 ) constructed from sheet thickness 1.2mm with a single rebate of 58mm duly filled with puf and finished with powder coating in regular ral shades as desired by engineer incharge . frame should be coated with pure polyester / epoxy polyester powder coating having thickness of 60 80 micron and provided with 3mm thick hinge enforcement plates....

Food Corporation Of India - Haryana

34851174 tender for annual repair and maintenance of and misc. repair works at bg narwana earth work in excavation by mechanical means ( hydraulic excavator ) / manual means over areas ( exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan ) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by engineer incharge:all kinds of soil 2 providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering all work up to plinth level : 1:5:10 ( 1 cement : 5 fine sand derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources ) 3 centering and shuttering including strutting, propping etc. and removal of form forlintels, beams, plinth beams, girders, bressumers and cantilevers 4 providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement all work up to plinth level : 1:1.5:3 ( 1 cement : 1.5 coarse sand 5 reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 ( 1 cement : 1.5 coarse sand ( zone iii ) : 3 graded stone aggregate 20 mm nominal size ) . 6 steel reinforcement for r.c.c. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level cold twisted bars 7 structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. 8 brick work with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in foundation and plinth in:cement mortar 1:6 ( 1 cement : 6 coarse sand ) 9 brick work with common burnt clay f.p.s. ( non modular ) bricks of class designation 7.5 in superstructure above plinth level up to floor v level in all shapes and sizes in :cement mortar 1:6 ( 1 cement : 6 coarse sand ) 10 15 mm cement plaster: 1:6 ( 1 cement : 6 fine sand ) 11 excavating, supplying and filling of local earth ( including royalty ) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. 12 clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared. 13 demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of engineer in charge. nominal concrete 1:3:6 or richer mix ( i / c equivalent design mix ) 14 dismantling roofing including ridges, hips, valleys and gutters etc., and stacking the material within 50 metres lead of: asbestos cement sheet 15 taking out wind ties from roof including cutting out rusted bolts, nuts etc. and removing materials to any distance within compound and stacking. 16 providing and fixing precoated galvanised iron profile sheets ( size, shape and pitch of corrugation as approved by engineer in charge ) 0.50 mm ( + 0.05 % ) total coated thickness with zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns. sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by engineer in charge. the sheet shall be fixed using self drilling / self tapping screws of size ( 5.5x 55 mm ) with epdm seal, complete upto any pitch in horizontal / vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. 17 providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm ( +0.05 % ) total coated thickness, zinc coating 120 grams per sqm as per is: 277, in 240 mpa steel grade, 5 7 microns epoxy primer on both side of the sheet and polyester top coat 15 18 microns using self drilling / self tapping screws complete :ridges plain ( 500 600mm ) 18 providing gola 75x75 mm in cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge ) , including finishing with cement mortar 1:3 ( 1 cement : 3 fine sand ) as per standard design :in 75x75 mm deep chase 19 fixing of old wind tie with new fittings including painting two or more coats with anticorrosive bitumastic paint of approved brand & manufacturer over and including priming coat of ready mixed zinc chromate yellow primer of approved brand. 20 taking out doors, windows and clerestory window shutters ( steel or wood ) including stacking within 50 metres lead :of area beyond 3 sq. metres 21 supplying and fixing rolling shutters of approved make, made of required size m.s. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to is: 4454 part 1 and m.s. top cover of required thickness for rolling shutters.80x1.20 mm m.s. laths with 1.20 mm thick top cover 22 cement concrete flooring 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate ) finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete. 40 mm thick with 20 mm nominal size stone aggregate 23 providing and laying 60mm thick faciory made cement concrete interlocking paver block of m 30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of engineer in charge. 24 providing and laying at or near ground level factory made kerb stone of m 25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 ( 1 cement: 3 coarse sand ) , including making joints with or without grooves ( thickness of joints except at sharp curve shall not to more than 5mm ) , including making drainage opening wherever required complete etc. as per direction of engineer in charge ( length of finished kerb edging shall be measured for payment ) . ( precast c.c. kerb stone shall be approved by engineer in charge ) . 25 dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. 26 12 mm cement plaster of mix : 1:6 ( 1 cement: 6 fine sand ) 27 removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete 28 white washing with lime to give an even shade : old work ( two or more coats ) 29 colour washing with lime to give an even shade : old work ( one or more coats ) 30 finishing walls with water proofing cement paint of required shade : old work ( one or more coats @ 2.20 kg / 10 sqm ) complete. 31 providing and laying cement concrete in retaining walls, return walls, walls ( any thickness ) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing:1:2:4 ( 1 cement : 2 coarse sand ( zone iii ) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources ) ...

Northern Railway - Haryana

34645903 auction sale of scrap re & signaling material including angles, signal pipes & electric poles, poles, signal post, w. rope, mast ( trd ) , cantilever, signal post, ladder, sign board, junction box, pullies, lamps, signaly lever, mast, signal rod of different types.girder, other structure, mixed with other m.s. & c.i. scrap etc of sorts & sizes with or w / o attachment us & ur.as it is. ( qty are in approx.basis ) remarks: [ 1 ] loading by purchaserloc: lying at back side of b 09, b 10 and back side of b 11 under electric tower in scrap yard judw. [ 2 ] .cutting allowed forloading purpose only. [ 3 ] .cutting will be allowed after following all the fire prevention related instruction of judw depot [ 4 ] non ferrous items will be taken back if found in lot at the time of delivery....

Northern Railway - Haryana

34511085 auction sale of scrap re & signaling material including angles, signal pipes & electric poles, poles, signal post, w. rope, mast ( trd ) , cantilever, signal post, ladder, sign board, junction box, pullies, lamps, signal lever, mast, signal rod of different types.girder, other structure, mixed with other m.s. & c.i. scrap etc of sorts & sizes with or w / o attachment us & ur.as it is. ( qty are in approx.basis ) remarks: [ 1 ] loading by purchaser [ 2 ] .cutting allowed forloading purpose only. [ 3 ] .cutting will be allowed after following all the fire prevention related instruction of judw depot [ 4 ] non ferrous items will be taken back if found in lot at the time of delivery....

Northern Railway - Haryana

34408777 auction sale of scrap re & signaling material including angles, signal pipes & electric poles, poles, signal post, w. rope, mast ( trd ) , cantilever, signal post, ladder, sign board, junction box, pullies, lamps, signaly lever, mast, signal rod of different types.girder, other structure, mixed with other m.s. & c.i. scrap etc of sorts & sizes with or w / o attachment us & ur.as it is. ( qty are in approx.basis ) remarks: [ 1 ] loading by purchaser [ 2 ] .cutting allowed forloading purpose only. [ 3 ] .cutting will be allowed after following all the fire prevention related instruction of judw depot [ 4 ] non ferrous items will be taken back if found in lot at the time of delivery....

Indian Oil Corporation Limited - Haryana

34315931 design, engineering, supply, fabrication, installation and construction of cantilever car parking sheds integrated with solar panel roof along with successfully testing and commissioning of solar plant system at panipat refinery...

Northern Railway - Haryana

33897819 auction sale of scrap re & signaling material including angles, signal pipes & electric poles, poles, signal post, galv. wire, mast ( trd ) , cantilever, signal post, ladder, sign board, junction box, pullies, lamps, wire ropes, lever, mast, girder, other structure, mixed with other m.s. & c.i. scrap etc of sorts & sizes with or w / o attachment us & ur.as it is. ( qty are in approx.basis ) remarks: [ 1 ] loading by purchaser [ 2 ] .cutting allowed forloading purpose only. [ 3 ] .cutting will be allowed after following all the fire prevention related instruction of judw depot [ 4 ] non ferrous items will be taken back if found in lot at the time of delivery....

Urban Local Bodies - Haryana

33598050 providing and fixing of children play equipments in 3 b officer colony park, nit faridabad sea saw ( 4seater ) : 8’l x 5’.5w x 15’ high. frame is of m.s. pipe 2’ x 12 gauge. sitting planks is of m.s. pipe 2’’ x 12 gauge and its cantilever & handles is of m.s. pipe ¾’ x 12 gauge. sitting seats 4 nos. is of molded frp material in 3mm thick with suitable pu primer & pu paints. complete item with gst, transportation, installation with c.c & labor at site. @ 16200 / per each 2 chain swing ( 2seater ) : 10’l x 6’w x 8’.5 h. horizontal frame and vertical legs is of m.s. pipe 2’’ x 12 gauge. it stays with m.s. pipe 1’’ x 12 gauge. swinging seats 2nos is of frp molded seat of 2mm thick fitted with m.s. pipe ½’’ frame x 12 gaugewhich hang with m.s. chain 6mm thick duly plated with ball bearing & m.s. flat 6mm thick housing. complete with priming and enamel spray painting in multi colors @ 21000 / per each 3 bridge ladder: 10’l x 2’w x 6’h. horizontal ladder is of m.s. pipe 2”, ¾” & vertical ladder is of same material of 12 gauge isi mark with suitable pu primer & pu paints. complete item with gst, transportation, installation with c.c & labor at site. @ 21000 / per each 4 multi activity play station covering area: 34’l x 22’w it contains: frp spiral slide 6mm thick inclined at 5’h – 1 no frp tube slide inclined at 5’h – 1 no frp wave slide 6mm thick inclined at 5h 1 no frp bowl slide 6mm thick with frp entry gate inclined at 3’h – 1 no frp stair 3mm thick inclined at 3’h 1 no. frp platform hex. shape 5mm thick in 7’dia – 2 no. frp canopy – 2 no. frp deer figure on canopy – 2no. frp fancy railing frog & monkey shape – 4 no. frp walking bridge 7.5’ long – 1 no. m.s. spring climber – 1 no. m.s. zig zag climber – 1 no m.s. chain net climber – 1 no m.s. climbing ladder – 1 no m.s. station in which vertical m.s. pipe is of 3” x12g ofi.s.i mark – 2 no complete item with gst, transportation, installation with c.c & amp; labor at site. @ 5, 70, 000 / per each 5 wave slide: 9’.5 l x 5’h. wave slide is of molded fiberglass reinforced plastic ( frp ) of 6mm thick and climbing ladder is of m.s. pipe 1’’ x 12 gauge & m.s. rectangular pipe 65 x 25 mm box x 16 gauge as climbing steps which support with 1’’.25 sq. pipe x 16 gauge. complete with priming & painting in multi colors.@ 35400 / per each 6 merry go round ( 4 seater ) : 5’ dia. main frame is of m.s. sq. pipe 2’’ x 2’’ x 14 g and having suitable handle & foot rest is of round pipe ¾’’ x 12 gauge. central pipe is of m.s. pipe 3’’’x 12 g with heavy duty shaft 50mm thick & ball bearing assembly. it consists of 4no chair made of molded frp plastic. complete with priming and painting in multi colors. @ 39500 / per each...

Indian Oil Corporation Limited - Haryana

33297643 design, engineering, supply, fabrication, installation and construction of cantilever car parking sheds integrated with solar panel roof along with successfully testing & commissioning of solar plant system at panipat refinery, iocl...

Urban Local Bodies - Haryana

32844189 providing and fixing of children play equipments in 3 b officer colony park, nit faridabad 1 sea saw ( 4seater ) : 8’l x 5’.5w x 15’ high. frame is of m.s. pipe 2’ x 12 gauge. sitting planks is of m.s. pipe 2’’ x 12 gauge and its cantilever & handles is of m.s. pipe ¾’ x 12 gauge. sitting seats 4 nos. is of molded frp material in 3mm thick with suitable pu primer & pu paints. complete item with gst, transportation, installation with c.c & labor at site. @ 16200 / per each 2 chain swing ( 2seater ) : 10’l x 6’w x 8’.5 h. horizontal frame and vertical legs is of m.s. pipe 2’’ x 12 gauge. it stays with m.s. pipe 1’’ x 12 gauge. swinging seats 2nos is of frp molded seat of 2mm thick fitted with m.s. pipe ½’’ frame x 12 gaugewhich hang with m.s. chain 6mm thick duly plated with ball bearing & m.s. flat 6mm thick housing. complete with priming and enamel spray painting in multi colors @ 21000 / per each 3 bridge ladder: 10’l x 2’w x 6’h. horizontal ladder is of m.s. pipe 2”, ¾” & vertical ladder is of same material of 12 gauge isi mark with suitable pu primer & pu paints. complete item with gst, transportation, installation with c.c & labor at site. @ 21000 / per each 4 multi activity play station covering area: 34’l x 22’w it contains: frp spiral slide 6mm thick inclined at 5’h – 1 no frp tube slide inclined at 5’h – 1 no frp wave slide 6mm thick inclined at 5h 1 no frp bowl slide 6mm thick with frp entry gate inclined at 3’h – 1 no frp stair 3mm thick inclined at 3’h 1 no. frp platform hex. shape 5mm thick in 7’dia – 2 no. frp canopy – 2 no. frp deer figure on canopy – 2no. frp fancy railing frog & monkey shape – 4 no. frp walking bridge 7.5’ long – 1 no. m.s. spring climber – 1 no. m.s. zig zag climber – 1 no m.s. chain net climber – 1 no m.s. climbing ladder – 1 no m.s. station in which vertical m.s. pipe is of 3” x12g ofi.s.i mark – 2 no complete item with gst, transportation, installation with c.c & amp; labor at site. @ 5, 70, 000 / per each 5 wave slide: 9’.5 l x 5’h. wave slide is of molded fiberglass reinforced plastic ( frp ) of 6mm thick and climbing ladder is of m.s. pipe 1’’ x 12 gauge & m.s. rectangular pipe 65 x 25 mm box x 16 gauge as climbing steps which support with 1’’.25 sq. pipe x 16 gauge. complete with priming & painting in multi colors.@ 35400 / per each 6 merry go round ( 4 seater ) : 5’ dia. main frame is of m.s. sq. pipe 2’’ x 2’’ x 14 g and having suitable handle & foot rest is of round pipe ¾’’ x 12 gauge. central pipe is of m.s. pipe 3’’’x 12 g with heavy duty shaft 50mm thick & ball bearing assembly. it consists of 4no chair made of molded frp plastic. complete with priming and painting in multi colors. @ 39500 / per each...

Northern Railway - Haryana

32727578 auction sale of scrap re & signaling material including angles,rail pcs, signal pipes & electric poles, poles,signal post,galv. wire, mast (trd),cantilever,signal post, ladder, sign board, junction box, pullies, lamps,wire ropes, lever,mast, girder,other structure, mixed with other m.s. & c.i. scrap etc of sorts & sizes with or w/o attachment us & ur. (qty are in approx.basis) remarks: [1] loading by purchaser[3].cutting will be allowed after following all the fire prevention related instruction of judw depot...

Public Works Department - Haryana

32099548 providing and fixing overhead cantilever and providing and fixing overhead cantilever and gantry boards for compliance of road safety on saharanpur kurukshetra pehowa cheeka road ( sh 06 ) in district kurukshetra....

Public Works Department - Haryana

31967540 providing, supplying, fixing of furniture for excise and taxation building, sector 32 in gurugram district. 1 jetc / detc cabin furniturecabin table ( 2400x2280x750mm ) supplying and placing in position main table with overall size of 2400x2280x750mm and with following specifications. top surface of the table shall of size w2400 x d1080mm and made up of 70mm thick mdf ( medium density fibre ) board duly finished with 4mm natural veneer and final coating of pu. table top with 18mm thick half round teak wood beadig on all edge sides of table top of giving premium aesthetic. leg of the table for supporting table top shall be made up of 50mm mdf board which shall also be duly finished with 4mm natural veener and pu coating. the front modesty panel of the table shall be made up of 18mm thikc mdf board which shall also be duly finished with veener and pu coating. main table top with black leather pad. for personal storage one mobile pedestal ( 3 drawer unit ) shall be provided of size 510 mm width x 635 mm height and 445 mm depth. the storage pedestal shall also be made up of 18mm thick mdf duly finished with 4mm natural veener & final coating of pu. the side storage shall be of size 1200mm width x 445mm depth x 645 mm height. the side unit shall be made up of 18mm thick mdf board duly finshed with 4mm natural veneer and final finish by pu coating. the side unit shall contain open space for keeping cpu , one closed storage shutter& open space in the middle with one shelf for keeping files. the thickness of the top of the side unit shall be 25mm. the hardness of the pu coating shall be 1.5h. ( color shall be oxford cherry and black ) . 2 main chair providing and supplying high back chair with ergonomic design, comfortable & aesthetically appealing. the seat shall be made of 15mm thick hot pressed commercial plywood upholstered with high resilience moulded polyurethane foam 40mm thick having density 40kg / m³ with foam net tapestry 0.6mm thick and 300 gsm and the back shall be made of polypropylene net cover upholstered with breathable mesh tapestry. the seat shall be supplied with adjustable sliding type and the backrest shall be made by keeping the natural curvature of the spine which helps to provide full back support as well as head support. the chair shall be supplied with black integral adjustable polyurethane arm. for seating durability the chair shall have synchro knee tilt 360 degree revolving mechanism having four position locking and tilt tension adjustment with anti shock feature which provides back strength for the chair. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standards. the pedestal should have five legged ms crca chrome plated having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors which shall be made of injection moulded black nylon 30% glass filled, confirming to ansi / bifma x5.1 2011 tested to perform 98, 000 cycles with 250lbs load. the seat size shall be 510±10 mm ( w ) x 500±10 mm ( d ) and back size shall be 530±10 ( w ) x 685±10 mm ( h ) from seat & overall height = 1150±10 mm, base width / depth = 760±10 mm. ( color : black ) 3 visitor chairproviding and supplying visitor chair with ergonomically designed. the seat and back shall be made up of 15mm and 12mm thick hot pressed commercial plywood padded with high resilience polyurethane foam 40mm thick having density 40kg / m³ in seat and 25mm thick having density 32kg / m³ in back. the same shall be upholstered with fabric tapestry 0.6mm thick and 235 gsm. the seat and back shall be arrested together with metal frame and the armrest shall be used wooden arm mounted on chrome plated pipe frame completely joint with seat and back. the frame structure shall be cantilever supported type made up of ms / crca chrome plated round pipe of dia 25.4mm with 2mm thick. there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 425±10 mm ( d ) x 430±10 mm ( w ) and back size shall be 430±10 mm ( w ) x 450±10 mm ( h ) from seat. overall height shall be = 885±10 mm, overall depth = 600±10 mm & overall width = 540±10 mm. ( color : black ) 4 2 seater sofasupplying and placing two seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. the thickness of the wood should allow for the heavy tension webbing. the sofa shall have spring attached and also be padded separately. the frame shall be padded with high resilience polyurethane foam having density 40kg / m³ in seat and having density 32kg / m³ in back. there shall be cushion arm provided padded with high resilience polyurethane foam thick having density 32kg / m³. ss strip shall be provided on front of the arm having length 515mm with cross section area 14mm x 4mm. the structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 gsm. the understructure shall have shiny chrome finish ss leg with height 100mm and 10mm thick. there shall be shoe provided at the bottom to avoid scratches on the floor. the seat size shall be 500±10 mm ( d ) x 1015±10 mm ( w ) , seat height = 430±10 mm, overall width = 1160±10 mm, overall depth = 750±10 mm & overall height = 700±10 mm. ( color : maroon ) 5 1 seater sofasupplying and placing single seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. the thickness of the wood should allow for the heavy tension webbing. the sofa shall have spring attached and also be padded separately. the frame shall be padded with high resilience polyurethane foam having density 40kg / m³ in seat and 32kg / m³ in back. there shall be cushion arm provided padded with high resilience polyurethane foam having density 32kg / m³. ss strip shall be provided on front of the arm having length 515mm with cross section area 14mm x 4mm. the structure shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 gsm. the understructure shall have shiny chrome finish ss leg with length 100mm and 10mm thick. there shall be shoe provided at the bottom to avoid scratches on the floor. the seat size shall be 500±10 mm ( d ) x 545±10 mm ( w ) , seat height = 430±10 mm, overall width = 690±10 mm, overall depth = 750±10 mm & overall height = 700±10 mm. ( color : maroon ) 6 center table supplying & placing center table with an overall size 1200mm x 600mm x 450mm. the top of the table shall be made up of 12mm thick toughened glass with bevelled edges. the profile shall be in rectangle shape with round corner. the top shall be supported on ms chrome plated tubular frame with cross section area 40mm x 20mm with 1.6mm thick. the under structure shall consist of four legs made of ms chrome plated oval pipe having cross section area 52mm x 26mm with 1.6mm thick. there shall be co polymer polypropylene shoe provided at the bottom to avoid scratches on the floor. 7 corner table supplying & placing center table with an overall size 600mm x 600mm x 450mm. the top of the table shall be made up of 12mm thick toughened glass. the top profile shall be in square shape with round corner and the edges shall be in chamfer shape. the top shall be supported on ms chrome plated oval frame with cross section area 40mm x 20mm with 1.6mm thick. the under structure shall consist of four legs made of ms chrome plated oval pipe having cross section area 52mm x 26mm with 1.6mm thick. there shall be co polymer polypropylene shoe provided at the bottom to avoid scratches on the floor. 8 back unitsupplying and placing in position back unit of the following specifications overall size of the back unit shall be 2400 w mm x 500 d mm x 1800 h mm. back unit made of mdf ( medium density fibre ) board duly finished with 4mm natural veneer and final coating of pu matching with table. back unit shall have slide storage unit upto 750mm and open shelf and openable shutter storage and shutters shall have a soft closing & antislammechanism. handles shall be provided for ease of opening. storage shall be provided with lock for security. ( color shall be oxford cherry and black ) . 9 waiting area 3 seater sofa supplying and placing a three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. the thickness of the wood should allow for the heavy tension webbing. the sofa shall have spring attached and also be padded separately. the frame shall be padded with high resilience polyurethane foam having density 40kg / m³ in seat and 32kg / m³ in back. there shall be cushion arm provided padded with high resilience polyurethane foam having density 40kg / m³. the complete structure shall be fully upholstered with leatherite tapestry 1±0.2 mm thick and 571 gsm. the understructure shall be supported by pipe frame leg of ss shiny chrome finish having length 875mm and height 100mm with cross section area 67mm x 13mm. there shall be shoe provided at the bottom to avoid scratches on the floor. the seat size shall be 600±10 mm ( d ) x 1810±10 mm ( w ) , seat height = 440±10 mm, overall width = 2110±10 mm, overall depth = 965±10 mm & overall height = 825±10 mm. ( color : brown ) 10 waiting area 2 seater sofa supplying and placing a two seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. the thickness of the wood should allow for the heavy tension webbing. the sofa shall have spring attached and also be padded separately. the frame shall be padded with high resilience polyurethane foam having density 40kg / m³ in seat and 32kg / m³ in back. there shall be cushion arm provided padded with high resilience polyurethane foam having density 40kg / m³. the structure shall be upholstered with leatherite tapestry 1±0.2 mm thick and 571 gsm. the understructure shall be supported by pipe frame leg of ss shiny chrome finish having length 875mm and height 100mm with cross section area 67mm x 13mm. there shall be shoe provided at the bottom to avoid scratches on the floor. the seat size shall be 600±10 mm ( d ) x 1210±10 mm ( w ) , seat height = 440±10 mm, overall width = 1510±10 mm, overall depth = 965±10 mm & overall height = 825±10 mm. ( color : brown ) 11 waiting area center tablesupplying & placing center table with an overall size 1200mm x 600mm x 450mm. the top of the table shall be made up of 12mm thick toughened glass with bevelled edges. the profile shall be in rectangle shape with round corner. the top shall be supported on ms chrome plated tubular frame with cross section area 40mm x 20mm with 1.6mm thick. the under structure shall consist of four legs made of ms chrome plated oval pipe having cross section area 52mm x 26mm with 1.6mm thick. there shall be co polymer polypropylene shoe provided at the bottom to avoid scratches on the floor. 12 jetc / detc cabin furniturecabin table supplying and placing in position main table with following specifications. top surface of the table shall be made up of 70mm thick mdf ( medium density fibre ) board duly finished with 4mm natural veneer and final coating of pu. table top with 18mm thick half round teak wood beadig on all edge sides of table top of giving premium aesthetic. leg of the table for supporting table top shall be made up of 50mm mdf board which shall also be duly finished with 4mm natural veener and pu coating. the front modesty panel of the table shall be made up of 18mm thikc mdf board which shall also be duly finished with 4mm natural veener and pu coating. main table top with black leather pad. for personal storage one mobile pedestal ( 3 drawer unit ) shall be provided of size 510 mm width x 635 mm height and 445 mm depth. the storage pedestal shall also be made up of 18mm thick mdf duly finished with 4mm natural veener & final coating of pu. the side storage shall be of size 1200mm width x 445mm depth x 645 mm height. the side unit shall be made up of 18mm thick mdf board duly finshed with 4mm natural veneer and final finish by pu coating. the side unit shall contain open space for keeping cpu , one closed storage shutter& open space in the middle with one shelf for keeping files. the thickness of the top of the side unit shall be 25mm. the hardness of the pu coating shall be 1.5h. ( color shall be oxford cherry and black ) .deputy supt. table w1500 x d750 x h750mm with side storage unit w900 x d445 x h645mm 13 aetos table w1650 x d900 x h750mm with side storage unit w900 x d445 x h645mm 14 etos table w1800 x d900 x h750mm with side storage unit w1200 x d445 x h645mm 15 main chair providing and supplying a high back chair with ergonomic design, comfortable & aesthetically appealing. the seat and back shall be made of natural wood and combination of ( 18+6 ) mm thick double layered moulded commercial plywood padded with high resilience polyurethane foam 70mm thick having density 32kg / m³ in seat and 45mm thick having density 32kg / m³ in back. the same shall be upholstered with leatherite tapestry 1mm thick and 571 gsm. the backrest shall be made by keeping the natural curvature of the spine which helps to provide lumbar support as well as head support. the chair shall be supplied with pp chrome cushion arm with leatherite covering top. for seating durability the chair shall have torsion bar 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standards. the pedestal should have five legged injection moulded polypropylene with chrome having pitch circle dia. 700 mm fitted with 5 nos. twin wheel castors. the castors of the chair should be injection moulded in black 30% glass filled nylon, confirming to ansi / bifma x5.1 2011 standards tested to perform 98, 000 cycles with 250lbs load. the seat size shall be 500±10 mm ( d ) x 535±10 mm ( w ) and back size shall be 510±10 mm ( w ) x 660±10 mm ( h ) from seat. overall height shall be = 1125±10 mm, overall depth = 700±10 mm & overall width = 660±10 mm. 16 visitor chair providing and supplying visitor chair with ergonomically designed. the seat and back shall be made up of 15mm and 12mm thick hot pressed commercial plywood padded with high resilience polyurethane foam 40mm thick having density 40kg / m³ in seat and 25mm thick having density 32kg / m³ in back. the same shall be upholstered with fabric tapestry 0.6mm thick and 235 gsm. the seat and back shall be arrested together with metal frame and the armrest shall be used wooden arm mounted on chrome plated pipe frame completely joint with seat and back. the frame structure shall be cantilever supported type made up of ms / crca chrome plated round pipe of dia 25.4mm with 2mm thick. there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 425±10 mm ( d ) x 430±10 mm ( w ) and back size shall be 430±10 mm ( w ) x 450±10 mm ( h ) from seat. overall height shall be = 885±10 mm, overall depth = 600±10 mm & overall width = 540±10 mm. 17 court roomcourt room table supplying & placing office table in completely knock down conditions with an overall size 3000mm x 1200mm x 750mm that is to be assembled at site. the worktop shall be made up of medium density fibre board with approved veneer laminate. the top panel shall be in rectangle shape with 79mm thick ( 75mm mdf + 4mm natural veneer & polyester polish ) . veneered portion of work surface shall be finish with polyester polish. the edges of the table shall be supplied with solid brass bar strips having cross section area 25mm x 5mm all around worktop. the top panel shall be supported on ms / crca rectangle pipe frame having cross section area 40mm x 20mm with 1.6mm thick. the table top shall be enclosed with flapper box on both sides for electric provision duly polished. the end wall of the table on the side shall be topped by gable end. it should be 63mm thick made up of ( 59mm mdf + 4mm natural veneer & polyester polish ) . the table shall be clad with 29mm thick ( 25mm mdf + 4mm natural veneer & polyester polish ) modesty panel which provide structural support for the table. the profile of the gable end and modesty panel shall be in linear shape with appropriate veneer surface. there shall be leveler provided with metal insert at the base to avoid scratches on the floor as well as uneven surfacing. the table shall be supplied with both side pedestal unit with an overall size 600mm x 920mm x 590mm. top, side, back, facia shall be made up of 18mm thick mdf board with approved veneer laminate. it shall have 3 nos. of drawer operated with the assistance of soft closed ball bearing channel and grooves handle for easy griping. the complete structure shall be supplied with approved veneer laminate and polyester polish accordingly. the table and pedestal have to be made in such a way that no gap should be seen in between. all the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metal. ( color shall be oxford cherry and black ) . 18 advocate tablesupplying & placing modular table in completely knock down conditions with an overall size 1800mm x 750mm x 750mm that is to be assembled at site. the top shall have the size 1800mm x 750mm made up of 18mm thick pre laminated particle board of grade ii of is 12823 with one side laminate and finish as per approved shade. the top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 0c. the top base frame shall be made of ss pipe frame having overall size 1800mm x 750mm with cross section area 40mm x 20mm. the top shall be supported on ms powder coated pipe having length 1533mm with 1 nos. and 110mm with 2 nos. the table shall be clad with 18mm thick modesty panel which provide structural support for the table. the modesty panel shall be made of 18mm thick pre laminated particle board with size 1050mm / 1000mm x 400mm. the profile of the modesty panel shall be parallelogram shape and the edges sealed with 2mm thick pvc edge banding. the table understructure shall be supported by two legs having x type frame. the legs of the table shall be made up of ms powder coated 40μ 60μ thick rectangular pipe of size 65 mm x 65mm with 2mm thick vertical structure & 65mm x 48mm with 2mm thick inclined structure. visible part of the each x frame legs to be covered with 3mm thick and 67mm width ms sheet duly finished in chrome plating from two sides. horizontal support connecting x frames should be made up of 1.2 mm thick ms powder coated pipe of dia. 40mm & length 1520mm and approx. 120mm below from the lower side of worktop. 2 supports of pipe having same dia. should be joined vertically with horizontal pipe to support of worktop. a pedestal shall be provided with an overall size 400mm x 450mm x 630mm. the pedestal shall be made up of pre laminated particle board of grade ii of is 12823. pedestal side, back, facia shall be 18mm thick and drawer base 9mm thick and top 25mm thick. the pedestal shall have 3 nos. of drawer have same size 357mm x 172mm. the drawer shall be operated with ball bearing base telescopic channel having load capacity 35kg to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be locked with one single key. the pedestal shall be mounted on injection moulded nylon castor. ( color shall be oxford cherry and black ) . 19 steno / reader tablesupplying & placing executive table with credenza unit and pedestal unit in completely knock down conditions with an overall size 1500mm x 750mm x 750mm that is to be assembled at site. the construction of the main table shall be free standing structure constructed with the help of minifix dowels and pins. the worktop shall have the size 1500mm x 750mm made up of 50mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be enclosed with wire manager cap for electric provision. the table top shall be supported on particle board base gable end. the end wall of the table on the side shall be topped by gable end. it should be made up of 25mm thick pre laminated particle board and profile shall be in linear shape with appropriate pvc edge banding. the table shall be clad with 18mm thick modesty panel which provide structural support for the table. it should be 18mm thick pre laminated particle board in linear shape with appropriate pvc edge banding connected with both end. there shall be buffers provided at the base to avoid scratches on the floor.a mobile pedestal shall be provided with an overall size 400mm x 450mm x 650mm. the pedestal shall be made up of pre laminated particle board of grade ii of is 12823. pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. the pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. the drawer shall be operated with ss handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. the pedestal shall be mounted over injection moulded nylon castor. 20 main chairproviding and supplying a high back chair with ergonomic design, comfortable & aesthetically appealing. the seat shall be made of 15mm thick hot pressed commercial plywood padded with high resilience polyurethane foam ( 30+25 ) mm thick having density ( 40 & 32 ) kg / m³ and the back shall be made of ( 15+6 ) mm thick double layered moulded plywood padded with high resilience polyurethane foam 30mm thick having density 32kg / m³. the same shall be upholstered with leatherite tapestry 1mm thick. the backrest shall be made by keeping the natural curvature of the spine which helps to provide lumbar support & full back support as well as head support. the chair shall be supplied with cushion arm with leatherite covering top completely joint with seat and back. for seating durability the chair shall have, synchro knee tilt 360 degree revolving mechanism having four position locking and tilt tension adjustment with anti shock feature which provides back strength for the chair. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 65mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standards. the pedestal should have five legged made of aluminium having pitch circle dia. 640 mm fitted with 5 nos. twin wheel castors. the castors of the chair shall be injection moulded in black 30% glass filled nylon, confirming to ansi / bifma x5.1 2011 standards tested to perform 98, 000 cycles with 250lbs load. the seat size shall be 515±10 mm ( d ) x 500±10 mm ( w ) and back size shall be 600±10 mm ( w ) x 790±10 mm ( h ) from seat. overall height shall be = 1210±10 mm, overall depth / width = 740±10 mm. 21 visitor chairproviding and supplying visitor chair with ergonomically designed. the seat and back shall be made up of 15mm and 12mm thick hot pressed commercial plywood padded with high resilience polyurethane foam 40mm thick having density 40kg / m³ in seat and 25mm thick having density 32kg / m³ in back. the same shall be upholstered with fabric tapestry 0.6mm thick and 235 gsm. the seat and back shall be arrested together with metal frame and the armrest shall be used wooden arm mounted on chrome plated pipe frame completely joint with seat and back. the frame structure shall be cantilever supported type made up of ms / crca chrome plated round pipe of dia 25.4mm with 2mm thick. there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 425±10 mm ( d ) x 430±10 mm ( w ) and back size shall be 430±10 mm ( w ) x 450±10 mm ( h ) from seat. overall height shall be = 885±10 mm, overall depth = 600±10 mm & overall width = 540±10 mm. 22 staff workstationworkstation 1 ( 1200x600x1200mm ) supplying & placing workstation table in completely knock down conditions with an overall size 1200mm widthx 660 / 1260mm depthx 1200mm height that is to be assembled at site. the worktop shall have the size 1200mm x 600mm made up 25mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the top profile shall be in linear shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be supported by 25mm thick gabel end shall made up of prelamintaed particle board with pvc edge banding on edges. the worktop shall be enclosed with wire manager cap for power connection provision. the workstation shall have panel based partition of 60mm thick with 1200 mm height and the framework shall be made of aluminium alloy extruded profiles. the partition shall have the assembly of flat top trim, top bar, mid bar, side pole, skirting, raceway and side pvc beading. the entire aluminium parts shall be pretreated and duly powder coated of 40 60μ dry film thick. all these frame work sections shall be fitted to each other by fasteners of 2mm thick which is properly zinc coated for corrosion resistant. raceway shall be provided of aluminium of size 118mm height below the work top as per requirement for inlaying of electrical management and carrying the wire horizontally. the exposed vertical and horizontal faces of the frames shall be snap fitted with side pvc beading and top trims respectively. the top tile at user front shall be with pin up fabric board and white boardand bottom tile shall be provide laminated board at front of the user .the beading shall have extruded profile and made of pvc. the trims shall be made of aluminium extrusions of size 60mm with 1.5mm thick. the partition shall have concealed wire management capabilities for responsive and safe operations of power, telecommunications and data ( lan ) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. slots / cutouts shall be given on raceways to fix all electrical and data points. zinc coated small top support brackets shall be fixed to the partition frame.top supporting sharing fixed pedestal shall be provided with an overall size 400mm x 450mm x 725mm. the pedestal shall be made up of pre laminated particle board of grade ii of is 12823. pedestal side, back, top, facia shall be 18mm thick and drawer base shall be 9mm thick. the pedestal shall have 2 nos. of drawer i.e. 2 filing drawer. the drawer shall be operated with ss handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. the pedestal shall be mounted on injection moulded nylon castor. workstation w1200 x d660 x h1200mm one seating ( with individual pedestal ) 23 workstation w2400 x d660 x h1200mm two seating ( with sharing pedestal ) 24 workstation w1200 x d1260 x h1200mm two seating ( each seating with individual pedestal ) 25 workstation w2400 x d1260 x h1200mm four seating ( two seating with sharing pedestal ) 26 workstation chair providing and supplying revolving chair. the seat shall be made of 15mm thick hot pressed plywood padded with high resilience moulded polyurethane foam having density 45kg / m³ and the back shall be made up of plastic inner padded with high resilience moulded polyurethane foam having density 32kg / m³ in back. the same shall be upholstered with fabric tapestry 1mm thick and 300gsm. the back and base of the chair shall be supplied with polypropylene cover. the armrest shall be used fixed polypropylene arm completely joint with seat. for seating durability the chair shall have push back revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standard. the pedestal should have five legged injection moulded in 30% glass filled black nylon having pitch circle dia. 650 mm fitted with 5 nos. twin wheel castor. the castor of the chair should be injection moulded in black nylon 30% glass filled, confirming to ansi / bifma x5.1 2011 standard tested to perform 98, 000 cycles with 250lbs load. the seat size shall be 430±10 mm ( d ) x 460±10 mm ( w ) and back size shall be 425±10 mm ( w ) x 425±10 mm ( h ) from seat. overall height shall be = 870±10 mm, base width / depth = 710±10 mm. 27 conference roomconference table ( 9900x3750x750mm ) supplying & placing conference table in completely knock down conditions with an overall size 9900mm x 3750mm x 750mm that is to be assembled at site. the construction of the main table shall be with minifix dowels, pins and ms brackets. the top shall be made up of 25mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the top profile shall be in c shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the table top shall be supported on particle board base gable end. the end wall of the table on the side shall be topped by gable end. it should be made up of 25mm thick pre laminated particle board and the profile shall be in linear shape with appropriate pvc edge banding. the table shall be clad with 18mm thick modesty panel which provide structural support for the table. the modesty panel shall be 18mm thick pre laminated particle board with appropriate pvc edge banding connected with both end. there shall be buffers provided at the base to avoid scratches on the floor. the table connections have to be made in such a way that no gap should be seen in between. table with wire carrier made of crca ms sheet duly powder coated fixed on modesty panel below work top for wire mangment and electrical and data plate mounting. table with wire riser made of crca ms sheet duly powder coated for rising of electrical and data wires from floor to wire carrier. ( color rose wood ) 28 chairman chair supplying and placing ergonomically designed, comfortable & aesthetically appealing high back chair. the seat shall be made of 15mm thick hot pressed curved plywood upholstered with high resilience polyurethane foam 50mm thick having density 40kg / m³ with khaki leatherite tapestry 0.8mm thick and 535 gsm and the back shall be supported by metal insert ms crca frame upholstered with high resilience polyurethane foam 12mm thick having density 23kg / m³ with khaki leatherite tapestry 0.8mm thick and 535 gsm with contoured lumbar support which helps to provide full back support and maintain the natural curvature of the spine. headrest shall be provided for comfort of head with leatherite tapestry. the armrest shall be used ms crca chrome plated with pu arm completely joint with seat and back. the chair shall have knee tilt 360 degree revolving mechanism with four position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height upto 100mm with bifma standard class 3 gaslift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standards. the pedestal shall be made up of ms crca chrome plated having pitch circle dia 640 mm fitted with 5 nos. 50mm twin wheel castors which shall be made of injection moulded black nylon 30% glass filled having self lubricating property for friction free movemen with bifma standards. the seat size shall be 485±10 mm ( w ) x520±10 mm ( d ) and back size shall be 740±10 mm ( h ) from seat, overall height = 1150±10 mm and overall depth / width= 740±10mm. ( color : mocha ) 29 main table chairproviding and supplying a medium back chair with ergonomic design, comfortable & aesthetically appealing. the seat shall be made of 15mm thick hot pressed commercial plywood and the back shall be supplied with metal pipe, inserted between backrest. the chair shall be padded with high resilience polyurethane foam 50mm thick having density 40kg / m³ in seat and 12mm thick having density 23kg / m³ in back. the seat and back shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 gsm and breathable mesh tapestry behind the backrest.. ms chrome plated pipe frame shall be provided on both side of seat and back with size 25mm x 10mm. the backrest shall be supplied by keeping the natural curvature of the spine which helps to provide full back support. the armrest shall be used black integral polyurethane arm mounted on crca chrome plated pipe having size 40mm x 10mm completely joint with seat and back with the assistance of allen key screw. a chrome plated round bend pipe of dia. 9mm shall be provided behind the backrest of the chair and welded with main frame. for seating durability the chair shall have knee tilt 360 degree revolving mechanism with four position locking and tilt tension adjustment which provides back strength for the chair. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standards. the pedestal shall have five legged crca chrome plated having pitch circle dia. 640mm fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black 30% glass filled, confirming to ansi / bifma standards x5.1 2011 tested to perform 98, 000 cycles with 250lbs load. the seat size shall be 490±10 mm ( w ) x 520±10 mm ( d ) and back size shall be 450±10 mm ( w ) x 535±10 mm ( h ) from seat & overall height = 980±10 mm, overall width / depth = 740±10 mm. ( color : mocha ) 30 wall side chairproviding and supplying a visitor chair with ergonomic design for user comfort & shall have aesthetically appealing. the seat shall be made of 15mm thick hot pressed commercial plywood and the back shall be supplied with metal pipe, inserted between backrest. the chair shall be padded with high resilience polyurethane foam 50mm thick having density 40kg / m³ in seat and 12mm thick having density 23kg / m³ in back. the seat and back shall be upholstered with leatherite tapestry 0.8±0.1mm thick, 535 gsm and breathable mesh tapestry behind the backrest. ms chrome plated pipe frame shall be provided on both side of seat and back with size 25mm x 10mm. the backrest shall be supplied by keeping the natural curvature of the spine which helps to provide back support. the armrest shall be used black integral polyurethane arm mounted on crca chrome plated pipe having size 40mm x 10mm completely joint with seat and back with the assistance of allen key screw. chrome plated round bend pipe of dia. 9mm shall be provided behind the backrest of the chair and welded with main frame. the frame structure shall be cantilever support type made of ms crca chrome plated round pipe of dia. 25.4mm with 2mm thick. there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 500±10 mm ( w ) x 510±10 mm ( d ) and back size shall be 450±10 mm ( w ) x 540±10 mm ( h ) from seat & overall height = 980±10 mm, overall width = 560±10 mm. ( color : mocha ) 31 video conference roomconference table ( 4800x2150x750mm ) supplying & placing conference table in completely knock down conditions with an overall size 4800mm x 2150mm x 750mm that is to be assembled at site. the construction of the main table shall be with minifix dowels, pins and ms brackets. the top shall be made up of 25mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the top profile shall be in c shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the table top shall be supported on particle board base gable end. the end wall of the table on the side shall be topped by gable end. it should be made up of 25mm thick pre laminated particle board and the profile shall be in linear shape with appropriate pvc edge banding. the table shall be clad with 18mm thick modesty panel which provide structural support for the table. the modesty panel shall be 18mm thick pre laminated particle board with appropriate pvc edge banding connected with both end. there shall be buffers provided at the base to avoid scratches on the floor. the table connections have to be made in such a way that no gap should be seen in between. table with wire carrier made of crca ms sheet duly powder coated fixed on modesty panel below work top for wire mangment and electrical and data plate mounting. table with wire riser made of crca ms sheet duly powder coated for rising of electrical and data wires from floor to wire carrier. ( color rose wood ) 32 main chair supplying and placing ergonomically designed, comfortable & aesthetically appealing high back chair. the seat shall be made of 15mm thick hot pressed curved plywood upholstered with high resilience polyurethane foam 50mm thick having density 40kg / m³ with khaki leatherite tapestry 0.8mm thick and 535 gsm and the back shall be supported by metal insert ms crca frame upholstered with high resilience polyurethane foam 12mm thick having density 23kg / m³ with khaki leatherite tapestry 0.8mm thick and 535 gsm with contoured lumbar support which helps to provide full back support and maintain the natural curvature of the spine. headrest shall be provided for comfort of head with leatherite tapestry. the armrest shall be used ms crca chrome plated with pu arm completely joint with seat and back. the chair shall have knee tilt 360 degree revolving mechanism with four position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height upto 100mm with bifma standard class 3 gaslift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standards. the pedestal shall be made up of ms crca chrome plated having pitch circle dia 640 mm fitted with 5 nos. 50mm twin wheel castors which shall be made of injection moulded black nylon 30% glass filled having self lubricating property for friction free movemen with bifma standards. the seat size shall be 485±10 mm ( w ) x520±10 mm ( d ) and back size shall be 740±10 mm ( h ) from seat, overall height = 1150±10 mm and overall depth / width= 740±10mm. ( color : mocha ) 33 medium back chairs providing and supplying a medium back chair with ergonomic design, comfortable & aesthetically appealing. the seat shall be made of 15mm thick hot pressed commercial plywood and the back shall be supplied with metal pipe, inserted between backrest. the chair shall be padded with high resilience polyurethane foam 50mm thick having density 40kg / m³ in seat and 12mm thick having density 23kg / m³ in back. the seat and back shall be upholstered with leatherite tapestry 0.8±0.1 mm thick and 535 gsm and breathable mesh tapestry behind the backrest.. ms chrome plated pipe frame shall be provided on both side of seat and back with size 25mm x 10mm. the backrest shall be supplied by keeping the natural curvature of the spine which helps to provide full back support. the armrest shall be used black integral polyurethane arm mounted on crca chrome plated pipe having size 40mm x 10mm completely joint with seat and back with the assistance of allen key screw. a chrome plated round bend pipe of dia. 9mm shall be provided behind the backrest of the chair and welded with main frame. for seating durability the chair shall have knee tilt 360 degree revolving mechanism with four position locking and tilt tension adjustment which provides back strength for the chair. the pneumatic seat height adjustment for healthy seating, user can adjust seat height up to 100mm with bifma standard class 3 gas lift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standards. the pedestal shall have five legged crca chrome plated having pitch circle dia. 640mm fitted with 5 nos. twin wheel castors. the castors of the chairs should be injection moulded in black 30% glass filled, confirming to ansi / bifma standards x5.1 2011 tested to perform 98, 000 cycles with 250lbs load. the seat size shall be 490±10 mm ( w ) x 520±10 mm ( d ) and back size shall be 450±10 mm ( w ) x 535±10 mm ( h ) from seat & overall height = 980±10 mm, overall width / depth = 740±10 mm. ( color : mocha ) 34 staff tabletable ( 1200x600x750mm ) supplying & placing executive table in completely knock down conditions with an overall size 1200mm x 600mm x 750mm that is to be assembled at site. the worktop shall be made up of 25mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the table top profile shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the top shall be supported on ms / crca rectangle pipe having cross section area 40mm x 20mm with 1.6mm thick. a pullout keyboard trey shall be provided of 18mm thick pre laminated particle board having size 550mm x 280mm. the trey shall be operated on keyboard channel. the table shall be clad with modesty panel which provide structural support for the table. it should be 1mm thick crca star perforated sheet connected with both end. the table understructure shall consist of c frame ms / crca leg having cross sectional area 60mm x 30mm. there shall be co polymer polypropylene shoe provided at the base to avoid scratches on the floor. a mobile pedestal shall be provided with an overall size 400mm x 450mm x 660mm. the pedestal shall be made up of pre laminated particle board of grade ii of is 12823. pedestal side, back, top, facia shall be 18mm thick and drawer base 9mm thick. the pedestal shall have 3 nos. of drawer i.e. 2 box drawer and 1 filing drawer. the drawer shall be operated with ss handle and easily close & open with the assistance of roller channel and ball bearing channel to enable smooth operation. the drawer shall have central locking mechanism in which all the drawer shall be synchronized locked with one single key. the pedestal shall be mounted on injection moulded nylon castor. 35 chair supplying and placing ergonomically designed, comfortable & aesthetically appealing medium back chair. the seat shall be made of 15mm thick hot pressed plywood with hr polyurethane foam 50mm thick having density 40kg / m³ upholstered with black leatherite tapestry with 0.8mm thick and 535 gsm and the back shall be supported by metal insert ms crca chrome plated with high resiliance polyurethane foam 12mm thick having density 23kg / m³ upholstered with black leatherite with 0.8mm thick and 535 gsm. the armrest shall be used cushion arm completely joint with seat and back. the chair shall have synchro tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height upto 100mm with bifma standard class 3 gaslift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standards. the pedestal shall be made up of ms crca chrome plated having pitch circle dia 700 mm fitted with 5 nos. 50mm twin wheel castors which shall be made of injection moulded black nylon 30% glass filled having self lubricating property for friction free movemen with bifma standards. the seat size shall be 490±10 mm ( w ) x490±10 mm ( d ) and back size shall be 555±10 mm ( h ) from seat & overall height = 1010±10 mm. 36 record roomcompactor providing and placing mechanically assisted drive mechanism mobile compactor. the structure shall be made out of 0.8 thick high yield strength crca sheet of grade d confirming to is:513. each unit have 5 loading levels formed by 4 nos. of adjustable shelves. body units are bolted to undercarriage. compactor height from ground should be 2125 mm ( 1980 body + 145 undercarriage ) . the body including shelves shall be given antirust surface treatment & powder coated with epoxy polyester powder. it involves an 7 step treatment, final finish consists of epoxy polyester powder coating of approved color & shade with a dry film thickness of minimum 40 microns. it shall have max. load bearing capacity of 60 kg uniformly distributed per shelf. shelves shall be mounted on support brackets & shelf level can be adjusted. the undercarriage shall be welded frame made of hr sheet minimum 2.5 mm thick suitably fabricated to take the loads based on configuration. a centralized locking arrangement shall be provided through locking stiffener mounted onto back of single last unit so that it gets locked on channels when all the units are brought together. this arrangement occupies a space of 100 mm. each drive type units have locking knob near the drive wheel for manual locking of individual units when a person is using those units. end stoppers are provided at the end of channels to prevent derailment. the nuts & bolts are galvanized / zn plated. movement of units shall be achieved mechanically through a drive wheel and ‘sprocket chain tensioner’ arrangement mounted rigidly onto body side.2 bay single static fixed , size : w1830 x d455 x h2150 37 2 bay double movable , size : w1830 x d910 x h2150 38 2 bay single last movable ( lockable ) , size : w1830 x d455 x h2150 39 canteencafe tables supplying & placing cafe table with an overall size 900mm x 900mm x 750mm. the top of the table shall be made up of 20mm thick granite rock. the top profile shall be in square shape and the edges shall be in round shape. the top shall be supported on 11mm thick ply board having size 750mm x 750mm and ss 202 grade pipe frame having cross section area 40mm x 20mm with 1.6mm thick in x shape. the table under structure shall be made up of ss grade 202 base pole leg having dia. 63.5mm. the base shall be in x shape with ss pipe frame having cross section area 40mm x 40mm. there shall be leveler shoe provided with metal insert at the base to avoid scratches on the floor. the manufacturer shall have quality and safety assurance like iso 9001:2015, iso 14001:2015 and iso 18001:2007, bifma membership and aiota certification. 40 cafe tables supplying & placing cafe table with an overall size dia. 750mm x h 1050mm. the top of the table shall be made up of 16.4mm thick granite rock. the top profile shall be in circular shape and the edges shall be in round. the top shall be supported on ply board having size dia. 750mm and ms chrome plated pipe frame having cross section area 30mm x 15mm. the table under structure shall consist of chrome plated pole leg having dia. 63.5mm. the base plate shall be made of ms powder coated sheet having dia. 465mm. 41 cafe tables supplying & placing cafe chair. the seat and back shall be made of moulded polypropylene shell of 5mm thick. the seat & back shall be bend in l type shape. the frame structure shall be supported by four legs made up of ms crca chrome plated round pipe of dia 20mm with 1.5mm thick. there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 390±10 mm ( d ) x440±10 mm ( w ) and back size shall be 440±10 mm ( w ) x385±10 mm ( ht ) from seat. overall height shall be = 815±10 mm, overall depth = 445±10 mm. 42 bed for police staff / night duty staffsingle bedproviding and placing in position single bed with an overall size 1985mm ( l ) x 910mm ( w ) x 690 / 400mm ( h ) without mattress. the construction of the bed shall be supplied in knock down with metal frame made out of ms / crca steel pipe having cross section area 50mm x 25mm with 1.2 thick. 3 nos. of crca round pipe shall be provide on head side with 15mm dia. the mattress panel shall be made of 1mm thick high yield strength crca sheet of grade d confirming to is:513 welded together with main frame and mounted on crca square pipe strips having cross section area 19.05mm x 19.05mm with 1 mm thick. the legs shall be made of m.s.e.r.w pipe having cross section area 50mm x 25mm with 1.2 mm thick. all metal part shall be powder coating finish with dft ( dry film thickness ) 35μ min. the ppcp shoes shall be insert into bottom of legs for avoid skretches on the floors with mattress ( size– 1800 x 850 x 4 inch , foam mattrees , 40 d foam and one side quilt ) and pillow ( 600 x 400 mm , material – cotton ) 43 low height modular partition for eto / aeto / officer cubiclesfull height partition supplying and placing panel based full height partition of 60mm thick with 106mm height ( upto ceiling height ) and the framework shall be made of aluminium alloy extruded profiles.the entire aluminium parts shall be pretreated and duly powder coated of 50 60μ dry film thick. all these frameshall be fixed to floor, wall and ceiling with neccessary fastenrs / brackets and hardwares. the top tileshall be pre laminated board / glass and bottom tile shall be provide laminated particle board. 44 staff workstation wall hanging over head storage.over head storage.supplying & placing overhead storage unit , the storage shall be made up of ply board of bwp grade is 710 with approved laminate and finish as per approved shade. it should be made up of 18mm thick like side, back, shutter, facia, skirting. the edges shall be sealed with thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the storage shall be supplied with 1 nos. of shelves. door shutters shall be provided for opening and closing the storage. the shutter shall be operated with concealed crank hinge and ss handle and proper locking arrangement. over head storage w1200 x d400 x h900mm 45 over head storage w810 x d400 x h900mm 46 over head storage w1040 x d400 x h900mm 47 over head storage w1015 x d400 x h900mm 48 waiting areasofa 3 seater supplying and placing a three seater bench that shall be constructed from metal frame. the seat and back shall be made of high quality cold rolled ms sheet of 1.2m thick, pressed and welded to form the shape. the seat and back shall be electrostatically coated with 40 60μ thick epoxy powder and then cured under heat to allow it to form a skin. the seat and back shall have round perforated sheet i.e. 4.5mm dia. hole. the seat and back shall be padded with 25mm thick high resilience polyurethane foam having density 40kg / m³ in seat and 32kg / m³ in back. it shall be upholstered with black leatherite tapestry 0.8±.1mm thick and 535 gsm. the seat shall be supported on 2.5mm thick crca powder coated hinge which is mounted over ms pipe having cross section area 50mm x 50mm with 2mm thick. the armrest shall be made up of ms powder coated with 1mm thick. the base or leg shall be made of 1mm thick crca powder coated sheet. there shall be leveler shoe provided with metal insert at the bottom to avoid scratches on the floor. the individual seat size shall be 415±10 mm ( d ) x 450±10 mm ( w ) , seat height = 450±10 mm, overall width = 1600±10 mm, overall depth = 600±10 mm & overall height = 790±10 mm. 49 sofa 2 seater supplying and placing a two seater bench that shall be constructed from metal frame. the seat and back shall be made of high quality cold rolled ms sheet of 1.2m thick, pressed and welded to form the shape. the seat and back shall be electrostatically coated with 40 60μ thick epoxy powder and then cured under heat to allow it to form a skin. the seat and back shall have round perforated sheet i.e. 4.5mm dia. hole. the seat and back shall be padded with 25mm thick high resilience polyurethane foam having density 40kg / m³ in seat and 32kg / m³ in back. it shall be upholstered with black leatherite tapestry 0.8±.1mm thick and 535 gsm. the seat shall be supported on 2.5mm thick crca powder coated hinge which is mounted over ms pipe having length 1100mm with cross section area 50mm x 50mm with 2mm thick. the armrest shall be made up of ms powder coated 40mm width with 1mm thick. the base or leg shall be 49mm width made of 1mm thick crca powder coated sheet. there shall be leveler shoe provided with metal insert at the bottom to avoid scratches on the floor. the individual seat size shall be 415±10 mm ( d ) x 450±10 mm ( w ) , seat height = 450±10 mm, overall width = 1100±10 mm, overall depth = 600±10 mm & overall height = 790±10 mm. 50 center table supplying & placing center table with an overall size 1200mm x 600mm x 450mm. the top of the table shall be made up of 12mm thick toughened glass with bevelled edges. the profile shall be in rectangle shape with round corner. the top shall be supported on ms chrome plated tubular frame with cross section area 40mm x 20mm with 1.6mm thick. the under structure shall consist of four legs made of ms chrome plated oval pipe having cross section area 52mm x 26mm with 1.6mm thick. there shall be co polymer polypropylene shoe provided at the bottom to avoid scratches on the floor. 51 corner table supplying & placing center table with an overall size 600mm x 600mm x 450mm. the top of the table shall be made up of 12mm thick toughened glass. the top profile shall be in square shape with round corner and the edges shall be in chamfer shape. the top shall be supported on ms chrome plated oval frame with cross section area 40mm x 20mm with 1.6mm thick. the under structure shall consist of four legs made of ms chrome plated oval pipe having cross section area 52mm x 26mm with 1.6mm thick. there shall be co polymer polypropylene shoe provided at the bottom to avoid scratches on the floor. 52 receptiontable ( 3000x820x1000mm ) .supplying & placing reception table in completely knock down conditions with an overall size 3000mm x 820mm x 1000mm that is to be assembled at site. the top shall have the size 2900mm x 695mm made up of 49mm thick pre laminated particle board of grade ii of is 12823 with approved laminate and finish as per approved shade. the upper top shall have the size 1800mm x 300mm with 49mm thick. the top profile shall be in rectangle shape with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. the side edges shall be covered with die casted aluminium profile. the table top and upper top shall be supported on particle board base strip. the table shall have a front panel having size 1390mm x 750mm with 49mm thick pre laminated particle board. a wire manager cap shall be provided on the top of the table for power connection. the end wall of the table on the side shall be topped by gable end. it shall be made up of 49mm thick pre laminated particle board and profile shall be in linear shape with one clipped corner and covered by aluminium profile. there shall be buffers provided to avoid the scratches on the floor. the table shall be clad with 49mm thick modesty panel which provide structural support for the table. it should be 49mm thick pre laminated particle board in linear shape with appropriate pvc edge banding and covered by aluminum profile connected with both end. two side hanging drawer of size 400x450x450mm fixed below table top shall be made of 18mm thick plpb with one drawer and one filling drawer. 53 chair supplying and placing ergonomically designed, comfortable & aesthetically appealing medium back chair. the seat shall be made of 15mm thick hot pressed plywood with hr polyurethane foam 50mm thick having density 40kg / m³ upholstered with black leatherite tapestry with 0.8mm thick and 535 gsm and the back shall be supported by metal insert ms crca chrome plated with high resiliance polyurethane foam 12mm thick having density 23kg / m³ upholstered with black leatherite with 0.8mm thick and 535 gsm. the armrest shall be used cushion arm completely joint with seat and back. the chair shall have synchro tilt 360 degree revolving mechanism with upright position locking and tilt tension adjustment. the pneumatic seat height adjustment for healthy seating, user can adjust seat height upto 100mm with bifma standard class 3 gaslift to suit them using the lever under the seat. the gas lift mechanism should be tested as per ansi / bifma x5.1 2011 standards. the pedestal shall be made up of ms crca chrome plated having pitch circle dia 700 mm fitted with 5 nos. 50mm twin wheel castors which shall be made of injection moulded black nylon 30% glass filled having self lubricating property for friction free movemen with bifma standards. the seat size shall be 490±10 mm ( w ) x490±10 mm ( d ) and back size shall be 555±10 mm ( h ) from seat & overall height = 1010±10 mm. ( color : black / brown ) 54 sofa supplying and placing three seater sofa that shall be constructed from natural hard wood and commercial plywood having inner frame. the thickness of the wood should allow for the heavy tension webbing. the sofa shall have spring attached and also be padded separately. the frame shall be padded with high resilience polyurethane foam having density 40kg / m³ in seat and 32kg / m³ in back. there shall be cushion arm provided padded with high resilience polyurethane foam having density 40kg / m³. the structure shall be upholstered with leatherite tapestry 1±0.2 mm thick and 571 gsm. the sofa shall be supported on ms powder coated pipe frame having size 40mm x 20mm. the under structure shall consist of ms powder coated round leg with upper dia. 38mm and lower dia. 30mm. there shall be shoe provided at the bottom to avoid scratches on the floor. the seat size shall be 570±10 mm ( d ) x 1660±10 mm ( w ) , seat height = 425±10 mm, overall width = 2020±10 mm, overall depth = 750±10 mm & overall height = 680±10 mm. 55 center table supplying & placing center table with an overall size 1200mm x 600mm x 450mm. the top of the table shall be made up of 12mm thick toughened glass with bevelled edges. the profile shall be in rectangle shape with round corner. the top shall be supported on ms chrome plated tubular frame with cross section area 40mm x 20mm with 1.6mm thick. the under structure shall consist of four legs made of ms chrome plated oval pipe having cross section area 52mm x 26mm with 1.6mm thick. there shall be co polymer polypropylene shoe provided at the bottom to avoid scratches on the floor. 56 corner table supplying & placing center table with an overall size 600mm x 600mm x 450mm. the top of the table shall be made up of 12mm thick toughened glass. the top profile shall be in square shape with round corner and the edges shall be in chamfer shape. the top shall be supported on ms chrome plated oval frame with cross section area 40mm x 20mm with 1.6mm thick. the under structure shall consist of four legs made of ms chrome plated oval pipe having cross section area 52mm x 26mm with 1.6mm thick. there shall be co polymer polypropylene shoe provided at the bottom to avoid scratches on the floor. 57 steel almirah ( room for officer , hall for officer & pa staff of jetc / detc ) steel almirah providing, supplying and placing steel almirah in perfectly upright and straight position. the overall size of the almirah shall be 915mm ( w ) x 455mm ( d ) x 1850mm ( h ) . the almirah shall be supplied with 2 nos. of glass sliding doors and 2 nos. swing door. the storage shall have 4 nos. of adjustable shelves. the door shall be operated with ppealing snap fit abs plastic handle and concealed crank hinge as well as sliding channel. the glass shall be used 4mm thick. the shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. uniformly distributed load capacity of each shelf shall be 40 kg maximum. each rack shall be provided with stiffener at bottom for strength. the entire body panel, shelf shall be made of high yield strength 0.8mm thick and door 1mm thick crca sheet of grade ‘d’ confirming to is: 513. to protect the ball from kicks, abrasion and serve as a decorative moulding skirting shall be provided at the bottom of the almirah. the complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to the thickness 40 50μ thick.steel almirah w750 x d455 x h1850mm 58 steel almirah w915 x d455 x h1850mm 59 steel almirah for hall for staff & central computing labsteel almirah providing, supplying and placing steel almirah in perfectly upright and straight position.it should be supplied with 2 / 4 nos. of adjustable shelves i.e. 5 loading compartments. door shall be made of 1mm thick and all other components shall be made of 0.8mm thick high yield strength crca sheet of grade ‘d’ confirming to is: 513. stiffeners shall be provided in shelf & door. the steel hinged door shall be provided with locking mechanism which is assembled with bolt arrangement. the shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. uniformly distributed load capacity per each shelf shall be 40kg maximum. the complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to be thickness 40 60μ.steel almirah w 750 x d450 x h1200 mm ( 2 shelf ) 60 steel almirah w 900 x d450 x h1200 mm ( 2 shelf ) 61 steel almirah w 1200 x d450 x h1200 mm ( 2 shelf ) 62 steel almirah w900 x d450 x h1830mm ( 4 shelf ) 63 locker overall size of personal locker unit with add on units shall be of dimensions 380mm ( w ) x 450mm ( d ) x 1800mm ( h ) having 4 locker unit. stackability shall have add on units that can be stacked width wise to form bank of lockers having common side panel. locking shall have cam lock with lock lever plus option. material shall be crca 0.8 mm thickness. shelf shall be uniformly distributed load capacity per each shelf level is 35 kg maximum. finish shall be epoxy polyester powder coated to the thickness of 50 microns. handle / label holder shall be aesthetically appealing snap fit abs plastic handle. ventilation shall be attractive punched pattern for ventilation. 64 ss 3 seater sofa supplying & placing three seater bench. the seat and back shall be made up of ss 304 grade perforated sheet of 1 mm thick, pressed and welded to form the shape. the armrest shall be made up of ss304 grade ovaltube with 1.5mm thick. the base structure shall be supported byss 304 grade legs and beam. there shall be ppcp shoe provided at the base to avoid scratches on the floor. the seat size shall be 440±10 mm ( d ) x 480 ±10 mm ( w ) x 410±10 mm ( h ) from ground. overall height shall be = 790±10 mm, overall depth = 710 ±10 mm & overall width = 1770±10 mm without cuhioned seat & back 65 ss dustbin ss perforated open dustbin .capacity : 11 lt , size : 10 x 14. 66 steel almirahs providing, supplying and placing steel almirah in perfectly upright and straight position. the overall size of the almirah shall be 915mm ( w ) x 485mm ( d ) x 1980mm ( h ) including legs. it should be supplied with 4 nos. of adjustable shelves i.e. 5 loading compartments. door shall be made of 1mm thick and all other components shall be made of 0.8mm thick high yield strength crca sheet of grade ‘d’ confirming to is: 513. stiffeners shall be provided in shelf & door. the steel hinged door shall be provided with locking mechanism which is assembled with bolt arrangement. the shelves shall have folded constructions which have intrinsic rigidity and high load carrying capacity. uniformly distributed load capacity per each shelf shall be 40kg maximum. the complete steel structure shall be constructed by welding and provide finishing with epoxy polyester powder coated to be thickness 50 60μ....

Public Works Department - Haryana

31079465 providing and fixing overhead cantilever and providing and fixing overhead cantilever and gantry boards for compliance of road safety on saharanpur kurukshetra pehowa cheeka road sh06 in district kurukshetra...