Haryana Police Housing Corporation Limited - Haryana

36912156 renovation / upgradation of babu anant ram janta college at kaul, distt. kaithal 1 [10.100.2]cement concrete 1:8:16 flooring 2. cement concrete 1:8:16 with stone aggregate 40 mm size in foundation and plinth. 2 [10.58]providing and fixing 1st quality ceramic glazed wall tiles conforming to is : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by engineer in charge in skirting, risers of steps and dados over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. 3 [10.63.2]providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to is: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqmincluding grouting the joints with white cement and matching pigments etc., complete. 2. size of tile 600x600 mm 4 [10.67.2]providing and laying vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to i.s. 15622, of approved make, in all colours and shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement and matching pigments etc. complete. 2. size of tile 600x600 mm 5 [10.70.2]extra for grouting the joints of floor tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of engineer in charge. 2. size of tile 600x600 mm 6 [11.5.4]12 mm cement plaster of mix : 4. 1:6 (1 cement: 6 fine sand) 7 [11.60]providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. 8 [11.76]preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to required finish complete. 9 [11.77]applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping etc. 10 [11.78]painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. 11 [12.103.2]providing and fixing aluminium hanging floor door stopper, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. 2. twin rubber stopper 12 [12.157.1.2]providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / panelling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. (glazing, panelling and dash fastenersto be paid for separately) : 1.2. for fixed portionpowder coated aluminium (minimum thickness of powder coating 50 micron) 13 [12.157.2.2]providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate z sections and other sections of approved make conforming to is: 733 and is: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required epdm rubber/ neoprene gasket etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / panelling, c.p. brass / stainless steel screws, all complete as per architectural drawings and the directions of engineer in charge. (glazing, panelling and dash fastenersto be paid for separately) : 2.2. for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of epdm rubber / neoprene gasket required (fittings shall be paid for separately) powder coated aluminium (minimum thickness of powder coating 50 micron) 14 [12.158.2]providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to is: 12823 grade l type ll, in panelling fixed in aluminium doors, windows shutters and partition frames with c.p. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer in charge. 2. pre laminated particle board with decorative lamination on both sides 15 [12.159.2]providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with epdm rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer in charge . (cost of aluminium snap beading shall be paid in basic item): 2. with float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) 16 [12.171]providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top and bottom pivot and double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of engineer in charge (door handle, lock and stopper etc.to be paid separately). 17 [12.37.1]providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) non decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 1. 35 mm thick including isi marked stainless steel butt hinges with necessary screws 18 [12.37.3]providing and fixing isi marked flush door shutters conforming to is : 2202 (part i) non decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 3. 25 mm thick (for cupboard) including isi marked nickel plated bright finished m.s. piano hinges with necessary screws 19 [12.50.1]providing and fixing m.s. grills of required pattern in frames of windows etc. with m.s. flats, square or round bars etc. including priming coat with approved steel primer all complete. 1. fixed to steel windows by welding 20 [12.60.1]providing and fixing bright finished brass hasp and staple (safety type) with necessary screws etc. complete : 1. 150 mm 21 [12.98.2]providing and fixing aluminium sliding door bolts, isi marked anodised (anodic coating not less than grade ac 10 as per is : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 2. 250x16 mm 22 [12.99.3]providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 3. 200x10 mm 23 [12.99.4]providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 4. 150x10 mm 24 [12.99.5]providing and fixing aluminium tower bolts, isi marked, anodised (anodic coating not less than grade ac 10 as per is : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 5. 100x10 mm 25 [13.3.1.2]providing and fixing pressed steel door frames conforming to is: 4351, manufactured from commercial mild steel sheet of 2.0 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 2.00 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including m.s. pressed butt hinges 2.5 mm thick with mortar guards, lock strike plate and shock absorbers as specified and applying a coat of approved steel primer after pre treatment of the surface as directed by engineer in charge: 1.2. profile b fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately) 26 [13.3.2.2]providing and fixing pressed steel door frames conforming to is: 4351, manufactured from commercial mild steel sheet of 2.0 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 2.00 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including m.s. pressed butt hinges 2.5 mm thick with mortar guards, lock strike plate and shock absorbers as specified and applying a coat of approved steel primer after pre treatment of the surface as directed by engineer in charge: 2.2. profile c fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately) 27 [13.9.2]providing and fixing fly proof wire gauze to windows, clerestory windows and doors with m.s. flat 15x3 mm and nuts and bolts complete. 2. stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides 28 [20.26.1]cutting holes up to 23 cm through stone masonry or brick work in cement walls for pipes and making good including repointing, replastering and finishing according to existing finish where required. 1. 11.43 cm thick wall 29 [20.26.2]cutting holes up to 23 cm through stone masonry or brick work in cement walls for pipes and making good including repointing, replastering and finishing according to existing finish where required. 2. 22.86 cm thick wall 30 [20.55.4]providing and screwing in brass/gun metal ferrules drilling and tapping a.c. /pvc pipe lines of all diameters and connections including cost of m.s. clamp (heavy) with welded socket/saddle piece including carriage, loading, unloading etc. complete in all respects to the satisfaction of engineer in charge. (excavation will be paid separately). 4. 10mm i/d ferrule on 80mm i/d pipes 31 [21.84.2]constructing brick masonry inspection chamber sizes as given below up to 0.60 metre average depth in cement mortar 1:5 lime concrete with 40 per cent lime mortar 2:3 in foundation cement concrete 1:2:4 benching 12mm thick cement plaster 1:2 with a floating coat of 1 mm thick of neat cement r.c.c. 1:2:4 slab 100 mm thick/cement concrete topping, 50mm thick with 455mmx455mm / 455mm x610mm inside light duty c.i. inspection chamber cover and frame weight as per i.s.i. specification painted with 3 coats of black bitumastic superior paint complete as per standard design. 2. size 450 mm x 600 mm inside (with 455 mm x 610 mm cover and frame single seal pattern i weighing 38 kg with c.c. topping) 32 [21.84.3]constructing brick masonry inspection chamber sizes as given below up to 0.60 metre average depth in cement mortar 1:5 lime concrete with 40 per cent lime mortar 2:3 in foundation cement concrete 1:2:4 benching 12mm thick cement plaster 1:2 with a floating coat of 1 mm thick of neat cement r.c.c. 1:2:4 slab 100 mm thick/cement concrete topping, 50mm thick with 455mmx455mm / 455mm x610mm inside light duty c.i. inspection chamber cover and frame weight as per i.s.i. specification painted with 3 coats of black bitumastic superior paint complete as per standard design. 3. size 600 mm x900 mm inside (with 455 mm x 455 mm cover and frame light duty single seal weighing 20 kg with r.c.c. slab) 33 [22.10.2.2]providing and fixing stainless steel a isi 304 (18/8) kitchen sink as per is:13983 with c.i. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : 2.2. kitchen sink without drain board610x460 mm bowl depth 200 mm 34 [22.101.1.1]providing and fixing unplasticised pvc connection pipe with brass unions : 1.1. 30 cm length 15 mm nominal bore 35 [22.101.1.2]providing and fixing unplasticised pvc connection pipe with brass unions : 1.2. 30 cm length 20 mm nominal bore 36 [22.102.2]providing and fixing c.p. brass shower rose with 15 or 20 mm inlet : 2. 150 mm diameter 37 [22.104.1]providing and fixing c.p. brass bib cock of approved quality conforming to is:8931 : 1. 15 mm nominal bore 38 [22.105.1]providing and fixing c.p. brass long nose bib cock of approved quality conforming to is standards and weighing not less than 810 gms. 1. 15 mm nominal bore 39 [22.107.1]providing and fixing c.p. brass stop cock (concealed) of standard design and of approved make conforming to is:8931. 1. 15 mm nominal bore 40 [22.108.1]providing and fixing c.p. brass angle valve for basin mixer and geyser points of approved quality conforming to is:8931 1. 15mm nominal bore 41 [22.109]providing and fixing c.p. brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of engineer in charge. 42 [22.14.1.1]providing and fixing p.v.c. waste pipe for sink or wash basin including p.v.c. waste fittings complete. 1.1. semi rigid pipe 32 mm dia 43 [22.14.1.2]providing and fixing p.v.c. waste pipe for sink or wash basin including p.v.c. waste fittings complete. 1.2. semi rigid pipe 40 mm dia 44 [22.181]providing and placing on terrace (at all floor levels) polyethylene water storage tank, is : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. 45 [22.209]providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with c.p. brass screws and washers complete. 46 [22.22.1]providing and fixing water closet squatting pan (indian type w.c. pan ) with 100 mm sand cast iron p or s trap, 10 litre low level white p.v.c. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to is : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: 1. white vitreous chinaware orissa pattern w.c. pan of size 580x440 mm with integral type foot rests 47 [22.222.2.2]providing and fixing in position singel socket swr upvc soil waste or antisyphonage pipes as per is 13592 of e.d.c manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. 2.2. single socket type b 110mm o/d swr upvc pipe lines laid complete 48 [22.222.2.3]providing and fixing in position singel socket swr upvc soil waste or antisyphonage pipes as per is 13592 of e.d.c manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. 2.3. single socket type b 90mm o/d swr upvc pipe lines laid complete 49 [22.26.3]providing and fixing white vitreous chinaware flat back half stall urinal of size 580x380x350 mm with white pvc flushing cistern, with fittings, standard size c.p. brass flush pipe, spreaders with unions and clamps (all in c.p. brass) with waste fitting as per is : 2556, c.i. trap with outlet grating and other couplings in c.p. brass, including painting of fittings and cutting and making good the walls and floors wherever required : 3. range of two half stall urinals with 5 litre p.v.c. automatic flushing cistern 50 [22.34]providing and fixing floor mounted, white vitreous chinaware single piece, double traps syphonic water closet of approved brand/make, shape, size and pattern including integrated white vitreous chinaware cistern of capacity 10 litres with dual flushing system, including all fittings and fixtures with seat cover, cistern fittings, nuts, bolts and gasket etc including making connection with the existing p/s trap, complete in all respect as per directions of engineer in charge. 51 [22.38]providing and fixing 8 mm dia c.p. / s.s. jet with flexible tube up to 1 metre long with s.s. triangular plate to european type w.c. of quality and make as approved by engineer in charge. 52 [22.4]providing and fixing wash basin with c.i. brackets, 15 mm ptmt pillar cock, 32 mm ptmt waste coupling ofstandard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required. white vitreous chinaware flat back wash basin size 550x400 mm with single 15 mm ptmt pillar cock. 53 [22.5]providing and fixing white vitreous chinaware pedestal for wash basin completely recessed at the back for the reception of pipes and fittings. 54 [22.85.3]providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot and cold water supply, including all cpvc plain and brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes and fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. 3. 25 mm nominal outer dia pipes 55 [22.85.4]providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot and cold water supply, including all cpvc plain and brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes and fittings with one step cpvc solvent cement and testing of joints complete as per direction of engineer in charge. 4. 32 mm nominal outer dia pipes 56 [22.86.2]providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot and cold water supply, including all cpvc plain and brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes and fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. 2. 20 mm nominal outer dia pipes 57 [22.86.3]providing and fixing chlorinated polyvinyl chloride (cpvc) pipes, having thermal stability for hot and cold water supply, including all cpvc plain and brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. this includes jointing of pipes and fittings with one step cpvc solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of engineer in charge. 3. 25 mm nominal outer dia pipes 58 [30.25.1]distempering with 1st quality acrylic distemper (ready mix) having voc content less than 50 grams/ litreof approved brand and manufacture to give an even shade : 1. old work (one or more coats) 59 [30.37.1]finishing walls with acrylic smooth exterior paint of required shade : 1. old work (two or more coat applied @ 1.67 litre/ 10 sqm) on existing cement paint surface 60 [32.47.1]providing and fixing mineral fibre false ceiling tiles at all heights of size 595x595mm of approved texture, design and pattern. the tiles should have humidity resistance (rh) of 99%, light reflectance = 85%, thermal conductivity k = 0.052 0.057 w/m k, fire performance as per (bs 476 pt 6 and7)in true horizontal level suspended on interlocking t grid of hot dipped all round galvanized iron section of 0.33 mmthick (galvanized @120 gsm) comprising of main t runners of 15x32 mm of length 3000 mm, cross t of size 15x32mm of length 1200 mm and secondary intermediate cross t of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter m 6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and l shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main ‘t’. the system should rest on periphery walls /partitions with the help of gi perimeter wall angle of size24x24x3000 mm made of 0.40 mm thicksheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre and 40 mm long dry wall s.s. screws. the exposed bottom portion of all t sections used in false ceiling support system shall be pre painted with polyester baked paint, for all heights. the work shall be carried out as per specifications, drawings and as per directions of the engineer in charge. 1. with 16 mm thick bevelled tegular mineral fibre false ceiling tile (nrc 0.55 to 0.6 61 [5.29.1]dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : 1. of area 3 sq. metres and below 62 [5.29.2]dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : 2. of area beyond 3 sq. metres 63 [5.7.4]demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of engineer in charge. 4. in cement mortar 64 [7.22.2]brick work with common burnt clay non modular bricks of class designation 10.5 in superstructure above plinth level up to floor iv level in all shapes and sizes in : 2. cement mortar 1:6 (1 cement : 6 coarse sand) 65 [7.28.2]half brick masonry with common burnt clay non modular bricks of class designation 10.5 in superstructure above plinth level up to floor iv level. 2. cement mortar 1:4 (1 cement :4 coarse sand) 66 [8.26.2.2]providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 2.2. granite of any colour and shadearea of slab over 0.50 sqm 67 [8.27.2]providing edge moulding to 18 mm thick marble stone counters, vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by engineer in charge. 2. granite work 68 ns 69 providing and fixing cp jali with frame complete in all respect 70 providing & fixing swr pvc vent cowl with jali 90mm dia 71 providing & fixing swr pvc coupler/ socket 90mm dia 72 providing & fixing swr pvc bend with door 90mm dia 73 providing & fixing swr pvc nanhi trap with jali(110x110mm) 74 providing & fixing swr pvc vent cowl with jali 110mm dia 75 providing & fixing swr pvc coupler/ socket 110mm dia 76 providing & fixing swr pvc bend with door 110mm dia 77 providing & fixing swr pvc p trap(ds) 110 x 110mm 78 providing and fixing swr pvc single t with door90mm dia 79 providing and fixing swr pvc single t with door 110mm dia 80 providing and fixing swr pvc single t 110mm dia 81 providing and fixing ms rod 8mm fully threadedwith nut bolts and washer inserted in aluminium sections, window and door shutters complete in all respect 82 providing and fixing cpvc ball valve/ gate valve (union type) with of approved quality complete in all respect25mm dia 83 providing and fixing cpvc ball valve/ gate valve (union type) with of approved quality complete in all respect40mm dia 84 providing and fixing swr pvc single t 90mm dia ...

Military Engineer Services - Haryana

34996897 special repair of equipment shed no g 149, g 150, g 151 g 152 of 140 ad regt and provision of drainage from offrs mess bldg no p 144 to main drain in b area, allenby line of age br i under ge ( south ) ambala cantt material and labour for brick work with sub class ‘b’ bricks, straight or curved on plain exceeding 6 metre mean radius in cement mortar ( 1:6 ) including demolition of brick work built in cement mortar including demolition of old brick / stone masonry built in cement mortar of any description including all quoins, archs, pillars etc complete all as specified and directed. 2 material and labour for brick work ( except bricks ) straight or curved on plan exceeding 6 metre mean radius built in cm 1:6 ( old size brick ) including demolition of old brick masonry built in cement mortar of any description including all quoins, archs, pillars etc complete all as specified and directed. 3 taking down cement plaster on brick or stone walls, etc., including raking out joints, hacking for key, scrubbing down with water, etc. complete all as specified and directed. 4 material and labour for rendering 15 mm thick on any faces of old brick work in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed. 5 material and labour for rendering 15 mm thick on fair faces of new brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement complete all as specified and directed. 6 material andlabour for preparation of exposed brick wall surface by cleaning the surface wire brush to remove all dirt / loose materials from the bricks and from the joints between the bricks. prepared surface should be then washed with diluted hcl acid ( dilution ratio of 1:50 ) for three times in a day for two days. after acid wash surface should be allowed to be air dried for one day. note : further treatment over the surface so achieved will be carried out only after approved of the same by ge. 7 material and labour for carrying out efflorescence treatment to unplastered wall surface comprising of the following specifications and sequence with and including 15 mm thick rendering in cm 1:4 finished even and smooth without using extra cement : ( a ) prime the prepared surface with one of the following product mixed with cement in 1:1 ratio as bonding agent : ( i ) pidicrete urp of m / s pidilite. ( ii ) sika latex of m / s sika. ( iii ) nitobond sbr latex of m / s fosroc. ( b ) immediately after priming the surface pmm ( polymer modified mortar ) to be applied “by hand” while the prime is tacky. pmm should be prepared by mixing one of the following compounds in cement mortar 1:3 as per manufacturer’s instructions: ( i ) pidicrete urp of m / s pidilite. ( ii ) sika latex of m / s sika. ( iii ) nitobond sbr latex of m / s fosroc. ( c ) pmm surface should be allowed to dry for one day. after that it should painted with two coats of one of the following compound mixed with cement only in ratio of 1 ( selected compound ) : 1:5 ( cement ) : ( i ) pidicrete urp of m / s pidilite. ( ii ) sika latex of m / s sika. ( iii ) nitobond sbr latex of m / s fosroc. ( d ) now apply two coats of one of the following compound over the surface. these compounds are to be used as per manufacturer’s instructions: ( i ) pidifin 2k of m / s pidilite. ( ii ) brush coat of m / s sika. ( iii ) brush bond of m / s fosroc.note : both coats should be perpendicular to each other and gap between two coats shall be minimum 6 hours. ( e ) sprinkle loose coarse sand after second coat while surface is tacky.note: ( i ) the item will be executed by authorized applicator only of the selected / approved company. contractor shall submit details of authorised applicator for approval of ge before commencement of work in respect of above item. ( ii ) every stage of work will be approved by ge, then only next layer will be executed by contractor. 8 material and labour for rough cast plaster with and including 15mm thick rendering in cm 1:3 on brick wall or concrete surface as specified in clause 14.22 of ssr part i complete all as specified and directed.note: ( i ) after applying the under coat of cement and sand mortar 1:3 not less than 10 mm thick andwhile it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravelaggregate ( which is generally of size between 6 to 12 mm depending on the texture required ) mixed with coarse sand and cement in the ratio of 1: 1: 1 shall be applied and finished even. ( ii ) the mix of cement and sand shall be made slightly wetter than normal for rendering to ensurethat larger aggregates are thoroughly covered 9 material and labour for preparation of new plastered surfaces of walls and applying three coats of white wash on wall, complete all as specified and directed. 10 material and labour for preparation of new plastered surfaces of wall and applying two coats of cement base paint over a coat of alkali resistant primeron walls complete all as specified and directed. 11 material andlabour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper with hand roller, over a coat of alkaline resistant primer over a coat of wall care puttynot less than 1mm thick as per manufacturers instruction complete all as specified and directed. 12 material andlabour for preparation of old plastered surfaces of walls and applying two coats of white wash complete all as specified and directed. 13 material and labour preparation of old plastered surfaces of walls and applying one coat of cement base paint complete all as specified and directed. 14 supply andfixing of pre painted galvalume aluminium zinc coating gi based corrugatedsteel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa tensile strength as in roof covering / cladding to wall, fixed with self tapping screws or j type hooks including rubber washer etc complete including dismantling asbestos cement corrugated or semi corrugated sheets etc; complete all as specified and as directed. 15 supply andfixing of pre painted galvalume aluminium zinc coating gi based galvanised plain mild steel sheeting 0.50 mm thick of any colour, having 550 mpa tensile strength as in roof covering / ridges and fixed with self tapping screws or j type hooks including rubber washer etc complete including dismantling asbestos cement corrugated or semi corrugated sheets etc; complete all as specified and as directed. 16 dismantling timber scantling 40 sq. cm and over in section, in any position of unframed / framed work complete all as specified and directed. 17 material and labour for preparation of old painted steel surfaces of any description not otherwise described, over 10 cm in width or girth and applying one coat of synthetic enamel paint with approved shade complete all as specified and directed. 18 material and labour for taking down of rolled mild steel roof trusses ( framed ) of clear span above 08.00 metre and upto 12.00 metre any type, taking in safe costudy and refixing the same with and including using new nut bolts, welding & distance pieces, cleats etc., after completion of truss connected repair work etc complete all as specified anddirected. note: any damage to the existing truss during dismantling or refixing etc, shall be made good by the contractor with the same specifications as per existing work, without any extra cost to the govt. 19 dismatling of mild steel beam, purlin of existing truss andrefixing the same ( using nut bolt, welding ) rolled mild steel plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases, splices, angle brackets, cleats & other connections gde fe410 0 or fe 310 o complete all as specified and as directed. 20 supply and fixing of rolled mild steel sections as in main & cross beams, hip & jack rafters; purlins where connected to common rafters & running rails & guides for sliding doors; fixed with angle cleats or other connecting plates gde fe410 0 or fe 310 o complete all as specified and as directed. 21 supply andfixing of rolled mild steel work in roof trusses ( framed ) , trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing ( beam, tee, angle, channel or flat sections ) including distance pieces, cleats etc., quality confirming tofe 410 w ( gde e 250 ) quality a, complete, all as specified and as directed. 22 supply andfixing of mild steel plates ( plain or chequered ) channels, square cut or notched ( ordinary and counter sunk ) forming holes, with riveted, bolted or welded attachment conforming to grade fe 410 ( gde 250 ) , complete all as specified and directed. 23 material and labour for steel screw bolts, machine made, dia of neck 11 to 15mm with hexagonal or square head one end and screwed the other or screwed both ends, each screwed end to be fitted with washer and one hexagonal or square nut exceeding 22.5 cm and not exceeding 30cm long, complete all as specified and directed. 24 material and labour for two coats of synthetic enamel paint on steel surfaces over a coat of red oxide primerincludingpreparation of new steel surfaces of any description not otherwise described over 10 cm width or girth, complete all as specified and as directed. 25 material and labour for hardcore of gauge not exceeding 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed. 26 material and labour for 150mm thick pcc 1:2:4 type b2 using 40mm graded mechanically crushed stone aggregate as in hardstanding / paths, finishing the concrete surface even and smoothwithout using extra cement including formingjoints and fillingwith mixture of bitumen and sand in ratio ( 1:1 ) by weight including necessary formwork etc and including demolition of existing old cement concrete in ground floors and pavings n.exc 15cm thickness ( below or above ) ground level complete all as specified and directed. 27 material and labour for 50mm thick pcc ( 1:3:6 ) type c 1 using 20mm graded mechanically crushedstone aggregate as in plinth protection finished even and smooth without using extra cement with & including 10mm wide, 30mm deep joints at the rate of 3.00 mtr centre to centre and at every turning & filling the joints with bitumen & sand mixture including demolition of cement concrete in ground floor and pavings not exceeding 15 cm below or above ground level etc complete all as specified and directed. 28 surface excavation not exceeding 30 cm deep, averaging 15 cm deep and getting out in soft / loose soil, complete all as specified and directed. 29 material and labour for 100mm thick pcc ( 1:4:8 ) type d 2 using 40mm graded mechanically crushed stone as in sub base of floor / hard standing finished, complete all as specified and directed. 30 material and labour for providing and laying 80mm thick factory made chamfered edge cement concrete paver block of m 40 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size / shape, made by table vibratory method using pu mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed 31 material and labour for providing and laying of precast pcc solid concrete block, grade c confirming to is 2185 ( part i ) 2005 of 45 cm high, 10 cm thick and of suitable width including chamfers, weatherings, throating etc as in kerb continuous edging jointed in cement mortar 1:4 and struck flush pointing as the work proceeds and finishing with neat cement flush joint, complete all as specified and directed. 32 material andlabour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.11sqm but not exceeding 0.18 sqm, 7 to 8 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg / square metre and pointed in white or coloured cement to match the surface over and including15mm thick screed bed or layer in cement mortar ( 1:4 ) including dismantling of existing tiles etc including cement mortar bedding ( but not backing ) andrubbish off the premises complete all as specified and directed. 33 material and labour forpremium quality coloured glazed ceramic tiles ( 300x 450x 7mmthick ) in vertical surfacesand jointed in neat cement slurry @ 3.00 kg / square metre and pointed in white or coloured cement to match including rendering 10mm thick in cement plaster 1:3 including dismantling of old floor or wall tiling including cement mortar bedding and removing the rubbish outsidethe defence land complete all as specified and as directed. 34 material and labour for machine cut kota stone slab 20 25 mm thick ( size of each stone not less than 55cm x 55cm ) , laid in flooring, over and including cement screed bed 20mm thick in cement mortar ( 1:4 ) base set and jointed in neat cement slurry @ 3.00 kg / sqm and pointed in white or coloured cement to match the surface mixed with pigment to match shade of the slab over and including 25 mm thick cement concrete type b 0, 1:2:4 ( 12.5 mm graded aggregate ) as in levelling course, including cutting, waste, rubbing and polishing ( mirror finish ) including dismantling of existing stone slab / tiles etc including pcc and cement mortar bedding andrubbish off the premises complete all as specified and directed. 35 material and labour for machine cut kota stone slab 18 20 mm thick ( size of each stone not less than 55cm x 55cm ) , laid on vertical surfaces of skirting / dado, over and including cement screed bed 15 mm thick in cement mortar ( 1:3 ) and set and jointed in neat cement slurry @ 3.00 kg / sqm and pointed in white or coloured cement to match the surface mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing ( mirror finish ) including dismantling of existing stone slab / tiles etc including cement mortar bedding ( but not backing ) andrubbish off the premises complete all as specified and directed. 36 supply and fixing in repair of 5.5mm thick looking mirror of selected quality, beveled edge 450mmx600mm glass mounted on 6mm thick ac building board with aluminiumbeading andrubber packing and fixed to wall with wooden plug with chromium plated brass screw and cup washer complete all as specified and directed. 37 supply & fixing ( in repair ) vitreous china wash down water closet pedestal pattern ( ewc ) , white including connection to trap and to flushing pipe with ‘p’ or ‘s’ trap, making good to floor, plastic water closet seat cover with mild steel chromium plated hinges and chromium plated jet spray with 1.5 meter flexible ldpe pipe jointed with pipe complete all as specified and directed. 38 supply and fixing in repair of health faucet with 8mm dia, 1metre long flexible tube and wall hook complete all as specified and directed. 39 supply & fixing in repair of vitreous china wash hand basin white flat back of size 550x440mm including ci brackets and 15mm chromium plated pillar tap, pvc connection 450 mm long having ptmt nuts and 32 mm dia brass chromium plated waste coupling and making good to disturbed portion including32 mm dia pvc waste pipe etc., complete all as specified and directed. 40 supply and fixing in repair of 10 litre capacity virgin polypropylene cistern, white, isi marked, coloured at low level complete including supply and fixing45 cm pvc connection, pvc bend / flush pipe andmaking all connection , and removal old complete all as specified and directed. 41 supply and fixingin repair of vitreous china half stall urinal complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, pvc waste pipe, flush pipe, cp waste fitting, grating and union for discharge pipe complete all as specified and directed. 42 supply and fixing in repair of cp bib tap screwed down high pressure, long body, cast copper alloy, chromium plated with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified. ( note : weight of bib tap shall not be less than 0.575 kg ) 43 supply and fixing of gi tubing, isi marked, 15mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors including necassary cutting / chasing / pinning in wall and making good the disturbed surfaces as per existing whereever required, including taking down of old tubing as existing at site and removal, complete all as specified and as directed. 44 supply and fixing of gi tubing, isi marked, 20mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors including necassary cutting / chasing / pinning in wall and making good the disturbed surfaces as per existing whereever required, including taking down of old tubing as existing at site and removal, complete all as specified and as directed. 45 refixing old serviceable steel water tubing of 15 mm bore, in new or old position, any grade, including s&f new fittings as required, fixed to walls and ceilings or laying in floors including necassary cutting / chasing / pinning in wall and making good the disturbed surfaces as per existing whereever required , including taking down of old tubing as existing at site and removal, complete all as specified and as directed 46 refixing old serviceable steel water tubing of 20 mm bore, in new or old position, any grade, including s&f new fittings as required, fixed to walls and ceilings or laying in floors including necassary cutting / chasing / pinning in wall and making good the disturbed surfaces as per existing whereever required , including taking down of old tubing as existing at site and removal, complete all as specified and as directed 47 supply and fixing in repairs, water storage tank of 500 ltr capacity, hdpe double layer, isi marked, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, isi marked, screwed andsuitable for iron pipe 20 mm bore complete all as specified and directed. note: make of tank shall be engraved on the tank. 48 supply andfixing in repair of angle valve, 15mm dia chromium plated, cast copper alloy, screwed down, high pressure with capstain head, heavy with adjustable wall flange, and removal old complete all as specified and directed. 49 supply & fixed in repair of stop cock, fancy type, chromium plated, long shank and cup ( concealed type ) screwed down high pressure with crutch or butterfly handle screwed both ends suitable for 15mm bore pipe, complete all as specified and directed. ( note : weight of stop cock shall not be less than 0.575 kg ) 50 supply and fixingin repair of chromium plated shower rose with swivel joints and including fixed to gi tubing 15mm bore size of shower not less than 125mm complete all as specified and directed. 51 supply and fixing in repair of chromium plated soap dish with fitting fixed with brass screws complete all as specified and directed. 52 supply and fixing in repair of 20 mm dia gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all as specified and directed. 53 supply andfixing in repair of brass chromium plated tubular towel rail, 20 mm dia, ‘d’ type 60 cm long between flanges complete all as specified and directed. 54 excavating in trenches, not exceeding 1.50 m wide & not exceeding1.5m depth & getting out in hard / dense soil complete all as specified and directed. 55 supply and fixing of pvc ( swr ) 75 mm pipe single socket in any length with rubber ring joints laid in floor or trenches includingdismantling ofpipes of any description any length etc complete all as specified and as directed. 56 supply and fixing of pvc ( swr ) 110 mm pipe single socket in any length with rubber ring joints laid in floor or trenches includingdismantling ofpipes of any description any length etc complete all as specified and as directed. 57 supply and fixing of pvc ( swr ) 110 mm pipe single socket in any length with rubber ring joints fixed to wall with ms clamps including dismantling ofpipes of any description any length etc complete all as specified and as directed. 58 supply and fixingin repair of 110 mm bore pvc ( swr ) bend with access door including jointing with solvent cement, complete all as specified and directed. 59 supply and fixingin repair of pvc ( swr ) 110 mm to 75 mm dia, reducers complete all as specified and directed. 60 supply and fixing in repair of 110 mm bore pvc ( swr ) , junction single t ( equal or unequal ) , including jointing with solvent cement, complete all as specified and directed. 61 supply and fixing in repair of pvc ( swr ) floor trap 75mm dia plain with pvc grating including jointing with solvent cement complete all as specified and directed. 62 taking down chowkats or frames with shutter, areanot exceeding 1.50 square metre ( w / o taking off shutters from frames ) and removing from site, including cutting holes in wall / concrete for taking out existing hold fasts and making good the disturbed portion of jambs andadjoining surfacesin cm ( 1:3 ) and finishing the surfaces to match with existing finish complete all as specified and directed. 63 taking down chowkats or frames with shutter, areaexceeding 1.50 square metrebut not exceeding 4 square metre ( w / o taking off shutters from frames ) and removing from site, including cutting holes in wall / concrete for taking out existing hold fasts and making good the disturbed portion of jambs andadjoining surfacesin cm ( 1:3 ) and finishing the surfaces to match with existing finish complete all as specified and directed. 64 supply and fixing of pressed steel frames for doors of size 125 x 60mm, 1mm thick, with one or more rebates including, hold fasts of 25mm x 4mm fi, 25cm long, 6 nos in each chowkhat, necessary lugs, 3 nos 100 mm ms butt hinges medium weight, cold rolled, welded for each shutters of frame, lock strike plate, including sanding, tarring backs of chowkhats, pcc 1:3:6 type c 0filling in frame and for holdfast, 2 nos 12 mm dia ms tie bars at the bottom of frame and one shop coat of red oxide primer etc complete all as specified and as directed. 65 supplyand fixing of factory made 35 mm thick, second class hard wood rail and style, plain framed, panelled shutter ( two panel ) with lock rail and panel of 9 mm b.w.p commercial ply or 12 mm veneered particle board with commrcial veneering on both faces ace, size of rails and stiles asper is 1003 ( part i ) kiln seasoned and chemical pressure treated complete all as specified and directed. 66 supply and fixing of iind class ( hollock ) factory made 35mm thick glazed skelton door shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass / gauge etc. with sizes of members of shutters as specified in para 8.24 ( a ) of ssr 2009 ( part i ) , complete all as specified and directed. 67 supply and fixing factory of made pvc hollow door frame of size 50mm x 47mm with wall thickness of 5 mm made out of extended 5 mm rigid pvc foam sheet cut at corner and jointed with 02 nos, 150 mm long brackets of size 15 mm x 15 mm mild steel square tubes 19 gauge including vertical door profiles reinforced with 19 mm x 19 mm steel square tube of 19 gauge ( epdm ) rubber gasket weather seal provided through out the frame and fixed to wall with 65 / 100 mm long mild steel screws through the frame by using pvc fasteners ( minimum of 04 nos of screws to be provided for each vertical numbers & minimum 02 nos for horizontal member ) complete all as specified and directed. 68 supply andfixing factory made solid pvc moulded door shutter, 28 to 30 mm thick ( stiles ) with 2, 4 or 6 raised panel design with 2 mm thick moulded pvc sheet on the front face & 2 mm plain colour pvc sheet on back face includingfixing in frame at site with 03 nos ss hinges, 02 nos aluminium tower bolt 150 mm, 02 nos aluminium handle 150 mm for each shutter all as per specification & drawing complete all as specified and directed. 69 supply and fixing in repair of steel window box type using erw hollow p section comprising double frame for and including gauged and glazed skelton shutter 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs etc. all as shown on drawing no. td 219 ( c ) sheet 1 / 3 to 3 / 3 and td 220 ( c ) sheet 1 / 3 to 3 / 3 as applicable including pcc ( c o , 1:3:6 using 12.5 graded agg ) bed blocks for hold fasts and one shop coat of red oxide primer etc complete all as specified and directed.note: ( i ) for the purpose of measurement & payment double shutter with frame shall be considered as one unit. ( ii ) unit rate quoted against this item shall also include the iron mongery , grills 10mm square bars. ( iii ) only glazing, wire mesh & painting grill shall be measured & paid for separately ) 70 supply and fixingin repairs of mild steel ventilator of section framed fixed type and fixed wire mesh with flat bends 10 mm x 3 mm with nuts / bolts complete including fixing lugs, necessary pcc 1:3:6 type c 1 for filling bed blocks of hold fasts / lugs, etc complete all as specified and directed. 71 supply and fixing of mild steel pressed handle, 150mm long, oval type, stove enameled black, complete all as specified and directed. 72 supply and fixing of mild steel barrel tower bolt stove enamelled black with bright bolt 200mm long complete all as specified and directed. 73 supply and fixing of250 mm long mild steel sliding door bolts , plate type, stove enamelled black, with bright bolt not less than 12mm with and including a minimum of 6 bolts and nuts , four on bolt plate and two on staple plate complete all as specified and directed. 74 returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in soil complete all as specified and directed. 75 removing surplus excavated material ( soil ) to distance not exc. 50 m and depositing where directed at a level not exc. 1.50 m above the starting point complete all as specified and directed. 76 material and labour for pcc 1:3:6 type c 2 using 40mm graded mechanically crushed stone aggregate as in foundation filling, mass concrete, sub base etc. complete all as specified and directed 77 material and labour for plain cement concrete 1:2:4 type b 1 ( using 20mm graded mechanically crushed stone aggregate ) as in surface channels and drains, complete all as specified and as directed. 78 material and labour for pcc 1:2:4 type b 1 ( using 20 mm graded mechanically crushed stone aggregate ) ascopings, bed plates, kerbs, and other bands and the like, finished the surface fair andeven, including necessary form work etc including demolition of existing cement concrete of any description and in any position complete all as specified and directed. 79 material and labour for providing and laying of precast cement concrete solid concrete block, type b 1, 1:2:4 ( using 20mm graded stone aggreagate ) confirming to is 2185 ( part i ) 2005 of 30 cm high, 10 cm thick and of suitable width including chamfers, weatherings, throating etc as in kerb continuous edging jointed in cement mortar 1:4 and struck flush pointing as the work proceeds and finishing with neat cement flush joint etc complete all as specified and directed. 80 dismantling / taking down carefully aluminium / copper point wiring ( light, fan, socket or power ) complete, including fixtures and fittings such as switches, ceiling roses, pendants, regulators , sockets, light fittings etc., removing materials to stores for keeping in safe custody for taking credit and making good the disturbed surfaces of wall, floors, ceiling etc to match with the existing surfaces with matching obd / white wash / distemper complete all as specified and as directed. 81 material and labour for concealed point wiring with 1.50 sqmm single core pvc insulated, unsheathed cable frlsh, 1100 volt grade with multi stranded copper conductor drawn through and including medium grade, isi marked, pvc conduit not less than 25 mm dia with frlsh accessories, concealed and including provision of 1.50 sqmm single core pvc insulated, unsheathed cable frlsh 1100 volt grade with multi stranded copper conductorgreen colour as earth continuity conductor and connected to common earth dolly with suitable size of lugs, including mild steel sunken box or pressed steel terminal boxes made out of 1.6 mm thick mild steel sheet metal conforming to is 5139 ( pt i ) of 1969 and is:14772 2000 with earth dolly and coated with two coats of anti corrosive paint over a coat of red oxide primer bothinternally and externally including provision of new 3 mm thick plastic laminated sheet top cover extended up to 25 mm over sunken box for housing the switches , socket outlets, fan regulators etc. with brass screws and brass washersand making goodthe disturbed surfaces as per existing for one light / fan point / bell point controlled by one switch complete all as specified and directed. notes : ( i ) the quoted rates shall be deemed to be inclusive for cutting chases by chase cutter in wall / pillars / columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. the portion of point wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using necessary accessories / fittings. ( ii ) point wiring & earth wire shall be connected to each & every flush / sunken box. ( iii ) all screws, fasteners, bolts, nuts & washer shall be cadmium plated & the cost of which is deemed to be included in the quoted unit rates. 82 description all as per item no 81.00 above but for socket out let point 5 amps on same board complete all as specified and directed. 83 description all as per item no 81.00 above but for socket out let point 5 amps on independentboard complete all as specified and directed. 84 description all as per srl item no 81.00 above but point wiring for one socket out let 15&5 amps ( independent ) controlled by one switchwith using 2.5 sq mm ( nominal area ) stranded copper conductor complete all as specified and directed. 85 supply and fixing of switch piano 6 amps, flush type, single pole, one way, 230 volt , ac supply, isi marked, complete all as specified and directed. 86 supply and fixing of switch piano 15 amps flush type one way 230 volts, 50 hz, ac supply, isi marked, complete all as specified and directed. 87 supply and fixingsocket outlet 3 pin 5 amps, 230 volts flush type , isi marked, complete all as specified and directed. 88 supply and fixing of socket outlet 2 in 1, 6 / 16 amps, 5 pin 230 volt flush type, isi marked complete all as specified and directed. 89 supply and fixing of ceiling rose surface bakelite 65x50mm, 3 terminal complete all as specified and directed. 90 supply and fixing offan regulator electronic step type , 230 volts, ac supply, suitable for ceiling fan any type / make / sweep, complete all as specified and directed. 91 supply and fixing lamp holder, pvc / polycarbonate type with back plate suitable for batten fittings, complete all as specified. 92 supply and fixing of led lamp 9 watt suitable for batten holder complete all as specified and directed 93 supply and fixing of double stiff pendants, comprising of galvanised steel or chromium plated brass bell mouth connectors 2 nos. with back plate and 2×1.50 metre long parallel 20mm dia galvanised or stove enamelled screwed steel conduit with two check nuts for fixing tube light fitting and upto 1.5 metre long twin core 0.5 sq. mm copper conductor flexible wire / cable including disconnecting and taking down old existing light fitting of any description and in any position complete all as specified and directed. 94 supply and fixing of industrial box channel for fixing of led tube rod, in crca body suitable for 2x18 / 20 watt led tube, high efficient, ac 220 240 volts, 50 hz and connecting with copper conductor flexible cable of size 0.50 sqmm from ceiling rose to connector of the light including disconnecting and taking down old existing light fitting of any description and in any position complete all as specified and directed. note : ( i ) tube rod shall be measured and paid for separately. ( ii ) channel must be get approved from engr in charge to check fesibilty i.e. one end contact or two end contact. 95 supply and fixing of channel for fixing of led tube rod, in crca body suitable for 18 / 20 watt led tube, high efficient, ac 220 240 volts, 50 hz and connecting with copper conductor flexible cable of size 0.50 sqmm from ceiling rose to connector of the light including disconnecting and taking down old existing light fitting of any description and in any position complete all as specified and directed. note : ( i ) tube rod shall be measured and paid for separately. ( ii ) channel must be get approved from engr in charge to check fesibilty i.e. one end contact or two end contact. 96 supply and fixing of 18 w / 20w polycarbonate led tube light, environment friendly, high efficient, t8 with aluminium extrusion heat sink for optimum performance with high luminous efficiency and easy and taking down existing tube light and removal complete all as specified and directed. note: tube rod must be get approved from engineer in charge to check fesibilty i.e. one end contact or two end contact for fixing in existing led fittings. 97 supply and fixing ofbulk head light fitting, 15 watt, energy efficient withlamp 15 watt with provision of 2 / 3 core pvc copper conductor cable 0.5 sqmm size from ceiling rose to light fitting completeincluding disconnecting and taking down old existing light fitting of any description and in any position complete all as specified and directed. 98 supply and fixing in repair bracket for security light made up of 25mm dia, 0.9 metre long gi pipe, light grade, bent to required length, fixed to wall with two clamps made of 20 x 3 mm mild steel flat minimum 15cm long, 4 nos 8mm dia bolts with nuts complete all as specified and directed. 99 supply and fixing led security light luminaire 50 watt , pressure die cast aluminum housing, toughened heat resistant glass, ip65 protection, better optics for uniform distribution with multiplte leds not less than 2 w each and having optical grade polycarbonate lens with all accessories internally pre wired and including connecting up with two core 1.5 sq mmcopper conductor cable from connector to ceiling rose to connection of light including disconnecting and taking down oldunserviceable security light fitting of any description and in any position complete all as specified and directed. 100 supply and fixing led high efficient bay light 50 watt, die cast aluminum housing, toughened heat resistant glass, ip66 protection, better optics for uniform distribution with all accessories internally pre wired and including connecting up with two core 1.5 sq mmcopper conductor cable from connector to ceiling rose to connection of light including disconnecting and taking down oldunserviceable security light fitting of any description and in any position complete all as specified and directed. 101 supply and fixing of sheet metal enclosures vertical distribution board vtpn, ( mccb db ) 4 ways, double door, 415 volts with 200 amps rated bus bar ip 54 protection, with shrouded neutral bar and insulated bus bar and earth link, with and includingmccb 4 pole thermal release type, 100 amps, 16 kaas incomer and mcbsas out going complete with making suitable size of ms cabinet 2 mm thick dully grouted on the wall ( flush ) with opening arrangement including making connections with suitable size of lugs / thimbles / glands and making good the disturbed surface matching with existing surface including taking down existing unserviciable mccb / dbs including mcbs complete all as specified and directed. 102 supply, installation, testingofspn distibution board 8 way, double door , ip 43, as per is 8623including 200 amps fully insulated copper bus bar, insulated neutral bar, earth bar, door earthing, reversible doors, pan assembly for easy installation and also incoming and outgoing connections with suitable size of lugs / thimblesincluding taking down existing unserviciable mcb / dbs including mcbs complete all as specified and directed. 103 supply, installation, testingofspn distibution board 4 way, double door , ip 43, as per is 8623including 200 amps fully insulated copper bus bar, insulated neutral bar, earth bar, door earthing, reversible doors, pan assembly for easy installation and also incoming and outgoing connections with suitable size of lugs / thimblesincluding taking down existing unserviciable mcb / dbs including mcbs complete all as specified and directed. 104 supply and fixing of mcb single pole, 240 volts, 50hz , breaking capacity 10ka, b curve 6 to 32 amps, including connection with suitable size copper lugs complete all as specified and directed. 105 supply and fixing of mcb single pole, 240 volts, 50hz , breaking capacity 10ka, b curve 40 to 63 amps, including connection with suitable size copper lugs complete all as specified and directed. 106 supply and fixing of mcb single pole and neutral, 240 volts, 50hz , breaking capacity 10ka, b curve 40 to 63 amps, including connection with suitable size copper lugs complete all as specified and directed. 107 material and labour for concealed sub main wiring with two single core frlsh pvcinsulatedunsheathed copper conductor cable 2.5 sqmm drawnin and including rigid non metallic pvc medium grade 25 mm dia concealed conduit with accessories onwall or ceiling withone additional pvc insulated , strandedcopper conductor frlshof 2.5 sqmm, green colourfor earthcontinuity conductor including taking down old unserviceable sub main wiringand making good the disturbed surface complete all as specified and directed.note : 3 run of cable and 1 run ofconduit shall be measured as 1 unit. ( ii ) the quoted rates shall be deemed to be inclusive for cutting chasesin wall / pillars / columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. the portion of sub main wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using necessary aceessories / fittings. 108 material and labour for concealed sub main wiring with two single core frlsh pvcinsulatedunsheathed copper conductor cable 4.00 sqmm drawnin and including rigid non metallic pvc medium grade 25 mm dia concealed conduit with accessories onwall or ceiling withone additional pvc insulated , strandedcopper conductor frlshof 4.00 sqmm, green colourfor earthcontinuity conductor including taking down old unserviceable sub main wiringand making good the disturbed surface complete all as specified and directed.note : 3 run of cable and 1 run ofconduit shall be measured as 1 unit. ( ii ) the quoted rates shall be deemed to be inclusive for cutting chasesin wall / pillars / columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. the portion of sub main wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using necessary aceessories / fittings. 109 material and labour for concealed sub main wiring with two single core frlsh pvcinsulatedunsheathed copper conductor cable 6.00 sqmm drawnin and including rigid non metallic pvc medium grade 25 mm dia concealed conduit with accessories onwall or ceiling withone additional pvc insulated , strandedcopper conductor frlshof 6.00 sqmm, green colourfor earthcontinuity conductor including taking down old unserviceable sub main wiringand making good the disturbed surface complete all as specified and directed.note : 3 run of cable and 1 run ofconduit shall be measured as 1 unit. ( ii ) the quoted rates shall be deemed to be inclusive for cutting chasesin wall / pillars / columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface to match with the existing surface. the portion of sub main wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using necessary aceessories / fittings. 110 taking out of unserviceable earthing and material and labour for earthing and material & labour for earthing with galvanised steel earth plate electrode 60cmx 60cm x 6.0 mm thick buried directly in ground vertically at a depth not less than 2.25metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level, earth plate surrounded from all sides by 15cm thick packed layer ofcharcoal dust and common salt filling in alternate layers and electrode connections by usinggalvanised iron wire 4mmas earthing lead ( upto terminal point ) by means ofbolts, nuts, check nuts and washers made of galvanised iron and thimbles and protected by light grade 15 mm diagi pipe connected to main switch board or main control board and gi pipe medium grade 20mm bore for watering and including funnel , wire mesh, 50 mm thick precast rcc 1:2:4 type b1using 20 mm graded stone aggregate , reinforced with 8 mm dia dedormed / tmt bars 3 nos both way 12 mm dia round bar handle and pcc chamber pit with pcc ( 1:3:6 ) type c 2 using 40mm graded stone aggregate, including excavation and earth work in any type ofsoil , returning , filling in approved soil and disposal of surplus soil to a distance not exceeding 50m all as specified and shown in electrical plate no 3 ofssr 2009 ( part i ) complete all as specified and as directed. note : ( i ) earth lead wire and its protection pipe upto and including 7.50 mtr only from top of earth electrode are included under this item. ( ii ) on testing if the earth resistance is not obtained within permissible limit, earthing will be re done at no extra cost , till the desired earth resistance is obtained. ( iii ) any joint in earth lead from earth electrode to test point shall not be allowed / permitted. 111 supply, laying and testing of cable xlpe insulated, armoured heavy duty electric cable with standred aluminium conductor, 1100 volts grade, cross sectional area of size 25 sqmm 4 core including dismantling existing any type and any size cable complete all as specified and directed. 112 supply, laying and testing of cable xlpe insulated, armoured heavy duty electric cable with standred aluminium conductor, 1100 volts grade, cross sectional area of size 10 sqmm 2 core including dismantling existing any type and any size cable complete all as specified and directed. 113 supply and fixing in repair of gi protection pipe of 40mmdia light grade for cable protection including all fittings laid in trenches or fixed on pole, complete all as specified and as directed. 114 material and labour for supply and filling sand with clean dry fine sand unwashed including gently punning around cables in trenches for cable protection complete all as specified and directed. note: punned thickness shall be measurement & paid. 115 material and labour for brick protection covers over cable using sub class b old size brick laid along length of cable complete all as specified and directed. 116 supply and fixing 1100 volts grade heavy duty cable pvc insulated aluminium conductor, served with inner sheathing of pvc tape and overall pvc sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular of size 16sqmm including all incoming and outgoing connection with proper size of thimble including disconnecting and taking down existing cables etc. complete all as directed and specified. 117 supply and fixing in repair of house service bracket ( hook type ) complete with 3.0 m long gi pipe 40mm dia medium grade pipe, two 90 degree bends. ms hook, stay or guy including fixing clamps etc complete all as specified and directed. 118 note: amount of credit ofrs. 74, 062.00 for retrieved materials is mentioned in schedule of credit page no 19 & 20 of tender documents in pdf form which will be deducted offline while acceptance of tender....

Military Engineer Services - Haryana

31860672 comprehensive br repairs to joinery plumbing sanitary fittings and flooring items at 513 ad msl regt and 948 ad wksp of age br i south under ge south ambala cantt material andlabour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.11 sqm but not exceeding 0.18 sqm, 7 to 8 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg / square metre and pointed in white or coloured cement to match the surface over and including15mm thick screed bed or layer in cement mortar ( 1:4 ) including dismantling of existing tiles etc including cement mortar bedding ( but not backing ) andrubbish off the premises complete all as specified and directed. 2 material andlabour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.11 sqm but not exceeding 0.18 sqm, 7 to 8 mm thick as in vertical surfaces such as dado, skirting, set and jointed in neat cement slurry @ 3.00 kg / square metre and pointed in white or coloured cement to match the surface over and including 10 mm thick rendering in cement mortar ( 1:4 ) including dismantling of existing tiles etc including cement mortar bedding ( but not backing ) andrubbish off the premises complete all as specified and directed. 3 material & labour forpremium quality coloured glazed ceramic tiles ( 300x 450x 7mmthick ) in vertical surfacesand jointed in neat cement slurry and pointed in white or coloured cement to match including rendering 10mm thick in cement plaster 1:3 including dismantling of old floor or wall tiling including cement mortar bedding and removing the rubbish outsidethe defence land complete all as specified and as directed. 4 material & labour for 18 20 mm thickgranite stone slab of any type with table rubbed and polished as in slab / platforms and like set in cement mortar 1:4 including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match the shade of granite slabincluding dismantling of existing stone / tiles etc including cement mortar bedding andrubbish off the premises complete all as specified and directed. 5 material and labour for machine cut kota stone slab 20 25 mm thick ( size of each stone not less than 55cm x 55cm ) , laid in flooring, over and including cement screed bed 20mm thick in cement mortar ( 1:6 ) base set and jointed in neat cement slurry @ 3.00 kg / sqm and pointed in white or coloured cement to match the surface mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing ( granite finish ) including dismantling of existing stone / tiles etc including cement mortar bedding andrubbish off the premises complete all as specified and directed. 6 material and labour for machine cut kota stone slab 18 20 mm thick ( size of each stone not less than 55cm x 55cm ) , laid on vertical surfaces of skirting / dado, over and including cement screed bed 15 mm thick in cement mortar ( 1:4 ) and set and jointed in neat cement slurry @ 3.00 kg / sqm and pointed in white or coloured cement to match the surface mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing ( granite finish ) including dismantling of existing stone slab / tiles etc including cement mortar bedding ( but not backing ) andrubbish off the premises complete all as specified and directed. 7 matrerial and labour for 40mm thick average thicknesspcc ( 1:2:4 ) type b 0 using 12.5mm graded stone aggregate as in levelling course / paddingover roof surface, surface to be finished even and smooth with using extra cementincluding demolition of cement concrete ( unreinforced ) of any description and in any position not otherwise specifically provided for complete all as specified and directed. 8 material and labour for 100mm thickpcc1:3:6 type c 2 using 40mm graded aggregate as sub base of floor including demolition of cement concrete in ground floors and pavings n exc 15 cm thickness ( below or above ground level ) or complete all as specified and directed. 9 material and labour for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of m 35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size / shape, made by table vibratory method using pu mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified & as directed. 10 material and labour for plain cement concrete 1:2:4 type b 1 ( using 20 mm graded mechanically crushed stone aggregate ) asroof kerbs or mud stops and the like, rounded or chamfered on edges complete including demolition of cement concrete ( unreinforced ) of any description and in any position not otherwise specifically provided for complete all as specified and directed. 11 taking down cement plaster of any description and in any position including raking outfor keys, scrubbing down with water etc of any thikness & brick or stone wall etc. cement or cement lime plaster any description complete all as specified and directed. 12 material and labour for rendering 15 mm thick on fair face of brick work , concrete surfaces in cement mortar 1:6 finished even and smooth w / o extra cement complete all as specified and directed. 13 material and labour for rendering 15 mm thick on fair face of brick work , concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and directed. 14 material and labour for 10mm thick cement plaster in cm ( 1:3 ) to ceiling surfaceand finished the surface even and smooth without using extra cement with and including applyingthree coats of whitewash on ceiling complete all specified and directed. 15 material andlabour for preparation of exposed brick wall surface by cleaning the surface wire brush to remove all dirt / loose materials from the bricks and from the joints between the bricks. prepared surface should be then washed with diluted hcl acid ( dilution ratio of 1:50 ) for three times in a day for two days. after acid wash surface should be allowed to be air dried for one day. note : further treatment over the surface so achieved will be carried out only after approved of the same by ge. 16 material and labour for carrying out efflorescence treatment to unplastered wall surface comprising of the following specifications and sequence with and including 15 mm thick rendering in cm 1:4 finished even and smooth without using extra cement : ( a ) prime the prepared surface with one of the following product mixed with cement in 1:1 ratio as bonding agent : ( i ) pidicrete urp of m / s pidilite. ( ii ) sika latex of m / s sika. ( iii ) nitobond sbr latex of m / s fosroc. ( b ) immediately after priming the surface pmm ( polymer modified mortar ) to be applied “by hand” while the prime is tacky. pmm should be prepared by mixing one of the following compounds in cement mortar 1:3 as per manufacturer’s instructions: ( i ) pidicrete urp of m / s pidilite. ( ii ) sika latex of m / s sika. ( iii ) nitobond sbr latex of m / s fosroc. ( c ) pmm surface should be allowed to dry for one day. after that it should painted with two coats of one of the following compound mixed with cement only in ratio of 1 ( selected compound ) : 1:5 ( cement ) : ( i ) pidicrete urp of m / s pidilite. ( ii ) sika latex of m / s sika. ( iii ) nitobond sbr latex of m / s fosroc. ( d ) now apply two coats of one of the following compound over the surface. these compounds are to be used as per manufacturer’s instructions: ( i ) pidifin 2k of m / s pidilite. ( ii ) brush coat of m / s sika. ( iii ) brush bond of m / s fosroc.note : both coats should be perpendicular to each other and gap between two coats shall be minimum 6 hours. ( e ) sprinkle loose coarse sand after second coat while surface is tacky.note: ( i ) the item will be executed by authorized applicator only of the selected / approved company. contractor shall submit details of authorised applicator for approval of ge before commencement of work in respect of above item. ( ii ) every stage of work will be approved by ge, then only next layer will be executed by contractor. 17 material andlabour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper with hand roller, over a coat of alkaline resistant primer over a coat of birla wall care putty surface complete all as specified and directed. 18 material and labour for preparation of new plastered surfaces of any descriptionnot other wise described over 10 cm width or girth and applying two coats of cement base paint over a coat of alkali resistant primer on wall etc; complete all as specified and directed. 19 material and labour for preparation of old plastered or unplastered surfaces of walls by washing rubbing and applying one coat of oil bound distemper complete all as specified and as directed. 20 material and labour for preparation of old plastered or unplastered surfaces of walls by washing rubbing and applying one coat of cement base paint complete all as specified and as directed. 21 material and labour for preparation of old plastered or unplastered surfaces on ceiling by washing rubbing and applying one coat of white wash on ceiling complete all as specified and as directed. 22 material and labour for preparation of old wood and wooden based surfaces of any description not otherwise described over 10 cm in width or girth and applying one coat of synthetic enamel complete all as specified anddirected. 23 material and labour for preparation of old paint steel and iron surfaces of any description not otherwise described over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. 24 supply and fixing of gi tubing, isi marked, 15mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors including necassary cutting / chasing / pinning in wall and making good the disturbed surfaces as per existing whereever required, including taking down of old tubing as existing at site and removal, complete all as specified and as directed. 25 supply and fixing of gi tubing, isi marked, 20mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors including necassary cutting / chasing / pinning in wall and making good the disturbed surfaces as per existing whereever required, including taking down of old tubing as existing at site and removal, complete all as specified and as directed. 26 supply and fixing of water storage tank of 500 ltr capacity, hdpe triple layer, cylindrical, vertical with closed top and fda approved, 100% ua stabilized, rust proof, isi marked, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, isi marked, screwed andsuitable for iron pipe 20 mm bore including taking down of old tank of any descrption and removal from site complete all as specified and directed. note: tank shall be white and make of tank shall be engraved on the tank. 27 supply and fixing of water storage tank of 1000 ltr capacity, hdpe triple layer, cylindrical, vertical with closed top and fda approved, 100% ua stabilized, rust proof, isi marked, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, isi marked, screwed andsuitable for iron pipe 20 mm bore including taking down of old tank of any descrption and removal from site complete all as specified and directed. note: tank shall be white and make of tank shall be engraved on the tank. 28 supply and fixing in repair of 15mm fancy type, chromium plated, angle cock, cast copper alloy, screwed down high pressure with crutch or butterfly handle, heavy with adjustable wall flange, complete all as specified and directed. 29 supply and fixing in repair of stop cock, fancy type, chromium plated, long shank and cup ( concealed type ) screwed down high pressure with crutch or butterfly handle screwed both ends suitable for 15mm bore pipe, complete all as specified. ( note : weight of stop cock shall not be less than 0.575 kg ) ( note : weight of stop cock shall not be less than 0.575 kg ) 30 supply and fixing in repair ofcp bib tap screwed down high pressure, long body, cast copper alloy, chromium plated`with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified. ( note : weight of bib tap shall not be less than 0.575 kg ) 31 supply and fixing in repair of vitreous china squatting pan of orrisa pattern size 580 x 440mm white ( ist quality ) with ‘p’ or ’s’ trap, front or back inlet and foot rests of anypattern complete including provision of lime concrete bed and connection to flush pipe excluding flushing cistern, flush pipe and bracket and making good the disturbed area complete all as specified and directed. 32 supply and fixing ( in repair ) vitreous china wash down water closet pedestal pattern ( ewc ) , white including connection to trap and to flushing pipe with ‘p’ or ‘s’ trap, making good to floor, plastic water closet seat cover with mild steel chromium plated hinges and chromium plated jet spray with 1.5 meter flexible ldpe pipe jointed with pipe complete all as specified and directed. 33 supply and fixing ( in repair ) vitreous china wash hand basin white flat back of size 550x440mm including ci brackets and 15mm chromium plated pillar tap cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts, pvc connection 450 mm long having ptmt nuts and 32 mm dia brass chromium plated waste coupling and making good to disturbed portion including32 mm dia pvc waste pipe etc., complete all as specified and directed. 34 supply and fixing in repair of 10 litre capacity flush polypropylene cistern, isi marked, white at low level complete with pvc bend / flush pipe and making all connection including taking down existing high / low level cistern with all connections and making good the disturbed surfaces in cement mortar ( 1:3 ) to match with the existing surface, complete all as specified and directed. 35 supply and fixing in repair of chromium plated towel rail 600mm longcomplete all as specified and directed 36 supply and fixing in repair offancy type, shower rose 125mm size , brass chromium plated, revolving type, fixed to existing steel pipe or union 15mm bore complete all as specified and as directed. 37 supply and fixing in repair of aluminium ( die cast ) body door closer hydraulically regulated, designation no. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg complete all as specified and as directed. 38 supply and fixing in repair of vitreous china bowl urinal flat back, size of 465x355x265 mm white with grating and union for discharge pipe excluding flushing cistern, flush pipe and waste pipe, complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cementmortar 1:4 complete all as specified and as directed. 39 supply and fixing in repair of 32 / 40mm bore pvc waste pipesuitable for urinal / whb / sink etc complete all as specified and as directed. 40 supply and fixing in repair of pvc connections 45cm long and 15mm dia with ptmt nuts and pvc washers on both ends, complete all as specified and as directed. 41 supply and fixing in repair of pvc seat cover with hinges for ewccomplete all as specified and directed. 42 supply and fixing in repair of cp jet spray for with 1.5 mtr long pipefixed in ewc complete all as specified. 43 supply and fixing in repair of 100 / 75mm diacp grating any type fixed in floor and jointed in cm 1:3 complete all as specified and directed. 44 supply and fixing of pvc ( swr ) 110 mm pipe single socket in any length with rubber ring joints fixed to wall or infloors includingdismantling ofpipes of any description any length including bends etc complete all as specified and as directed. 45 supply and fixingg of pvc ( swr ) 75 mm pipe type socket in any length with rubber ring joints fixed to wall or infloors includingdismantling ofpipes of any description any length including bends etc complete all as specified and as directed. 46 supply and fixing of 110 mm bore pvc ( swr ) plain bend any radius including jointing with solvent cement, complete all as specified and as directed. 47 supply and fixing of 75 mm bore pvc ( swr ) plain bend any radius including jointing with solvent cement, complete all as specified and as directed. 48 supply and fixing in repair of 75mm dia of outlet, pvc ( swr ) floor trap plain with cp grating including jointing with solvent cement, complete all as specified and directed. 49 supply and fixing in repairs of 600mm x 450mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick ac bldg board or commercial plywood, fixedwith aluminium angled frame and two cp ms hanging arrangements complete all as specified and directed. 50 supply and fixing of 18 / 19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work as in , cup board shelves etc including dismantling boarding, any description, fixed in any position with nails etc; complete all as specified and directed. 51 taking down chowkats or frames with shutter, areanot exceeding 1.50 square metre ( w / o taking off shutters from frames ) and removing from site, including cutting holes in wall / concrete for taking out existing hold fasts and making good the disturbed portion of jambs andadjoining surfacesin cm ( 1:3 ) and finishing the surfaces to match with existing finish complete all as specified and directed. 52 taking down chowkats or frames with shutter, areaexceeding 1.50 square metrebut not exceeding 4 square metre ( w / o taking off shutters from frames ) and removing from site, including cutting holes in wall / concrete for taking out existing hold fasts and making good the disturbed portion of jambs andadjoining surfacesin cm ( 1:3 ) and finishing the surfaces to match with existing finish complete all as specified and directed. 53 taking down shutter of any descritption exc 1.00 sqm each but not exc 2.00 sqm each including removal from site complete all as specified and directed. 54 supply and fixing of pressed steel frames for doors of size 125 x 60mm, 1mm thick, with one or more rebates including, hold fasts of 25mm x 4mm fi, 25cm long, 6 nos in each chowkhat, necessary lugs, 3 nos 100 mm ms butt hinges medium weight, cold rolled, welded for each shutters of frame, lock strike plate, including sanding, tarring backs of chowkhats, pcc 1:3:6 type c 0filling in frame and for holdfast, 2 nos 12 mm dia ms tie bars at the bottom of frame and one shop coat of red oxide primer etc complete all as specified and as directed.. 55 supplyand fixing of factory made 35 mm thick, second class hard wood rail and style, plain framed, panelled shutter ( two panel ) with lock rail and panel of 9 mm b.w.p commercial ply or 12 mm veneered particle board with commrcial veneering on both faces ace, size of rails and stiles asper is 1003 ( part i ) kiln seasoned and chemical pressure treated complete all as specified and directed. 56 supply and fixing of iind class ( hollock ) factory made 35mm thick glazed skelton door shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass / gauge etc. with sizes of members of shutters as specified in para 8.24 ( a ) of ssr 2009 ( part i ) , complete all as specified and directed. 57 supply and fixing of factory made pvc hollow door frame of size 50 mm x 47 mm with wall thickness of 5 mm made out of extended 5 mm rigid pvc foam sheet cut at corner and jointed with 02 nos., 150 mm long brackets of size 15 mm x 15 mm mild steel square tubes 19 gauge including vertical door profiles reinforced with 19 mm x 19 mm steel square tube of 19 gauge ( epdm ) rubber gasket weather seal provided through out the frame and fixed to wall with 65 / 100 mm long mild steel screws through the frame by using pvc fasteners ( minimum of 04 nos. of screws to be provided for each vertical number & minimum 02 nos. for horizontal member ) , complete all as specified and directed. 58 supply and fixing of factory made solid pvc door shutter with wood free eps, 28 to 30mm thick ( stiles ) , with 2, 4, or 6 raised panel design with 2mm thick pvc sheet on the front face & 2mm plain colour pvc sheet on back face consisting of frame made out of m.s. tubes for top & bottom rails.m.s. frame shall be covered with heat moulded plain colour pvcc channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; panelling of plain colour pvc sheet to be fitted in the m.s. frame welded / sealed to the stiles & rails with suitable pvc sheet beading and jointed together with solvent cement , including supplying & fixing in the frame with 3 nos stainless steel butt hinges complete all as specified and as directed. 59 supply and fixing in repair of steel window box type using erw hollow p section comprising double frame for and including gauged and glazed skelton shutter 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs etc. all as shown on drawing no. td 219 ( c ) sheet 1 / 3 to 3 / 3 and td 220 ( c ) sheet 1 / 3 to 3 / 3 as applicable including pcc ( c o , 1:3:6 using 12.5 graded agg ) bed blocks for hold fasts and one shop coat of red oxide primer etc complete all as specified and directed.note: ( i ) for the purpose of measurement & payment double shutter with frame shall be considered as one unit. ( ii ) unit rate quoted against this item shall also include the iron mongery , grills 10mm square bars. ( iii ) only glazing, wire mesh & painting grill shall be measured & paid for separately ) 60 material and labour for preparing new or previously untreated wood or wooden surfaces of any description not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed. 61 material andlabour for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed. 62 supply and fixing of butt hinges, medium weight, cold rolled, mild steel, isi marked 100 mm sizecomplete all as specified and directed. 63 supply and fixing of 150mm long extruded aluminium alloy handles, fabricated type, anodised complete as specified and directed . 64 supply and fixing of aluminum anodized, barrel tower bolts of extruded section 200mm long complete all as specified and directed. 65 supply & fixing300 mmaluminum anodised sliding door bolts, isi marked, with hasp, staple ( bolt type ) complete with clamps bolt not less than 16mm dia and fixing clips of sheet, cast or extruded section and fixing bolts an sliding bolt of extruded section or cast aluminum alloy, all as specified. 66 supply andfixingof mild steel helical door spring 150 mm long fixed with screws to wooden chowkhats or welding to steel chowkhats, complete all as specified and directed. 67 supply andfixing of sheet glass 3mm thick, ordinary quality , in squarenot exceeding 0.5 square metre each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters, complete all as specified and as directed. 68 supply andfixingof galvanized steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staple complete all as specified and as directed. 69 supply andfixingin repair of mild steel helical door spring 150 mm long fixed with screws to wooden chowkhats or welding to steel chowkhats, complete all as specified and directed. 70 supply andfixing in repair of sheet glass 3mm thick, ordinary quality , in squarenot exceeding 0.5 square metre each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters, complete all as specified and as directed. 71 supply andfixingin repair of galvanized steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staple complete all as specified and as directed. 72 supply and fixingin repair of 150mm long floor door stopper of aluminium alloy body & tongue anodized with hard drawn steel spring complete all as specified and as directed.. 73 material and labourforrunning welding ( in repair ) thickness of metal to be welded exceeding 6mm but notexceeding 9mm complete all as specified and directed . 74 material and labour for brick work with sub class ‘b’ bricks, straight or curved on plain exceeding 6 metre mean radius in cement mortar ( 1:6 ) including demolition of brick work built in cement mortar including demolition of old brick / stone masonry built in cement mortar of any description including all quoins, archs, pillars etc complete all as specified and directed. 75 material and labour for brick work ( except bricks ) straight or curved on plan exceeding 6 metre mean radius built in cm 1:6 ( old size brick ) including demolition of old brick / stone masonry built in cement mortar of any description including all quoins, archs, pillars etc complete all as specified and directed. 76 cleaningand removing all scaleand dirt, etcfrom existing water storage tanks of capacityexceeding 500 litres andnot exceeding 1000 litres by emptying, drying and cleaning the tank by scrubbing the dust with wire brush from tank includingcleaning from mouths of circulating pipes, to entire satisfaction of engineer in–charge of cleaning, including writing date of cleaning with oil paint of of visible colour in font size not less than 100 mm high complete all as specified and directed. ( the rates includes for disconnecting of existing water tank, lowering if required and hoisting, reconnecting and refixing in same position after cleaning ) note: ( i ) the whole process ofdisconnecting, reconnecting and refixing in same position after cleaning shall be done on the same day, if failing so, rs. 100 / shall be deducted for each tank per day from the contractor due. ( ii ) a separate register to be maintained by contractor for cleaning and occupant signature with date to be obtained in it. 77 note: amount of credit ofrs. 48, 772.00 for retrieved materials is mentioned in schedule of credit page no 19 of tender documents in pdf form which will be deducted offline while acceptance of tender....

Military Engineer Services - Haryana

31860178 repair to flooring plinth protection plumbing sanitary fittings joinery and misc br items in md accn of yadunath vihar and yogendra enclave of age br i south under ge south ambala cantt material andlabour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.11 sqm but not exceeding 0.18 sqm, 7 to 8 mm thick as in floor, set and jointed in neat cement slurry @ 3.00 kg / square metre and pointed in white or coloured cement to match the surface over and including15mm thick screed bed or layer in cement mortar ( 1:4 ) including dismantling of existing tiles etc including cement mortar bedding ( but not backing ) andrubbish off the premises complete all as specified and directed. 2 material andlabour for premium quality, joint free, non skid coloured ceramic tiles, area of each tile exc 0.11 sqm but not exceeding 0.18 sqm, 7 to 8 mm thick as in vertical surfaces such as dado, skirting, set and jointed in neat cement slurry @ 3.00 kg / square metre and pointed in white or coloured cement to match the surface over and including 10 mm thick rendering in cement mortar ( 1:4 ) including dismantling of existing tiles etc including cement mortar bedding ( but not backing ) andrubbish off the premises complete all as specified and directed. 3 material & labour forpremium quality coloured glazed ceramic tiles ( 300x 450x 7mmthick ) in vertical surfacesand jointed in neat cement slurry and pointed in white or coloured cement to match including rendering 10mm thick in cement plaster 1:3 including dismantling of old floor or wall tiling including cement mortar bedding and removing the rubbish outsidethe defence land complete all as specified and as directed. 4 material & labour for 18 20 mm thickgranite stone slab of any type with table rubbed and polished as in slab / platforms and like set in cement mortar 1:4 including pointing in white cement ( 1:2 ) using marble dust with admixture of pigment to match the shade of granite slabincluding dismantling of existing stone / tiles etc including cement mortar bedding andrubbish off the premises complete all as specified and directed. 5 material and labour for machine cut kota stone slab 20 25 mm thick ( size of each stone not less than 55cm x 55cm ) , laid in flooring, over and including cement screed bed 20mm thick in cement mortar ( 1:6 ) base set and jointed in neat cement slurry @ 3.00 kg / sqm and pointed in white or coloured cement to match the surface mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing ( granite finish ) including dismantling of existing stone / tiles etc including cement mortar bedding andrubbish off the premises complete all as specified and directed. 6 material and labour for machine cut kota stone slab 18 20 mm thick ( size of each stone not less than 55cm x 55cm ) , laid on vertical surfaces of skirting / dado, over and including cement screed bed 15 mm thick in cement mortar ( 1:4 ) and set and jointed in neat cement slurry @ 3.00 kg / sqm and pointed in white or coloured cement to match the surface mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing ( granite finish ) including dismantling of existing stone slab / tiles etc including cement mortar bedding ( but not backing ) andrubbish off the premises complete all as specified and directed. 7 mterial and labour for pcc 1:4:8 type d 2 ( using 40 mm grade stone aggregate ) as in floor filling & mass concrete for sunken floor in wc / bath etc including demolition of cement concrete ( unreinforced ) of any description and in any position not otherwise specifically provided for complete all as specified and directed. 8 material and labour for water proofing treatment of sunken floor of wcs, bathroom, etc by applyingof the following specifications and sequence with and including 40mm thick pcc 1:2:4 type b 1 using 20mm graded aggregate as in floor rough finishescomplete as specified and directed: ( i ) cleaning of sunken floor surface with mechanical means i.e. wire brush / air blower etc. andremove all loose / unsound material, dirt, dust etc. ( ii ) applying cement slurry mixed with acrylic based polymer moodified cementitous composite compound coating. ( iii ) first layer of cement slurry @ 0.488kg / sqm mixed with acrylic based polymer moodified cementitous composite compound @0.253 kg / sqm and allow it to air dry for 04 hours. ( iv ) second layer of cement slurry @ 0.242 kg / sqm mixed with acrylic based polymer moodified cementitous composite compound @0.126kg / sqm and allow it to air dry for 04 hours followed with water curing for 48 hours. ( v ) 200 micron thick polythene film shall be pasted with help of adhesives over treatment.note joints of wc / trap / soil waste shall be properly sealed with sealing compound. testing of all traps and joint and sunken slab shall be done as per is 1742 before filling and tiling work. 9 matrerial and labour for 40mm thick average thicknesspcc ( 1:2:4 ) type b 0 using 12.5mm graded stone aggregate as in levelling course / paddingover roof surface, surface to be finished even and smooth with using extra cementincluding demolition of cement concrete ( unreinforced ) of any description and in any position not otherwise specifically provided for complete all as specified and directed. 10 material and labour for 100mm thickpcc1:3:6 type c 2 using 40mm graded aggregate as sub base of floor including demolition of cement concrete in ground floors and pavings n exc 15 cm thickness ( below or above ground level ) or complete all as specified and directed. 11 material and labour for providing and laying 60mm thick factory made chamfered edge cement concrete paver block of m 35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size / shape, made by table vibratory method using pu mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding / laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified & as directed. 12 material and labour for plain cement concrete 1:2:4 type b 1 ( using 20 mm graded mechanically crushed stone aggregate ) asroof kerbs or mud stops and the like, rounded or chamfered on edges complete including demolition of cement concrete ( unreinforced ) of any description and in any position not otherwise specifically provided for complete all as specified and directed. 13 taking down cement plaster of any description and in any position including raking outfor keys, scrubbing down with water etc of any thikness & brick or stone wall etc. cement or cement lime plaster any description complete all as specified and directed. 14 material and labour for rendering 15 mm thick on fair face of brick work , concrete surfaces in cement mortar 1:6 finished even and smooth w / o extra cement complete all as specified and directed. 15 material and labour for rendering 15 mm thick on fair face of brick work , concrete surfaces in cement mortar 1:4 finished even and smooth without using extra cement complete all as specified and directed. 16 material and labour for 10mm thick cement plaster in cm ( 1:3 ) to ceiling surfaceand finished the surface even and smooth without using extra cement with and including applyingthree coats of whitewash on ceiling complete all specified and directed. 17 material andlabour for preparation of exposed brick wall surface by cleaning the surface wire brush to remove all dirt / loose materials from the bricks and from the joints between the bricks. prepared surface should be then washed with diluted hcl acid ( dilution ratio of 1:50 ) for three times in a day for two days. after acid wash surface should be allowed to be air dried for one day. note : further treatment over the surface so achieved will be carried out only after approved of the same by ge. 18 material and labour for carrying out efflorescence treatment to unplastered wall surface comprising of the following specifications and sequence with and including 15 mm thick rendering in cm 1:4 finished even and smooth without using extra cement : ( a ) prime the prepared surface with one of the following product mixed with cement in 1:1 ratio as bonding agent : ( i ) pidicrete urp of m / s pidilite. ( ii ) sika latex of m / s sika. ( iii ) nitobond sbr latex of m / s fosroc. ( b ) immediately after priming the surface pmm ( polymer modified mortar ) to be applied “by hand” while the prime is tacky. pmm should be prepared by mixing one of the following compounds in cement mortar 1:3 as per manufacturer’s instructions: ( i ) pidicrete urp of m / s pidilite. ( ii ) sika latex of m / s sika. ( iii ) nitobond sbr latex of m / s fosroc. ( c ) pmm surface should be allowed to dry for one day. after that it should painted with two coats of one of the following compound mixed with cement only in ratio of 1 ( selected compound ) : 1:5 ( cement ) : ( i ) pidicrete urp of m / s pidilite. ( ii ) sika latex of m / s sika. ( iii ) nitobond sbr latex of m / s fosroc. ( d ) now apply two coats of one of the following compound over the surface. these compounds are to be used as per manufacturer’s instructions: ( i ) pidifin 2k of m / s pidilite. ( ii ) brush coat of m / s sika. ( iii ) brush bond of m / s fosroc.note : both coats should be perpendicular to each other and gap between two coats shall be minimum 6 hours. ( e ) sprinkle loose coarse sand after second coat while surface is tacky.note: ( i ) the item will be executed by authorized applicator only of the selected / approved company. contractor shall submit details of authorised applicator for approval of ge before commencement of work in respect of above item. ( ii ) every stage of work will be approved by ge, then only next layer will be executed by contractor. 19 material andlabour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper with hand roller, over a coat of alkaline resistant primer over a coat of birla wall care putty surface complete all as specified and directed. 20 material and labour for preparation of new plastered surfaces of any descriptionnot other wise described over 10 cm width or girth and applying two coats of cement base paint over a coat of alkali resistant primer on wall etc; complete all as specified and directed. 21 material and labour for preparation of old plastered or unplastered surfaces of walls by washing rubbing and applying one coat of oil bound distemper complete all as specified and as directed. 22 material and labour for preparation of old plastered or unplastered surfaces of walls by washing rubbing and applying one coat of cement base paint complete all as specified and as directed. 23 material and labour for preparation of old plastered or unplastered surfaces on ceiling by washing rubbing and applying one coat of white wash on ceiling complete all as specified and as directed. 24 material and labour for preparation of old wood and wooden based surfaces of any description not otherwise described over 10 cm in width or girth and applying one coat of synthetic enamel complete all as specified anddirected. 25 material and labour for preparation of old paint steel and iron surfaces of any description not otherwise described over 10 cm in width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. 26 supply and fixing of gi tubing, isi marked, 15mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors including necassary cutting / chasing / pinning in wall and making good the disturbed surfaces as per existing whereever required, including taking down of old tubing as existing at site and removal, complete all as specified and as directed. 27 supply and fixing of gi tubing, isi marked, 20mm bore, `medium grade, with all fittings and fixed complete to walls and ceilings or laid in floors including necassary cutting / chasing / pinning in wall and making good the disturbed surfaces as per existing whereever required, including taking down of old tubing as existing at site and removal, complete all as specified and as directed. 28 supply and fixing of water storage tank of 500 ltr capacity, hdpe triple layer, cylindrical, vertical with closed top and fda approved, 100% ua stabilized, rust proof, isi marked, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, isi marked, screwed andsuitable for iron pipe 20 mm bore including taking down of old tank of any descrption and removal from site complete all as specified and directed. note: tank shall be white and make of tank shall be engraved on the tank. 29 supply and fixing of water storage tank of 1000 ltr capacity, hdpe triple layer, cylindrical, vertical with closed top and fda approved, 100% ua stabilized, rust proof, isi marked, fixed and hoisted in position on staging or roof complete with locking arrangement including over flow pipe, air lock pipe, brass valve 20 mm high pressure with polythene float and flynut, isi marked, screwed andsuitable for iron pipe 20 mm bore including taking down of old tank of any descrption and removal from site complete all as specified and directed. note: tank shall be white and make of tank shall be engraved on the tank. 30 supply and fixing in repair of 15mm fancy type, chromium plated, angle cock, cast copper alloy, screwed down high pressure with crutch or butterfly handle, heavy with adjustable wall flange, complete all as specified and directed. 31 supply and fixing in repair of stop cock, fancy type, chromium plated, long shank and cup ( concealed type ) screwed down high pressure with crutch or butterfly handle screwed both ends suitable for 15mm bore pipe, complete all as specified. ( note : weight of stop cock shall not be less than 0.575 kg ) ( note : weight of stop cock shall not be less than 0.575 kg ) 32 supply and fixing in repair ofcp bib tap screwed down high pressure, long body, cast copper alloy, chromium plated`with crutch or butterfly handles screwed down suitable for 15mm bore pipe or union, complete all as specified. ( note : weight of bib tap shall not be less than 0.575 kg ) 33 supply and fixing in repair of vitreous china squatting pan of orrisa pattern size 580 x 440mm white ( ist quality ) with ‘p’ or ’s’ trap, front or back inlet and foot rests of anypattern complete including provision of lime concrete bed and connection to flush pipe excluding flushing cistern, flush pipe and bracket and making good the disturbed area complete all as specified and directed. 34 supply and fixing ( in repair ) vitreous china wash down water closet pedestal pattern ( ewc ) , white including connection to trap and to flushing pipe with ‘p’ or ‘s’ trap, making good to floor, plastic water closet seat cover with mild steel chromium plated hinges and chromium plated jet spray with 1.5 meter flexible ldpe pipe jointed with pipe complete all as specified and directed. 35 supply and fixing ( in repair ) vitreous china wash hand basin white flat back of size 550x440mm including ci brackets and 15mm chromium plated pillar tap cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts, pvc connection 450 mm long having ptmt nuts and 32 mm dia brass chromium plated waste coupling and making good to disturbed portion including32 mm dia pvc waste pipe etc., complete all as specified and directed. 36 supply and fixing in repair of 10 litre capacity flush polypropylene cistern, isi marked, white at low level complete with pvc bend / flush pipe and making all connection including taking down existing high / low level cistern with all connections and making good the disturbed surfaces in cement mortar ( 1:3 ) to match with the existing surface, complete all as specified and directed. 37 supply and fixing in repair of fancy type pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered hot or cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as directed. 38 supply and fixing in repair of chromium plated towel rail 600mm longcomplete all as specified and directed 39 supply and fixing in repair offancy type, shower rose 125mm size , brass chromium plated, revolving type, fixed to existing steel pipe or union 15mm bore complete all as specified and as directed. 40 supply and fixing in repair of 32 / 40mm bore pvc waste pipesuitable for urinal / whb / sink etc complete all as specified and as directed. 41 supply and fixing in repair of pvc connections 45cm long and 15mm dia with ptmt nuts and pvc washers on both ends, complete all as specified and as directed. 42 supply and fixing in repair of pvc seat cover with hinges for ewccomplete all as specified and directed. 43 supply and fixing in repair of cp jet spray for with 1.5 mtr long pipefixed in ewc complete all as specified. 44 supply and fixing in repair of 100 / 75mm diacp grating any type fixed in floor and jointed in cm 1:3 complete all as specified and directed. 45 supply and fixing of pvc ( swr ) 110 mm pipe single socket in any length with rubber ring joints fixed to wall or infloors includingdismantling ofpipes of any description any length including bends etc complete all as specified and as directed. 46 supply and fixingg of pvc ( swr ) 75 mm pipe type socket in any length with rubber ring joints fixed to wall or infloors includingdismantling ofpipes of any description any length including bends etc complete all as specified and as directed. 47 supply and fixing of 110 mm bore pvc ( swr ) plain bend any radius including jointing with solvent cement, complete all as specified and as directed. 48 supply and fixing of 75 mm bore pvc ( swr ) plain bend any radius including jointing with solvent cement, complete all as specified and as directed. 49 supply and fixing in repair of 75mm dia of outlet, pvc ( swr ) floor trap plain with cp grating including jointing with solvent cement, complete all as specified and directed. 50 supply and fixing in repairs of 600mm x 450mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick ac bldg board or commercial plywood, fixedwith aluminium angled frame and two cp ms hanging arrangements complete all as specified and directed. 51 supply and fixing of 18 / 19 mm thick prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work as in , cup board shelves etc including dismantling boarding, any description, fixed in any position with nails etc; complete all as specified and directed. 52 taking down chowkats or frames with shutter, areanot exceeding 1.50 square metre ( w / o taking off shutters from frames ) and removing from site, including cutting holes in wall / concrete for taking out existing hold fasts and making good the disturbed portion of jambs andadjoining surfacesin cm ( 1:3 ) and finishing the surfaces to match with existing finish complete all as specified and directed. 53 taking down chowkats or frames with shutter, areaexceeding 1.50 square metrebut not exceeding 4 square metre ( w / o taking off shutters from frames ) and removing from site, including cutting holes in wall / concrete for taking out existing hold fasts and making good the disturbed portion of jambs andadjoining surfacesin cm ( 1:3 ) and finishing the surfaces to match with existing finish complete all as specified and directed. 54 taking down shutter of any descritption exc 1.00 sqm each but not exc 2.00 sqm each including removal from site complete all as specified and directed. 55 supply and fixing of pressed steel frames for doors of size 125 x 60mm, 1mm thick, with one or more rebates including, hold fasts of 25mm x 4mm fi, 25cm long, 6 nos in each chowkhat, necessary lugs, 3 nos 100 mm ms butt hinges medium weight, cold rolled, welded for each shutters of frame, lock strike plate, including sanding, tarring backs of chowkhats, pcc 1:3:6 type c 0filling in frame and for holdfast, 2 nos 12 mm dia ms tie bars at the bottom of frame and one shop coat of red oxide primer etc complete all as specified and as directed.. 56 supplyand fixing of factory made 35 mm thick, second class hard wood rail and style, plain framed, panelled shutter ( two panel ) with lock rail and panel of 9 mm b.w.p commercial ply or 12 mm veneered particle board with commrcial veneering on both faces ace, size of rails and stiles asper is 1003 ( part i ) kiln seasoned and chemical pressure treated complete all as specified and directed. 57 supply and fixing of iind class ( hollock ) factory made 35mm thick glazed skelton door shutters, open rebated and prepared to receive glass, gauge etc. divided into squares edges of framing, plain, chamfered or rounded, mitred fitted with cut and mitred beads for securing glass / gauge etc. with sizes of members of shutters as specified in para 8.24 ( a ) of ssr 2009 ( part i ) , complete all as specified and directed. 58 supply and fixing of factory made pvc hollow door frame of size 50 mm x 47 mm with wall thickness of 5 mm made out of extended 5 mm rigid pvc foam sheet cut at corner and jointed with 02 nos., 150 mm long brackets of size 15 mm x 15 mm mild steel square tubes 19 gauge including vertical door profiles reinforced with 19 mm x 19 mm steel square tube of 19 gauge ( epdm ) rubber gasket weather seal provided through out the frame and fixed to wall with 65 / 100 mm long mild steel screws through the frame by using pvc fasteners ( minimum of 04 nos. of screws to be provided for each vertical number & minimum 02 nos. for horizontal member ) , complete all as specified and directed. 59 supply and fixing of factory made solid pvc door shutter with wood free eps, 28 to 30mm thick ( stiles ) , with 2, 4, or 6 raised panel design with 2mm thick pvc sheet on the front face & 2mm plain colour pvc sheet on back face consisting of frame made out of m.s. tubes for top & bottom rails.m.s. frame shall be covered with heat moulded plain colour pvcc channel having a pvc sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour pvc sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail ; panelling of plain colour pvc sheet to be fitted in the m.s. frame welded / sealed to the stiles & rails with suitable pvc sheet beading and jointed together with solvent cement , including supplying & fixing in the frame with 3 nos stainless steel butt hinges complete all as specified and as directed. 60 supply and fixing in repair of steel window box type using erw hollow p section comprising double frame for and including gauged and glazed skelton shutter 30mm thick, jointed internally with flat iron 25x3mm complete including hinges, handle, tower bolts, stops, lugs etc. all as shown on drawing no. td 219 ( c ) sheet 1 / 3 to 3 / 3 and td 220 ( c ) sheet 1 / 3 to 3 / 3 as applicable including pcc ( c o , 1:3:6 using 12.5 graded agg ) bed blocks for hold fasts and one shop coat of red oxide primer etc complete all as specified and directed.note: ( i ) for the purpose of measurement & payment double shutter with frame shall be considered as one unit. ( ii ) unit rate quoted against this item shall also include the iron mongery , grills 10mm square bars. ( iii ) only glazing, wire mesh & painting grill shall be measured & paid for separately ) 61 material and labour for preparing new or previously untreated wood or wooden surfaces of any description not otherwise described over 10 cm in width or girth and applying two coats of synthetic enamel paint over one coat of pink primer complete all as specified and as directed. 62 material andlabour for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed. 63 supply and fixing of butt hinges, medium weight, cold rolled, mild steel, isi marked 100 mm sizecomplete all as specified and directed. 64 supply and fixing of 150mm long extruded aluminium alloy handles, fabricated type, anodised complete as specified and directed . 65 supply and fixing of aluminum anodized, barrel tower bolts of extruded section 200mm long complete all as specified and directed. 66 supply & fixing300 mmaluminum anodised sliding door bolts, isi marked, with hasp, staple ( bolt type ) complete with clamps bolt not less than 16mm dia and fixing clips of sheet, cast or extruded section and fixing bolts an sliding bolt of extruded section or cast aluminum alloy, all as specified. 67 supply andfixingof mild steel helical door spring 150 mm long fixed with screws to wooden chowkhats or welding to steel chowkhats, complete all as specified and directed. 68 supply andfixing of sheet glass 3mm thick, ordinary quality , in squarenot exceeding 0.5 square metre each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters, complete all as specified and as directed. 69 supply andfixingof galvanized steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staple complete all as specified and as directed. 70 supply andfixingin repair of mild steel helical door spring 150 mm long fixed with screws to wooden chowkhats or welding to steel chowkhats, complete all as specified and directed. 71 supply andfixing in repair of sheet glass 3mm thick, ordinary quality , in squarenot exceeding 0.5 square metre each pane and glazing with oil putty to steel window and with wooden beads to wooden shutters, complete all as specified and as directed. 72 supply andfixingin repair of galvanized steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm fixed with tinned tacks or galvanized wire staple complete all as specified and as directed. 73 supply and fixingin repair of 150mm long floor door stopper of aluminium alloy body & tongue anodized with hard drawn steel spring complete all as specified and as directed.. 74 material and labourforrunning welding ( in repair ) thickness of metal to be welded exceeding 6mm but notexceeding 9mm complete all as specified and directed . 75 material and labour for brick work with sub class ‘b’ bricks, straight or curved on plain exceeding 6 metre mean radius in cement mortar ( 1:6 ) including demolition of brick work built in cement mortar including demolition of old brick / stone masonry built in cement mortar of any description including all quoins, archs, pillars etc complete all as specified and directed. 76 material and labour for brick work ( except bricks ) straight or curved on plan exceeding 6 metre mean radius built in cm 1:6 ( old size brick ) including demolition of old brick / stone masonry built in cement mortar of any description including all quoins, archs, pillars etc complete all as specified and directed. 77 cleaningand removing all scaleand dirt, etcfrom existing water storage tanks of capacityexceeding 500 litres andnot exceeding 1000 litres by emptying, drying and cleaning the tank by scrubbing the dust with wire brush from tank includingcleaning from mouths of circulating pipes, to entire satisfaction of engineer in–charge of cleaning, including writing date of cleaning with oil paint of of visible colour in font size not less than 100 mm high complete all as specified and directed. ( the rates includes for disconnecting of existing water tank, lowering if required and hoisting, reconnecting and refixing in same position after cleaning ) note: ( i ) the whole process ofdisconnecting, reconnecting and refixing in same position after cleaning shall be done on the same day, if failing so, rs. 100 / shall be deducted for each tank per day from the contractor due. ( ii ) a separate register to be maintained by contractor for cleaning and occupant signature with date to be obtained in it. 78 material andlabour for 6 mm thick asbestos cement sheet, corrugated, or semi corrugated sheets in roofs, walls etc. and fixed with l hook or cranked bolts in patches including dismantling old asbestos cement corrugated or semi corrugated sheets, complete all as specified and directed. 79 note: amount of credit ofrs. 95, 184.00 for retrieved materials is mentioned in schedule of credit page no 19 of tender documents in pdf form which will be deducted offline while acceptance of tender....

Military Engineer Services - Haryana

30428761 repair replace of steel window vents and hacking broken window glass for replace with acrylic transparent sheet incl attend day to day emergent complaint of plumbing carpentry and joinery nature of otm accn zone a , b in aor age br i under ge hisar ca no ge ( h ) 53 / 2021 22...

Military Engineer Services - Haryana

30393425 repair replace of steel window vents hacking and broken window glass for replace with acrylic transparent sheet incl attend day to day emergent complaint of plumbing, carpentry and joinery nature of otm accn zone c in the aor age br i under ge hisar repair replace of steel window vents hacking and broken window glass for replace with acrylic transparent sheet incl attend day to day emergent complaint of plumbing, carpentry and joinery nature of otm accn zone c in the aor age br i under ge hisar...

Military Engineer Services - Haryana

28290592 repair replace steel window ventilator and hacking out broken window glass for replace with acrylic sheet incl attend day to day emergent complaint of plumbing , carpentry , joinery of md accn dstv south and north in aor of age br i under ge hisar ca no ge ( h ) 18/2021 22...

Haryana Police Housing Corporation Limited - Haryana

24041160 providing 40 kva dg set and allied items for stp manesar distt . gurugram 2 earth work in excavation in foundations, trenches, etc. in all kinds of soils, not exceeding 2 metres depth including dressing of bottom and sides of trenches, stacking the excavated soil, clear from the edge of excavation and subsequent filling around masonry, in 15 cm layers with compaction, including disposal of all surplus soil, as directed within a lead of 30 metres. ( hsr 6.6 +cp 425% ) 3 cement concrete 1 : 6 : 12 with brick ballast 40 mm nominal size in foundation and plinth. ( hsr 10.30+cp 450% ) 4 cement concrete 1 : 1.5 : 3 with stone aggregate 20 mm nominal sie in foundation and plinth.. ( hsr 10.42+cp 450% ) 5 first class brick work laid in cement sand mortar 1:4 in foundation and plinth. ( hsr 11.4 ( c.p.@ 650 % ) 6 12 mm thick cement plaster 1:4. ( hsr 15.5 +cp 600% ) 7 painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade. ( hsr 16.3+cp 230% ) ist quality 8 applying priming coat with metal primer on new steel or iron work including preparation of surface. ( hsr 16.9+cp 230% ) ist quality 9 wrought iron and mild steel ( using angles, flats square bars, tees and channels ) ladders, grills, gratting frames, window guards, iron doors openable or fixed stair case or parapet or any other type of railing, gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position. ( hsr 18.12+cp 500% ) 10 providing and fixing hard drawn steel wire fabric 75 mm x 25 mm rectangular mesh with 3.25 mm dia wire fixed on steel windows of standard rolled sections with 3 mm thick flat iron cover moulding of 12.5 mm width fixed with machine screws welded complete in all respect. ( hsr 18.33+cp 500% ) 11 supplying, hoisting and placing in position tubular trusses including runners, purlins, consisting of steel tubes conforming to i.s. specifications of tested quality duly welded with fillet welds 6 mm thick through out including wind bracing. open end of pipe sealed with 3 mm thick plate including the cost of nuts and bolts where bolts connections are specified at flange joints including one coat of ready mixed red oxide zink cromate primer of approved quality assembling and fixed in positon complete in all respect. ( hsr 18.14+cp 500% ) 12 earthing. ( hsr 31.22+cp 350% ) 13 iii ) earthing with gi earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) complete as equired. 14 iv ) earthing with tinned copper earth plate 600 mm x 600 mm x 3 mm thick including accessories and providing masonry enclosures with cover plate having locking arrangement and watering pipe etc. ( but without charcoal or coke and salt ) comlete as equired. 15 v ) extra for charcoal or coke and salt for g.i. plate or copper plate earth electrode. 16 x ) providing and fixing 25 mm x 5 mm copper strip in 40 mm dia g.i. pipe from earth electrode as required. 17 xi ) providing and fixing 25 mm x 5 mm gi strip in 40 mm dia g.i pipe from earth electrode as required. 18 xiv ) pdg. and fixing 25 mm x 5 mm copper strip on surface or in recess for connections etc. as required with all labour and material. 19 xv ) pdg. and fixing 25 mm x 5 mm g.i. strip on surface or in recess for connections etc. as required with all labour and material. 20 s / e of under ground cable loose in existing pipe or trenches including necessary connection, digging and refilling of trenches. ( hsr 31.26+cp 140% ) xxvii ) 50 sq. mm 3.5 core cable ( armoured ) 21 supply and erection of suitable compression type brass cable glands for underground cable. ( hsr 31.28+cp 140% ) iv ) 70 sqmm to 95 sqmm cable 3 to 3.5 core . iii ) 25 sqmm to 50 sqmm cable 2 to 4 22 miscellaneous. ( hsr 31.35+cp 130% ) ( ix ) supply and erection of aluminium lugs heavy duty including crimping etc. upto the entire satisfaction of the engineer in charge of the work. e ) 25 sqmm . 23 g ) 50 sqmm 24 supply, installation, testing and commissioning of wall / free standing floor mounting dust and vermin proof compartmentalized cubical panel made out of 2 mm thick crca sheet, required hardware 3mm thick bakelite sheet provided all along the bus bar and cable alley separating switches compartment and supporting suitable channel duly painted by 2 coat of zinc / red oxide primer followed by 2 coats of powder coating in grey or required shade after rinsing. the panel having pu / neoprene rubber gasket of not less than 3mm thickness separate detachable gland plate ms base channel hinged door with inter locking arrangement for equipment / switch wear.transparent acrylic sheet shall be provided in front of bus bar compartment to prevent direct access to bus bar bakelite sheet 3mm thick for separately cable alloey to bbc from switch chamber extended solid copper bars up to cable alleys shall be provided for outgoing connection which shall be paid as extra items. side walls and cable alley compartments shall be having bolted type doors with detachable extension type structure. the panel will be complete with control wiring ( copper ) and fuse protection ( only outer area on all sides shall be measured ) as per hsr 31.63 ( c.p @ 0% ) 25 supplying and fixing of copper bus bar duly tinned by means of smc / dmc type insulator high tensile nuts and bolts spring washers fixing to same in existing panel including bending, cutting in required shape and size and insulation with colour coding heat shrinkable pvc insulation complete in all respect as per hsr 31.64 ( c.p @ 0% ) 26 pdg. and fixing digital metering equipment for lt cubical panel consisting of 96mmx96mm 0 500v, volt meter with selector switch, amp. meter ( of required ratio up to 600 / 5 amp. ) with selector switch and required c.ts 3 nos., a set of 3 no phase indicating lamps ryb led. hsr 31.65 ( c.p @ 0% ) 27 supply & fixing of rotary handle for on / off operation of existing mccb in the lt panel including fixing the same in position with all labour and material required to complete the job in all respect..hsr 31.66 ( c.p @ 0% ) i ) rotary handle up to 125a, mccb 28 s / e of mark double walled corrugated ( dwc ) hdpe pipe laid 1 mtr. below ground level including diging and refilling of earth including cost of suitable size socket / cuppler for hdpe pipe including the cost of labour and material required to complete the job in all respect upto the entire satisfaction of engineer incharge of the work. ( hsr 31.67+cp 0% ) ( ii ) hdpe pipe 90 / 75 mm outer dia / inner dia. 29 supply and erection of moulded case circuit breaker single pole / four pole on wall or on existing pedestal including bonding to earth and necessary connections. ( hsr 31.69 ) ( cp 0% ) iv ) four pole mccb 6 to 63 amp 30 v ) four pole mccb 100 amp 31 s / e of heavy duty 4 pole on load change load over breaker switch suitable for operation of 415 volt ac supply complete with handle assembling having door interlock and interlocking arrangement on existing panel i / c making necessary connections with petty material required to complete the job. hsr 31.74 ( c.p @ 0% ) ii ) 100 amp 4 pole on load changeover switch 32 total hsr 33 ns item 34 s / e of ms bucket stand suitable for 6 nos. fire buckets ( without buckets ) made out of angle from of size 40 mm x 40 mm x 6mm i / c the cost of welding, labour and two coats of approved paint including one coat of red oxide. 35 s / e of fire buckets of 9 liters capacity made out of 24 gauge gi sheet& duly painted with one coat of red oxide and two coat of approved paint in red colour written with fire as per fire protection complete with necessary sand filling in the bucket and labour etc. 36 s / e of fire existingusher isi marked c02 type of 4.5 kg capacity as per is:7285 duly erected / hangs on wall with hooks i / c the cost of hook, screws etc with all labour and material required to complete the job in all respect upto the entire satisfaction of the engineer in charge of the work. 37 s / e of fire existingushers isi marked dry chemical powder type of 4 kg capacity as per is duly erected / hangs on wall with hooks i / c the cost of hook, screws etc with all labour and material required to complete the job in all respect to the entire satisfaction of the engineer in charge of the work. 38 supply & erection of of hi rib profilrd sheeting 1000 1020 mm cover width 28.30 mm creast 200 150 mm centre to centre manufactured from 0.50 mm tct hi tensile bars galvalum sheet ( az 150 gm aluminium zink alloy metallic coating sheet ) complete with all labour and petty material required to complete the job i / c carriage, loading , unloading, westage, fixing on existing ms structure with stsc screws, nuts, bolts & washers etc.as required upto entire staisfactrion of engineer in charge of work. 39 supply, installation, testing and commissioning of 40 kva water cooled, silent diesel generating set complete with alternator rated at 3 phase, 415 volts, 0.8power factor, 50 cycle per second, 1500 rpm with amf panel ( outside the canopy ) , accoustic enclosure and battery charger etc. ( to be installed out door on existing plateform excluding cost of plateform ) : 40 ( a ) diesel engine: engine multy cylinder, developing output bhp as per 40 kva dg set, at 1500 rpm, vertical totally enclosed water cooled, comprising compression ignition, electric start, 4 strok high speed diesel engine conforming to is 4722, iso – 3046, bs – 5514. the engine shall be complete with all standard and electrical accessories as per standard supply of manufactures. the engine shall be coupled with 3 phase 415 volts 50 cycle, 0.8 pf and 1500 rpm, alternator as per is 4722 / bis 2613 rated for 24 hours of continuous operation with 10 % over load capacity for one hour in every 12 hours in every 12 hours and comprising with: 41 a ) amf panel of required size complete with all accessories as required. 42 b ) on / off start keys 43 c ) lube oil pressure guage 44 d ) fuel tank having capacity to run the d g set min. 8 hours in first fill. 45 e ) residential silencer of required size and length i / c all necessary material as required. 46 f ) 1 no. 12 volts, 130 ah, dc mtc. free batteries with leads and containers. 47 g ) avm pads fitted on base frame. 48 h ) the base frame would be fabricated from suitable m.s. channel suitable machined to perfect alignment of the engine and alternator with rigid construction and necessary reinforncement to ensure minimum viberation 49 i ) any other accessories to make the generating set functional shall be installed as per manufactures specification 50 b ) battery charger : electronic battery charger shall be installed of required size and rating for charging of battery of d.g. set. 51 c ) acoustic enclosure: it shall be provided as per technical specification as follows: 52 1 ) construction and painting: 53 i ) the enclosure shall be fabricated out of 1.60 mm thick ( 16 swg ) crca sheet silent d.g.set container shall be of modular construction with the provision to assemble and dismantle easily at site of work. 54 ii ) the base frame shall be made of ismc of suitable section ) 55 iii ) durable industries system is to be provided on the doors and doors are fitted with high quality epdm gasket to avoid leakage of sound . 56 iv ) weather proof anti corrosion treatment to be provided to the entire structure with powder coating. 57 v ) neutral / body earthing points at the side of enclosure are to be provided. 58 vi ) emergency stop push button shall be provided outside the container. 59 vii ) a tube fitting with tube rod for proper light inside canopy shall be provided. 60 2 ) acoustic insulation: 61 i ) sound proofing of the enclosure shall be done with quality rock wood / mineral wood conforming to is 8133 1933 of 25 mm thickness and density at 30 kg / m compressed along with 3 mm thick vinyl sheet and non ferrous sheet. 62 ii ) exhaust pipe is to be thoroughly insulated by covering it with glass wool and further claded with aluminium sheet. 63 75 db a noise level as per latest central pollution control board ( cpcb ) 64 note: any other material required to complete the acoustic enclosure shall be installed as per manufactures specifications. ( app. dnit for const. of police station rohrai distt. rewari ) ....

Indo Tibetan Border Police Force - Haryana

22124376 renovation of type ii 24 nos and type i 32 nos residential quarters at ss bn itbp saboli sonepat haryana sh replacement of door shutters wire gauge shutters steel windows putty and oil bound distemper renovation of type ii 24 nos and type i 32 nos residential quarters at ss bn itbp saboli sonepat haryana sh replacement of door shutters , wire gauge shutters steel windows putty oil bound distemper...

Military Engineer Services - Haryana

21390973 supply of store: 1 water storage tank cover (lid) with hook and nuts for 1000/500 ltrs capacity, as per sample make : sintex/displast/sheetal 2 ms tee hinges 150mm , as per sample 3 ms tee hinges 200mm, as per sample 4 curtain rod powder coated 25mm dia ms 5 aluminium socket 20mm for curtain rod, as per sample 6 stay rod for steel window , as per sample 7 jumper washer 20mm (pkt of 100 nos), as per sample 8 pvc funnel for curtain rod , as per sample 9 rawal plug pvc ( pkt of 100 nos), as per sample 10 oil glass putty for glass pane , make : birla or equivlant brand 11 pvc washer for bib tap 15mm ( pkt of 100 nos ) , as per sample 12 curtain rod powder coated 20 mm dia ms 13 rubber gasket 32mm wide for door and window , as per sample 14 bracket for curtain rod powder coated , as per sample 15 plain glass sheet 900mm x 600 mm x 4 mm, make : saint gobin/ modi guard/ 16 plain glass sheet 1200mm x 900 mm x 4 mm, make : saint gobin/ modi guard/...

Military Engineer Services - Haryana

16986719 tender for periodical services leakage seepage and miscellaneous b and r items in otm accommodation in domestic area : 1 old u / s bib taps 15 mm , brass / cp 2 old u / s cp pillar taps, 15 mm 3 old u / s cp stop valves / angle valves, 15 mm 4 old u / s looking mirror 5 old u / s cp shower rose 6 old u / s cp towel rail 7 old u / s ewc / iwc with seat cover 8 old u / s whb, vitreous china 9 old u / s stainless steel sink any size 10 old u / s gi tube 15 mm 11 old u / s gi tube 20 mm 12 old u / s ms curtain rods 13 old u / s wall mixture / basin mixture 14 old u / s bib taps 15 mm , brass / cp 15 old u / s cp pillar taps, 15 mm 16 old u / s shutter with chowkat not exc 1.50sqm each including iron mongry 17 old u / s shutter with chowkat exc 1.50sqm but not exc 4.00 sqm each including iron mongry 18 old u / s shutter not exc 1.00sqm each including iron mongry 19 old u / s shutter exc 1.00sqm but not exc 2.00 sqm each including iron mongry 20 old u / s preleminated particle board 18 / 19mm thick 21 scrap iron reterived from meteled shutter / steel windows 22 old u / s pvc tank covers 23 old u / s stop valve 15 mm, brass 24 old u / s float valve any description 25 old u / s bricks / brick bats 26 old u / s pvc water tanks of any description, 500 ltrs 27 old u / s pvc water tanks of any description, 1000 ltrs 28 old u / s boarding of any description 29 old u / s ac sheet any type...

Military Engineer Services - Haryana

14366041 provision of certain repair to internal water supply, sanitary items and day to day misc b r works at af stn gurgaon under ge p af gurgaon, ge ( p ) af / gur 70 / 2017 18 ( 2nd call ) 1. (a) factory made panel/ flush door shutters 2. plywood 3. laminated sheets 4. prelaminated particle board 5. pvc water tank 6. chemical water proofing compound 7. intergral water proofing treatment (liquid) 8. steel windows/ ventilators (as per is:1038:1983) 9. cold rolled steel doors & windows 10. glazed tiles, water resistant tiles/non skid tiles 11. aluminium sections 12. vitrified tiles 13. putty 14. ac pipes and fittings 15. ac sheets 16. pcc interlocking tiles/pavers 17. pcc tiles/terrazzo tiles/chequered tiles 18. acid resistant tiles 19. pvc flushing cistern is 774 1984 20. looking mirror 21. sanitary fittings 22. seat & cover for wc 23. galvalume/zincalume sheet 24. aluminium and brass mongry 25. galvanised iron tube 26. door closers 27. mortice locks 28. cement based paint 29. synthetic enamel paint 30. red oxide primer 31. oil bound distemper 32. plastic emulsion paints (distemper and emulsion) 33. chlorinated rubberised paint/epoxy paint/anti corrosive paint. 34. 100% acrylic weather proof exterior paint 35. wood primer pink 36. glass(plain frosted tinted)/ mirrors 37. cement base putty 38. pvc rain water pipes 39. ci rain water pipes 40. pvc flooring tiles /sheets 41. water proofing membrane 42. fire clay bricks and tiles 43. glazed fire clay kitchen sinks 44. bib tap, stop valve, pillar taps 45. fancy bib tap, stop valves, pillar taps, wall mixing unit 46. false ceiling with grid and boards 47. rolling shutters 48. rust prevention anti corrosive chemicals 49. sealing compound for joints in concrete 50. fibre reinforced concrete (pfrc) manhole covers 51. pressed steel door/ window frames...

Military Engineer Services - Haryana

14262928 repair / replacement of steel window and grills in multistoried building quarters in a, b, c type at o f estate dehradun under ge ( i ) ( p ) ( fy ) kanpur,...

Military Engineer Services - Haryana

12505445 tender for providing of certain major revenue works and lbw works incl repair to joinery steel windows rolling shutters air conditioner sheets and connected works at asp af station faridabad...

Military Engineer Services - Haryana

12497848 provision of certain major revenue works and lbw works incl repair to joinery steel windows rolling shutters ac sheets and connected works at asp af station faridabad, b r works...

Public Works Department - Haryana

11993518 replace of 4 no steel window construction of inlet channel and hodies at ww sindhvi khera and all other works contingent thereto...

Hindustan Petroleum Corporation Limited - Haryana

10743800 civil sor jobs under hisar weep holes , structural steel , ms pipe railing , chain link fencing , precastconcretepoles fencing , barbed wire fencing , hume pipes 1000 mm dia (np4) , hume pipes 600 mm dia (np3) , hume pipes 450 mm dia (np 3) , hume pipes 250 mm dia (np 3) , anti termite treatment , rectifiedtiles compound wall , ceramictile , vitrifiedtile900mm x 900mm , terracotta tiles , manglore tiles on roof /chajja , mosaic tiles , ips flooring , granite tile flooring , ips flooring , granite skirting , cermictiledado( 300mmx 200 mm) , cermictiledado( 300mmx 400 mm) , cermictiledado( 300mmx 600 mm) , granite slab18 mm black , hp logo fixing , kotastonefloor:600mm x 600mm , kota stone skirting , granite sill slab for windows , kota stone steps , concrete tile walkway , brickbat terrace water proof. , integral terrace waterproofing , chajja water proofing , white wash oil bound distember , acrylicemulsion paint(int/grd) , acrylicemulsion paint(ext) , plasticemulsion paint , water proofcement paint , sy. enml. paint over wall , sy.enml.paint over steel/wood , pop punning , pop moulding , ms grill , anod.al.glz. door 12mm glass , anod.al.glzdoor 12mm toughened , pdr.coat.al glz. fixed 10mm , hy. floor spring , al. panelled door , al. windows openable , al. sliding windows 3 track , al. sliding windows 2 track , al. louvered ventilator , steel windows , steel doors , flush door 900x2100mm: , flush door 750x2100mm , rolling shutter , grill in rolling shutter , ms fan hooks , door closer , mortice lock , nonasbestos cement sheet roof , barricading...

Hindustan Petroleum Corporation Limited - Haryana

10743787 tender for civil sor jobs ceramictile 450mmx450mm , ceramictile 300mmx300mm , vitrifiedtile900mm x 900mm , terracotta tiles , manglore tiles on roof /chajja , mosaic tiles ,ips flooring , granite skirting , cermictiledado( 300mmx 400 mm) , cermictiledado( 300mmx 600 mm) , granite slab18 mm black , kotastonefloor:600mm x 600mm , kota stone steps , granite sill slab for windows , concrete tile walkway , brickbat terrace water proof , integral terrace waterproofing , chajja water proofing , white wash , oil bound distember ,acrylicemulsion paint(int/grd) , acrylicemulsion paint(ext) , water proofcement paint , sy. enml. paint over wall , pop punning , pop moulding , ms grill , anod.al.glzdoor 12mm toughened , pdr.coat.al glz. fixed 10mm , hy. floor spring , al. panelled door , al. windows openable , al. sliding windows 3 track , al. louvered ventilator , steel doors , steel windows , flush door 900x2100mm , flush door 750x2100mm , rolling shutter , grill in rolling shutter , ms fan hooks , mortice lock , door closer , nonasbestos cement sheet roof , nonasbestos cement sheet side , barricading ,...

Hindustan Petroleum Corporation Limited - Haryana

10743779 tender for civil sor jobs ceramictile 450mmx450mm , ceramictile 300mmx300mm , vitrifiedtile900mm x 900mm , terracotta tiles , manglore tiles on roof /chajja , mosaic tiles ,ips flooring , granite skirting , cermictiledado( 300mmx 400 mm) , cermictiledado( 300mmx 600 mm) , granite slab18 mm black , kotastonefloor:600mm x 600mm , kota stone steps , granite sill slab for windows , concrete tile walkway , brickbat terrace water proof , integral terrace waterproofing , chajja water proofing , white wash , oil bound distember ,acrylicemulsion paint(int/grd) , acrylicemulsion paint(ext) , water proofcement paint , sy. enml. paint over wall , pop punning , pop moulding , ms grill , anod.al.glzdoor 12mm toughened , pdr.coat.al glz. fixed 10mm , hy. floor spring , al. panelled door , al. windows openable , al. sliding windows 3 track , al. louvered ventilator , steel doors , steel windows , flush door 900x2100mm , flush door 750x2100mm , rolling shutter , grill in rolling shutter , ms fan hooks , mortice lock , door closer , nonasbestos cement sheet roof , nonasbestos cement sheet side , barricading ,...

Military Engineer Services - Haryana

8587814 repair/replacement to rain water pipes, steel windows and chajjas to md accommodation under age b/r ii of ge (north) ambala cantt, repair/replacement to rain water pipes, steel windows and chajjas to md accn under age b/r ii of ge (north) ambala cantt...

Military Engineer Services - Haryana

8587812 repair/replacement to rain water pipes, steel windows and chajjas to md accn under age b/r i of ge (north) ambala cantt, repair/replacement to rain water pipes, steel windows and chajjas to md accn under age b/r ii of ge (north) ambala cantt...

East-Northern Railway - Haryana

4088758 repair to complete sewerage system of chandigarh station building, repair to circulating area main entry road of chandigarh railway station and repair to suits of officer’s rest house/ chandigarh by replacing steel windows & ventilations with aluminimum windows & ventilators and repair to wooden doors & wire gauge shutters in the section of sse/w/chandigarh under aden/rajpura ...